Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Performance Emission and Combustion Characteristics of CRDI Engine Operating on Jatropha Curcas Blend with EGR(Elsevier Ltd, 2018) Bedar, P.; Kumar, G.N.The present experimental study uses dual cylinder common rail direct injection (CRDI) engine fuelled by Jatropha curcas biodiesel blends produced through Transesterification process along with application of water cooled exhaust gas recirculation (EGR) rates. Performance, emissions and combustion properties of an engine at constant speed were measured and analysed. The improvement in brake thermal efficiency (BTE) along with reduction in carbon monoxide (CO), unburned hydrocarbons (UBHC) and smoke opacity were observed for the B20 biodiesel blend with a marginal increase in oxides of nitrogen (NOx). EGR application has reduced the NOx emissions and peak pressure inside the combustion chamber due to lower flame temperature. Combining B20 blend ratio with 15% EGR rate has the potential to achieve ultra-low NOx without affecting other type of diesel engine exhaust emissions by maintaining same efficiency level. © 2018 Elsevier Ltd.Item Comparison and Feasibility Study of Hexanol/Diesel/Pongamia Biodiesel Blend on Engine Characteristics of a Common Rail Direct Injection Diesel Engine(SAE International, 2024) Santhosh, S.; Shahapur, S.; Kumar, G.N.; Ravikumar, K.N.; Raghavendra Reddy, N.V.In this work, the impact of hexanol/diesel/biodiesel blend on engine characteristics of a common rail direct injection (CRDI) diesel engine was studied. Biodiesel is more viscous in nature and higher cetane count, hexanol has a lower viscosity and cetane count. The drawbacks of both biodiesel and hexanol can be overcome by blending both hexanol and biodiesel with diesel fuel in the right proportion. Tests were carried out using a 4-stroke CRDI engine with two cylinders. Biodiesel and 1-hexanol were blended in a ratio of 10% each by volume with diesel and compared with B10D90 and B20D80 blends. It was noted that the addition of hexanol enhances the combustion characteristics of the engine. At 20% load H10B10D80 showed71.34 bar which is highest compared to other fuels in the test. The blends had a positive effect on emissions, there was drastic reduction in NOx was noticed, also HC and CO emission was lower than diesel emissions. The lowest CO, and HC emission is obtained for H10B10D80, which is 66%, 92% lower at 60% load compared to baseline readings. However, the blend had a slight negative effect on performance in contrast to diesel. The higher latent heat of vaporization of hexanol led to low temperature combustion contributing to the lowest NOx emissions. The combination of both hexanol and Pongamia biodiesel with diesel showed an effective reduction in greenhouse gases. Which will also reduce the dependency on fossil fuels. The lower carbon content of 1-hexanol contributes towards carbon neutrality. Overall, the hexanol and biodiesel are sustainable alternatives to the diesel fuel. © 2024 SAE International. All rights reserved.Item Effect of exhaust gas recirculation (EGR) on diesel engine using Simarouba glauca biodiesel blends(Regional Energy Resources Information Center (RERIC) enreric@ait.ac.th, 2015) Bedar, P.; Pandey, J.K.; Kumar, G.N.This article deals with the usage of non-edible Simarouba glauca (paradise) oil as a biodiesel for single cylinder diesel engine with application of exhaust gas recirculation (EGR) rates. Biodiesel blends B10, B20 with EGR rates of 10%, 15%, and 20% are used for different load conditions. Parameters like brake thermal efficiency (BTE), nitrogen oxides (NOx), carbon monoxide (CO), hydrocarbons (HC) and smoke opacity were evaluated from the experimental study. The results show that Simarouba glauca biodiesel usage decreases HC, CO and smoke emissions with slight increase of NOx, also an improvement in the performance was observed for B10 blend. EGR rates 10% and 15% are beneficiated in terms of performance and emission but negative trend is observed for 20% EGR rate. On the whole it is concluded that a better trade-off between NOx and other emissions is attained with simultaneous application of EGR (15%) and biodiesel blend (B10) without compromising engine performance.Item Performance and emission analysis of a single cylinder CI engine using Simarouba glauca biodiesel(Springer Heidelberg, 2017) Bedar, P.; Chitragar, P.R.; Shivaprasad, K.V.; Kumar, G.N.It is well known fact that diesel engines are commonly used for transportation and power generation due to their high efficiency, low fuel consumption and durability. On contrary these engines churn out harmful and hazardous emissions like particulate matter (PM) and nitrogen oxides (NOx). Recently Bio-origin renewable fuels have taken center stage of discussion because of their ability to replace depleting fossil fuels and capacity to reduce hazardous engine exhausts emissions when used in diesel engines. In the present experimental study Simarouba glauca biodiesel is used in a naturally aspirated four stroke single cylinder air cooled direct injection kirloskar DA10 engine. The main objective is to investigate the effect of biodiesel and exhaust gas recirculation (EGR) on the performance and emission characteristics of a CI engine at 180 bar fuel injection pressure (FIP) with standard injection timing. B20, B40 biodiesel blends with 10, 15 and 20% EGR ratios were used for the study to investigate brake thermal efficiency (BTE), carbon monoxide (CO), unburned hydrocarbons (UBHC), NOx, and smoke opacity. Reduction in CO, HC and smoke opacity is noticed with simarouba biodiesel fuel while increasing NOx compared to diesel. Application of EGR along with biodiesel resulted in simultaneous reduction of nitrogen oxides and smoke without affecting engine performance. It was found from experiment that B20 blend at 15% EGR shown superior