Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Effect of boundary conditions and convection on thermally induced motion of beams subjected to internal heating(2007) Malik, P.; Kadoli, R.; Ganesan, N.Numerical exercises are presented on the thermally induced motion of internally heated beams under various heat transfer and structural boundary conditions. The dynamic displacement and dynamic thermal moment of the beam are analyzed taking into consideration that the temperature gradient is independent as well as dependent on the beam displacement. The effect of length to thickness ratio of the beam on the thermally induced vibration is also investigated. The type of boundary conditions has its influence on the magnitude of dynamic displacement and dynamic thermal moment. A sustained thermally induced motion is observed with progress of time when the temperature gradient being evaluated is dependent on the forced convection generated due to beam motion. A finite element method (FEM) is used to solve the structural equation of motion as well as the heat transfer equation. © Springer-Verlag 2007.Item Stress analysis of SUS 304 - Ceramics functionally graded beams using third order shear deformation theory(2008) Akhtar, K.; Kadoli, R.Kinematics for moderately thick rectangular beams satisfying zero shear strain on the top and bottom . surfaces is utilized to define the strain displacement relations involving the membrane, bending and higher order of displacements. Strain energy containing shear rotation term is deduced. The principle of stationary potential energy is used to obtain the static finite element equilibrium equations for the FGM (functionally graded material) beam with a uniformly distributed transverse load. FGM beams with continuous and smooth grading of metal and ceramics based on po wer law index are considered for the study. Equivalent single layer approach is followed for the evaluation of the constitutive matrix of the FGM beam. Numerical results are presented on the axialstresses and shear stresses in SUS304-Al3O3, SUS 304-ZrO2 and SUS 304-Si3N4FGM beams with clamped-clamped and simply supported boundary conditions. The effect of volume fraction of ceramic and metal on the nature of stress distribution through the thickness are investigated. The studies reveal that, the magnitude and distribution profile of static stresses in the beam depends on the power law index and also on the nature of load bearing surface, ie, whether the loading is on the ceramic rich face of the beam or metal rich face.Item Thermo-elastic response of SUS316-Al2O3 functionally graded beams under various heat loads(Elsevier Ltd, 2017) Malik, P.; Kadoli, R.Geometric nonlinearity and temperature dependent material properties are accounted for in the theoretical analysis of time dependent thermo-elastic response of thin functionally graded material (FGM) SUS316-Al2O3 beam subjected to various heat loads. A two dimensional Lagrangian rectangular finite element is used to obtain the temperature distribution on the transverse plane of the beam. Nonlinear thermo-elastic deflection and thermal stresses are evaluated for various structural and thermal boundary conditions. Thermo-elastic oscillations are observed in case of beams subjected to step, concentrated line and shock heat load whereas thermo-elastic deflection is observed for beams subjected to moving heat load. As the thermal load increases, the nonlinear thermal deflection of FGM beam are higher compared to linear analysis. In general, temperature dependency of material properties influence the amplitude of thermal oscillations. High thermal stresses are induced in beams with pin-pin and clamp-pin boundary condition as compared to hinge-hinge beam. © 2017 Elsevier LtdItem Differential quadrature solution for vibration control of functionally graded beams with Terfenol-D layer(Elsevier Inc. usjcs@elsevier.com, 2020) Patil, M.A.; Kadoli, R.The governing differential equation of motion for vibration control of a functionally graded material (FGM) beam using magnetostrictive layers is solved using differential quadrature method(DQM). It is known that, when differential quadrature is implemented directly for the solution of governing differential equation for vibration control of beam, it is required to convert the generalised eigenvalue problem into standard eigenvalue problem. However in the present work, the original differential equation of vibration control of beam is be separated into two simpler second and fourth order differential equations using the separation of variables in conjunction with the characteristics equation of damped single degree of freedom system. Solution of corresponding two simpler differential equation also yields damped natural frequency and damped factor comparable to that of the former approach. It is to be noted that using either of the solutions using differential quadrature method ? point description of the physical domain at boundary is used to obtained the differential quadrature equations for the various boundary conditions of the beam. In order to assure the accuracy of formulation and solution using DQM, convergence behavior of natural frequencies is examined for five combinations of boundary conditions and comparison studies from the two solution approaches is presented. The effect of the location of the magnetostrictive layers, material properties and control parameters on the vibration suppression are investigated. © 2020 Elsevier Inc.Item Influence of Winkler and viscoelastic foundation on free vibration of functionally graded beam integrated with Terfenol-D layer(Springer Science and Business Media Deutschland GmbH info@springer-sbm.com, 2020) Patil, M.A.; Kadoli, R.Free vibration of functionally graded beam integrated with Terfenol-D layer on Winkler-two parameter and viscoelastic foundation are studied by means of differential quadrature method within the framework of classical beam theory. The material properties of functionally graded beam integrated Terfenol-D layer are estimated by using the rule of mixture. The applied kinematic boundary conditions are implemented using ?-point and modified weighting coefficient approach. The solution of simply supported functionally graded material beam with Terfenol-D layer (FGMT) resting on the Winkler elastic foundation is obtained by using the technique of Navier. The numerical results obtained using differential quadrature method (DQM) and modified differential quadrature method (MDQM) are compared with exact results obtained from analytical formulation where excellent agreement is observed. The parametric study is carried out to encapsulate the influence of Winkler-two parameter and the viscoelastic foundation on the vibration characteristics of functionally graded beams integrated with Terfenol-D layer. © 2020, The Brazilian Society of Mechanical Sciences and Engineering.Item Analytical solution for free vibration of symmetric Terfenol-D layered functionally graded beam with different boundary conditions(Springer Science and Business Media Deutschland GmbH, 2023) Patil, M.A.; Kadoli, R.A unified analytical approach is established to predict the frequency behaviour of symmetric functionally layer-wise graded beams with an integrated Terfenol-D layer under simply supported, clamped-clamped, and clamped-simply supported boundary conditions. In contrast to previous research, the analytical solution relies on transcendental equations. Terfenol-D layered functionally graded beam uses Reddy’s generalised beam theory as the basis for its governing equation. First-order shear deformation and rotating inertia were taken into consideration in the study. To ensure the accuracy of the analytical solution, comparisons are made with the current differential quadrature solution based on Euler–Bernoulli beam theory. The current analytical solution yields frequency results that are in good agreement with those obtained by the differential quadrature approach. The present analytical means is straightforward and easy to understand as compared to previous researcher’s work. © 2023, The Author(s), under exclusive licence to The Brazilian Society of Mechanical Sciences and Engineering.