Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.Kumar, G.N.Subject: search.filters.subject.Alternative fuels

Search Results

Now showing 1 - 7 of 7
  • No Thumbnail Available
    Item
    Effect of hydrogen addition on combustion and emissions performance of a high speed spark ignited engine at idle condition
    (Serbian Society of Heat Transfer Engineers, 2018) Shivaprasad, K.V.; Chitragar, P.R.; Kumar, G.N.
    The fuel depletion and environmental pollution have pushed studies on improving the combustion and emission characteristics of internal combustion engines with several alternative fuels. Expert studies proved that hydrogen is one of the prominent energy source which has exceptional combustion qualities that can be used for improving combustion and emissions performance of gasoline-fueled spark ignition engines. This paper introduced an experiment conducted on a single cylinder high speed gasoline engine equipped with a hydrogen injection system to discover the combustion and emissions characteristics with various hydrogen gasoline blends at idle condition. For this purpose, the conventional carburetted high speed spark ignition engine was modified into an electronically controllable engine with help of electronic control unit which dedicatedly used to control the ignition timings and injection duration of gasoline fuel. © 2018 Society of Thermal Engineers of Serbia.
  • No Thumbnail Available
    Item
    Effect of exhaust gas recirculation on a CRDI engine fueled with waste plastic oil blend
    (Elsevier Ltd, 2018) Ayodhya, A.S.; Lamani, V.T.; Bedar, P.; Kumar, G.N.
    The inevitable rise in the usage of plastic poses a serious threat to the environment owing to their non-biodegradable nature. The lack of proper infrastructure for treating and recycling plastic wastes give rise to the disposal problem. However, the oil synthesized from these waste plastics can be used as an alternative fuel for C.I engines which not only helps to tackle the disposal problem but also aids in recovering precious energy from these wastes. This experimental investigation aims to study the effects of plastic-diesel blend(P30) fuel on the performance, emission and combustion characteristics of a twin cylinder CRDI engine operating at different EGR rates (0%, 10% and 20%). The experimental results showed a slight drop in the engine performance while operating with plastic blend, mainly overall due to its higher viscosity and lower heating value. The vast upsurge of NOX emissions with plastic blend was mitigated by the aid of EGR methodology. Marginal increase in the discharge of regulated emissions like HC, CO and soot were noticed for both plastic blend as well as EGR operations. The experiments were carried out for five different loading conditions varying from 0% to 80% in steps of 20% each and found out that waste plastic-diesel blend can be successfully used as an alternative fuel in diesel vehicles without any prior modifications in the engine. © 2018 Elsevier Ltd
  • No Thumbnail Available
    Item
    Combustion, performance, and tail pipe emissions of common rail diesel engine fueled with waste plastic oil-diesel blends
    (American Society of Mechanical Engineers (ASME) infocentral@asme.org, 2018) Lamani, V.T.; Yadav, A.K.; Kumar, G.N.
    The demand for plastic is eternally growing in urban areas and producing enormous quantity of plastic waste. The management and disposal of plastic waste have become a major concern worldwide. The awareness of waste to energy retrieval is one of the promising modes used for the treatment of the waste plastic. The present investigation evaluates the prospective use of waste plastic oil (WPO) as an alternative fuel for diesel engine. Different blends (WPO0, WPO30, and WPO50) with diesel are prepared on a volume basis and the engine is operated. Experiments are conducted for various injection timings (9 deg, 12 deg, 15 deg, and 18 deg BTDC) and for different exhaust gas recirculation (EGR) rates (0%, 10%, 15%, and 20%) at 100 MPa injection pressure. Combustion, performance, and tail pipe emissions of common rail direct injection (CRDI) engine are studied. The NOx, CO, and Soot emissions for waste plastic oil-diesel blends are found more than neat diesel. To reduce the NOx, EGR is employed, which results in reduction of NOx considerably, whereas other emissions, i.e., CO and Soot, get increased with increase in EGR rates. Soot for WPO-diesel blends is higher because of aromatic compounds present in plastic oils. Brake thermal efficiency (BTE) of blends is found to be higher compared to diesel. © 2018 by ASME.
  • No Thumbnail Available
    Item
    NOx reduction studies on a diesel engine operating on waste plastic oil blend using selective catalytic reduction technique
    (Elsevier B.V., 2019) Ayodhya, A.S.; Lamani, V.T.; Thirumoorthy, M.; Kumar, G.N.