performance characteristics compared to other conditions. © Springer India 2017.Item Effect of injection pressure on the performance and emission characteristics of the CI engine using Vateria indica biodiesel(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2019) Rao, G.; Kumar, G.N.; Herbert, M.A.Vateria indica Linn seeds were found to contain nearly 19% of oil/fat content. This fat is converted into biodiesel by a novel method by the authors at the biodiesel preparation facility at NITK, Surathkal, India. As biodiesel is a promising alternative fuel for petro diesel in compression ignition (CI) engines, this biofuel is tested in a single-cylinder diesel engine. The objective of this work is to find combustion, performance and emission characteristics of a CI engine with diesel and blends of V. indica biodiesel at 180, 200 and 220 bar injection pressures. Blending is done in volumetric ratios of 10%, 15%, 20% and 25% of biodiesel with diesel which are called as B10, B15, B20 and B25. The idea of increasing fuel injection pressure is to promote atomisation and full penetration into the combustion chamber leading to better combustion. Blend B25 showed best thermal efficiency of the order of 33.03% and the least NOX emission of 1047 ppm at 220 bar injection pressure at 75% load. © 2018, © 2018 Informa UK Limited, trading as Taylor & Francis Group.Item Combustion, performance and emission analysis of preheated KOME biodiesel as an alternate fuel for a diesel engine(Springer Science and Business Media B.V., 2020) Kodate, S.V.; Yadav, A.; Kumar, G.N.In the present work, karanja oil methyl ester (KOME) biodiesel is used in a compression ignition engine to find an alternative to diesel. The use of biodiesel in a CI engine leads to poor performance and high brake specific fuel consumption due to the higher viscosity and lower calorific value of biodiesel. This problem can be reduced by increasing the injection temperature of biodiesel or its blends to a certain temperature. In this study, working fuel is tested at preheating temperatures of 95 °C for various loading conditions (0, 25, 50, 75 and 100%). Effect of different KOME biodiesel–diesel blends (B0, B30, B50 and B100) on engine performance, combustion and emissions is studied at different loads. At higher temperature, the viscosity of the fuel decreases which leads to better combustion, improves the atomization as well as vaporization of fuel in a diesel engine, resulting in higher engine performance and lower emissions of CO and HC, with slight increment in NOX and CO2 emission compared to unheated neat diesel and biodiesel blends. The result shows that for 100% biodiesel (B100) at full load, BTE is improved by 9.1% compared to unheated case. Preheating of B100 fuel upto 95 °C at full load decreases the BSFC, CO and HC emission by 6.5%, 8.1% and 10.6%, respectively, compared to unheated case. © 2020, Akadémiai Kiadó, Budapest, Hungary.Item Investigation of preheated Dhupa seed oil biodiesel as an alternative fuel on the performance, emission and combustion in a CI engine(Elsevier Ltd, 2021) Kodate, S.V.; Satyanarayana Raju, P.; Yadav, A.K.; Kumar, G.N.The present study investigates the suitability of preheated Vateria indica methyl ester (VIME) as an alternative fuel for a diesel engine. VIME is a renewable, non-toxic and sustainable alternative biodiesel obtained from Dhupa fat by transesterification. This study aims to evaluate the combustion, performance, and emission characteristics of four different blends such as B0 (0% VIME and 100% mineral diesel), B30, B50 and B100 at elevated fuel inlet temperatures ranging from 35 °C to 95 °C. The tests are carried out in a single cylinder diesel engine at optimum loading condition and fixed speed. Results are obtained in terms of brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), in-cylinder pressure, heat release rate and exhaust emissions (CO, HC, NOX, CO2 and soot). It is observed that the preheating of blends decreases the viscosity which enhances fuel spray characteristics, leading to higher engine performance, lower CO and HC emissions with a slight increase in NOX and CO2 emissions. BTE and peak in-cylinder pressure for B100 at 95 °C and 75% load are increased by 7.44%, 2.97% respectively compared to unheated B100 biodiesel. BSFC, CO, HC emissions at 75% load for B100 at 95 °C are reduced by 26.73%, 28.08%, 42.7% respectively compared to unheated B100. © 2021 Elsevier LtdItem The effect of tri-fuel blends on engine characteristics of a direct injection diesel engine with exhaust gas recirculation(Taylor and Francis Ltd., 2022) Santhosh, K.; Kumar, G.N.; Shahapur, S.Biofuels are the most promising alternative to petro-diesel. In this work, the combined effect of mahua biodiesel and 1-Hexanol is studied on the engine characteristics. The concentration of both 1-Hexanol and mahua biodiesel is varied, 10%, 20%, and 30% each with diesel fuel. Common rail direct injection diesel engine is used in this study. Engine load is varied from 20% to 80% in step of 20%, the speed of the engine is constant throughout the experiment. Biofuel blends showed improved cylinder pressure and mean gas temperature at a higher engine load. At 60% load, 10H10M80D (10% 1-Hexanol/10% mahua biodiesel/80% diesel) showed 3.45% lower thermal efficiency and 6.11% higher fuel consumption compared to diesel. At 60% load, all the biofuel blends showed 50% lower carbon monoxide emission. At 60% load, 10H10M80D showed 33.33% lower hydrocarbon emission and 0.96% higher nitrogen oxide emission compared to baseline readings. The biofuel blends are less sensitive to exhaust gas recirculation (EGR) due to the oxygenated nature of biofuels. With 20% EGR, at 60% load, 10H10M80D showed 39.48% lower nitrogen oxide compared to no EGR. The results of 10H10M80D showed the best performance at all loads. © 2022 Taylor & Francis Group, LLC.