Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item HVOF sprayed Ni3Ti and Ni3Ti+(Cr3C2+20NiCr) coatings: Microstructure, microhardness and oxidation behaviour(Elsevier Ltd, 2018) Reddy, N.C.; Kumar, B.S.A.; Reddappa, H.N.; Ramesh, M.R.; Koppad, P.G.; Kord, S.This paper reports the development of Ni3Ti and Ni3Ti+(Cr3C2+20NiCr) coatings on AISI 420 stainless steel (MDN-420) and titanium alloy ASTM B265 (Ti-15) by HVOF technique. Microstructure, microhardness and high temperature oxidation behaviour of coatings were investigated. Microstructure of coatings was dense and displayed layers depicting lamellar structure. The microhardness of coatings was significantly higher than that of substrate owing to higher density and cohesive strength between individual splats of coating materials. Cyclic oxidation studies conducted on Ni3Ti and Ni3Ti+(Cr3C2+20NiCr) coatings showed oxide scale was composed of various oxides like NiO, NiCr2O4 and Cr2O3 phases. The formation of compact and protective NiO phase in case of Ni3Ti coatings; NiO and Cr2O3 phases in Ni3Ti+(Cr3C2+20NiCr) coatings stabilised the weight gain exhibited slow oxidation rate at higher temperatures. © 2017 Elsevier B.V.Item Microstructure and tribological characteristics of APS sprayed NiCrBSi/flyash cenosphere/Cr2O3 and NiCrBSi/flyash cenosphere/Mo composite coatings at elevated temperatures(Institute of Physics Publishing helen.craven@iop.org, 2019) Nagabhushana, N.; Rajanna, S.; Mathapati, M.; Ramesh, M.R.; Koppad, P.G.; Reddy, N.C.In the present investigation NiCrBSi/flyash/Cr2O3 and NiCrBSi/flyash/Mo composite coatings are developed using atmospheric plasma spray technique on superni 76 alloy. Coatings are characterized in terms of microstructure, phase analysis, and microhardness. Tribological properties of the coatings are evaluated using a pin on disc tribometer. Test is conducted under dry sliding conditions at room temperature, 200 °C, 400 °C, and 600 °C respectively. Microstructure and worn surfaces of the coatings are analyzed by utilizing Scanning Electron Microscope (SEM) where in phase analysis is carried out using x-ray diffractometer (XRD). XRD results revealed the presence of ?-Ni as primary phase along with Ni3B, Cr7C3, SiO2 and Al2O3 as minor phases in both the NiCrBSi/flyash/Cr2O3 and NiCrBSi/flyash/Mo coatings. Among the two coatings, Mo composite coating exhibited lower porosity and higher microhardness. The friction coefficient of both the coatings decreased with increasing temperature. The wear rate is found to decrease at lower temperatures but increased at a higher temperature (>400 °C) for Cr2O3 composite coating wherein Friction coefficient is decreased with increase in the temperature for Mo composite coatings. The worn surface analysis conducted revealed abrasive wear at lower temperatures while the transition from abrasive to adhesive is observed at higher temperatures. © 2019 IOP Publishing Ltd.Item Microstructure, microhardness, and tensile properties of hot-rolled Al6061/TiB2/CeO2 hybrid composites(South African Institute of Mining and Metallurgy, 2021) Iyengar, S.; Sethuram, D.; Shobha, R.; Koppad, P.G.TiB2 and CeO2 particle-reinforced Al6061 hybrid composites were manufactured using stir casting and hot rolling techniques. The base alloy and composites were hot-rolled at 500ºC and a 50% reduction was achieved through 12 passes. The effect of varying TiB2 and CeO2 particle additions on the microstructure and mechanical properties of the Al6061 matrix was studied. Scanning electron microscopy showed uniform dispersion of both the reinforcements, with good interfacial bonding. Microhardness and tensile properties like yield and tensile strength were found to be higher for hybrid composite with 2.5% TiB2 and 2.5% CeO2 compared to Al6061 alloy and other hybrid composites. The increased tensile strength is attributed to good dispersion and interfacial bonding between the particles and Al6061 matrix. Fracture analysis using a scanning electron microscope revealed ductile fracture for the Al6061 alloy and mixed characteristics of ductile-brittle fracture for hybrid composites. © 2021 South African Institute of Mining and Metallurgy. All rights reserved.Item Effect of carbon nanotubes on microhardness and adhesion strength of high-velocity oxy-fuel sprayed NiCr–Cr3C2 coatings(SAGE Publications Ltd, 2022) Manjunatha, M.; Gaikwad, G.; Natarajan, J.; Koppad, P.G.NiCr–Cr3C2 coatings are widely used for high temperature and tribological applications due to their high hardness, oxidation, and wear resistance properties. In the present investigation, an attempt is made to further enhance the hardness and adhesion strength of NiCr–Cr3C2 coatings by reinforcing them with multi-walled carbon nanotubes. The carbon nanotubes (3–7 wt%) with varying weight percentages were mixed with NiCr–Cr3C2 using a planetary ball rolling mill and sprayed on SA213 T12 (T12 alloy steel tube) using a high-velocity oxy-fuel spraying process. The microstructures of mixed powder, coating cross-section, and fractured coating surface were characterized using a scanning electron microscope while X-ray diffraction was used for phase identification in the fractured coating surface. The coated samples were subjected to microhardness and adhesion strength tests according to ASTM E384 and ASTM D4541-09 standards. Out of all coatings, NiCr–Cr3C2/7% carbon nanotube composite coating showed the lowest porosity of 1.17%, highest microhardness, and adhesion strength of 563.8 HV and 55.8 MPa, respectively. A fracture analysis after a pull-off adhesion test revealed adhesion failure for NiCr–Cr3C2 coating and combined adhesion/cohesion failure for NiCr–Cr3C2/7% carbon nanotube composite coating. © IMechE 2021.Item Hardness and electrical conductivity of uncoated and silver coated carbon nanotubes reinforced copper nanocomposites(Springer, 2022) Koti, V.; Mahesh, n.; Murthy, K.V.S.; Koppad, P.G.; Sethuram, D.In the present study, carbon nanotube reinforced copper nanocomposites were fabricated using the powder metallurgy technique which includes ball milling and hot pressing. The carbon nanotube weight percentage in the nanocomposite was varied from 0.25 to 1.50% in the steps of 0.25%. Further, to improve the interfacial bonding between the carbon nanotubes and copper matrix, the carbon nanotubes were coated with silver using the electroless deposition method. The sintered and hot pressed copper nanocomposites with uncoated and silver-coated carbon nanotubes were subjected to optical and scanning electron microscope studies to understand the dispersion of nanotubes. The density, microhardness and electrical conductivity of developed nanocomposites were studied. The dispersion of nanotubes was found to be uniform throughout the copper matrix resulting in the improvement in microhardness. Especially when compared with sintered samples, the hot-pressed nanocomposites with silver-coated carbon nanotubes showed significant improvement in microhardness however beyond 0.75% content the microhardness for samples was found to drop. The electrical conductivity of nanocomposites was found to decrease with the increase in the MWCNT content which was attributed to the clustering of MWCNTs due to strong van der Waal forces and the increase in the number of interfaces between MWCNTs and copper matrix. © 2022, Indian Academy of Sciences.