    The constant escalation in the consumption of petroleum products has compelled researchers to discover for new alternative fuels which can be successfully incorporated in the existing automotive engines. Oil derived from waste plastics is one such alternative, which not only ensures longevity of fossil fuels but also assists in bringing down the hazardous impacts caused by the improper disposal of plastic wastes. This work focuses on the utilization of valuable energy of toxic non-biodegradable waste plastics to lucratively be used as an alternative fuel. An attempt was further made to reduce the NO X emissions which increased with the use of waste plastic oil blend. The main objective of this experimental investigation is to study the performance & emission characteristics of a twin cylinder CRDI engine subjected to selective catalytic reduction (SCR) after-treatment technique. Different flow rates of ammonia as a reducing agent were tested and concluded that a flow rate of 0.5 kg/hr furnishes optimum results. A comparison of NO X reduction efficiency was also made between SCR and EGR techniques. The comparison eventually indicated that SCR gives better NO X conversion efficiency at higher loads without any adverse effect on the engine performance while operating on Waste Plastic Oil blend (P30). © 2018 Energy Institute
  • No Thumbnail Available
    Item
    Effect of injection pressure on the performance and emission characteristics of the CI engine using Vateria indica biodiesel
    (Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2019) Rao, G.; Kumar, G.N.; Herbert, M.A.
    Vateria indica Linn seeds were found to contain nearly 19% of oil/fat content. This fat is converted into biodiesel by a novel method by the authors at the biodiesel preparation facility at NITK, Surathkal, India. As biodiesel is a promising alternative fuel for petro diesel in compression ignition (CI) engines, this biofuel is tested in a single-cylinder diesel engine. The objective of this work is to find combustion, performance and emission characteristics of a CI engine with diesel and blends of V. indica biodiesel at 180, 200 and 220 bar injection pressures. Blending is done in volumetric ratios of 10%, 15%, 20% and 25% of biodiesel with diesel which are called as B10, B15, B20 and B25. The idea of increasing fuel injection pressure is to promote atomisation and full penetration into the combustion chamber leading to better combustion. Blend B25 showed best thermal efficiency of the order of 33.03% and the least NOX emission of 1047 ppm at 220 bar injection pressure at 75% load. © 2018, © 2018 Informa UK Limited, trading as Taylor & Francis Group.
  • No Thumbnail Available
    Item
    Effect of hydrogen enrichment on performance, combustion, and emission of a methanol fueled SI engine
    (Elsevier Ltd, 2021) Nuthan Prasad, B.S.; Pandey, J.K.; Kumar, G.N.
    The study of potentially high rated alternative fuel (Methanol) for the IC engines is an exciting topic in the recent research advancement. However, the study of combination of methanol and hydrogen is considered to address both economic and environmental needs. Hydrogen with best combustion characteristics will compensate for the drawbacks of methanol as a fuel. In the present investigation hydrogen enrichment to methanol has shown a significant enhancement in performance and combustion; the overall emission has reduced substantially. The experiments for a different set of trials, including hydrogen enrichment ranging between 5% and 20% with 2.5% increment, the engine is operated with wide-open throttle (WOT) condition for different speeds. The increase in enrichment of hydrogen has shown a rise in BTE, BP, and a reduced BSEC value. The percentage increase in BTE is between 20 and 30%, and an increase in hydrogen beyond 12.5% would affect the volumetric efficiency, and thus performance declines after that. The exhaust emissions have a huge impact on hydrogen enrichment; CO, HC, and CO2 emission are reduced by 30–40%; however, an increase in cylinder temperature due to rapid combustion slightly increases the NOx emission. Thus hydrogen enriched methanol operating at higher compression ratio can improve the overall engine characteristics significantly. © 2021 Hydrogen Energy Publications LLC
  • No Thumbnail Available
    Item
    Investigation of preheated Dhupa seed oil biodiesel as an alternative fuel on the performance, emission and combustion in a CI engine
    (Elsevier Ltd, 2021) Kodate, S.V.; Satyanarayana Raju, P.; Yadav, A.K.; Kumar, G.N.
    The present study investigates the suitability of preheated Vateria indica methyl ester (VIME) as an alternative fuel for a diesel engine. VIME is a renewable, non-toxic and sustainable alternative biodiesel obtained from Dhupa fat by transesterification. This study aims to evaluate the combustion, performance, and emission characteristics of four different blends such as B0 (0% VIME and 100% mineral diesel), B30, B50 and B100 at elevated fuel inlet temperatures ranging from 35 °C to 95 °C. The tests are carried out in a single cylinder diesel engine at optimum loading condition and fixed speed. Results are obtained in terms of brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), in-cylinder pressure, heat release rate and exhaust emissions (CO, HC, NOX, CO2 and soot). It is observed that the preheating of blends decreases the viscosity which enhances fuel spray characteristics, leading to higher engine performance, lower CO and HC emissions with a slight increase in NOX and CO2 emissions. BTE and peak in-cylinder pressure for B100 at 95 °C and 75% load are increased by 7.44%, 2.97% respectively compared to unheated B100 biodiesel. BSFC, CO, HC emissions at 75% load for B100 at 95 °C are reduced by 26.73%, 28.08%, 42.7% respectively compared to unheated B100. © 2021 Elsevier Ltd