Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Effect of microwave heating on microstructure and elevated temperature adhesive wear behavior of HVOF deposited CoMoCrSi-Cr3C2 coating(Elsevier B.V., 2019) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.This research reports the improvement of high-temperature sliding wear resistance of a grade 15 titanium alloy protected by an HVOF sprayed CoMoCrSi-Cr3C2 coating. The coatings have been tested in as-sprayed condition and after a post-deposition microwave heating step. The powder feedstock has been manufactured by high energy ball milling. X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM) equipped with the Energy Dispersive Spectroscopy (EDS) methods were used for coatings characterization. Surface roughness, microhardness, adhesion strength, and porosity of coatings were also measured. The wear test was conducted at an applied load of l0 N and 20 N with varying temperatures of 200 °C, 400 °C, and 600 °C under dry sliding conditions. