Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Investigation on Properties of Shape Memory Alloy Wire of Cu-Al-Be Doped with Zirconium(Springer, 2020) Singh, R.K.; Murigendrappa, S.M.; Kattimani, S.Abstract: In this paper, the effect of wire drawing on the microstructures, mechanical properties, and shape memory effect of compositions Cu87.85-Al11.70-Be0.45 (CAB) and Cu87.73-Al11.70-Be0.45-Zr0.12 (CABZ) has been experimentally investigated. The wires with a diameter of 1.33 mm are manufactured from the casted round bars through the rolling and drawing (secondary) process. Investigations are performed on microstructure and phase for both as-cast and wire-drawn SMAs. Further, wire-drawn SMAs are investigated for phase transformation temperatures, hardness, ductility, and shape memory effect. The results show that the average grain size decreased with 73.06% by adding Zr to the CAB alloy. Further, the grain size of CABZ alloy wire decreased with 67.38% in the longitudinal direction and 67.07% in the transverse direction as compared to CAB alloy wire after the secondary process. Improvement of the grain structure in CABZ alloy wire resulted in an enhancement in the hardness of 13.86% in longitudinal and 12.43% in the transverse direction, and tensile strength of 134.58% and ductility of 177.06%. The phase transformation temperatures reduced by the addition of Zr, and better shape recovery is observed in CABZ alloy wire. Graphic Abstract: [Figure not available: see fulltext.] © 2020, ASM International.Item Pseudoelastic Behavior of Boron-Doped ?1 -Type Cu-Al-Be Shape Memory Alloys(Springer, 2021) Kalinga, T.; Murigendrappa, S.M.; Kattimani, S.This paper examines the influence of 0-0.2 wt.%B-doping on the microstructure, mechanical properties, and pseudoelastic behavior of Cu-Al11.5-Be0.57 shape memory alloys (SMAs). This microstructure study reveals that the addition of boron leads to significant grain refinement in ?1-type polycrystalline Cu-Al-Be SMAs. A maximum refinement size of 50 µm was achieved with the addition of 0.15 wt.%B. The fine-grained (Cu-Al11.5-Be0.57)-B0.15 SMA with serrated grain boundaries exhibited the maximum enhancement of ultimate tensile strength, 744.65 ± 29.34 MPa, and ductility of 21.93 ± 0.56%. The fracture morphology revealed the transformation of intergranular to transgranular fracture in the SMAs with boron-doping. Maximum pseudoelasticity of 4% was achieved in the SMA with 0.15 wt.%B and suits as a damper in seismic applications. © 2021, ASM International.Item An experimental evaluation of the microstructure, mechanical and functional fatigue properties of the boron-doped Cu-Al-Be SMA wires(Elsevier Ltd, 2021) Singh, R.K.; Biswas, P.; Murigendrappa, S.M.; Kattimani, S.An experimental evaluation of the microstructure, mechanical and functional fatigue properties of the Cu-11.70Al-0.45Be doped with Bx (x = 0.05, 0.10, 0.12, and 0.14 wt%) SMA wires has been carried out. The experiments were performed to investigate microstructure, phase/precipitates, and transformation temperatures for both as-cast and wire samples. Furthermore, tensile properties, shape recovery ratio, and functional fatigue evaluation have also been carried out for the wire samples. The investigation shows that the addition of the minor amount of boron and secondary processes involved during the specimen preparation induced excellent grain refinement. The addition of boron decreased transformation temperatures; however, there was not a considerable change observed due to the secondary process. It was observed that tensile properties increases with the boron addition, and complete shape recovery was observed for all the selected alloys. Finally, functional fatigue tests were conducted under constant stress condition and observed that the number of cycles until the failure has increased and more distance recovery was achieved with an increase in boron doping. © 2021Item Role of alloying additions on phase transformations, mechanical and pseudoelastic behavior of Cu-Al-Be shape memory alloys(Elsevier Ltd, 2022) Kalinga, T.; Bala Narasimha, G.; Murigendrappa, S.M.; Kattimani, S.In this study, the influence of alloying additions on phase transformations, microstructure, transformation temperatures, mechanical properties, and pseudoelastic behavior of polycrystalline Cu-Al-Be shape memory alloy has been investigated. Four different SMAs were prepared in the range of 11.0–11.8 wt.% of aluminum and 0.5–0.6 wt.% of beryllium. Results reveal that the alloying of Al ≥ 11.5 wt.% and Be ≥ 0.57 wt.% forms austenite β1(DO3) at room temperature. An increase in both aluminum and beryllium decreases the transformation temperatures, and Cu-11.5Al-0.57Be SMA exhibits smaller energy differences (ΔH) between austenite and martensite. Alloying aluminum and beryllium didn't exhibit significant improvement in mechanical properties due to the existence of coarse grains. Maximum pseudoelasticity of 4% was achieved in Cu-11.5Al-0.57Be SMA with a retained strain of 0.192%. © 2021Item Experimental investigation of the pseudoelastic behavior on zirconium modified Cu-Al-Be shape memory alloys for seismic applications(IOP Publishing Ltd, 2022) Kalinga, T.; Murigendrappa, S.M.; Kattimani, S.This paper examines the effect of 0.05-0.3 wt.% of zirconium-doping on microstructure, transformation temperatures, tensile properties, and pseudoelastic behavior of the parent β1 -phase Cu87.93-Al11.5-Be0.57 shape memory alloys (SMAs). Results reveal that alloying zirconium in the evaluated SMA samples exhibits an excellent grain refinement up to 0.15 wt.%. Further, higher additions of Zr ≥ 0.2 wt.% lowers the grain refinement efficiency due to precipitates agglomeration. Larger the size and volume fraction of Al3Zr precipitates led to higher transformation temperatures. Tensile properties were improved with Zr-doping, resulting enhancements in the maximum tensile strength and ductility with the addition of 0.15 wt.% Zr. The alloy with 0.05 wt.% of Zr-dope showed a good pseudoelastic strain recovery of deformation strain and then lowered by retaining large residual strain, indicating deterioration in the pseudoelasticity of SMAs. © 2022 IOP Publishing Ltd.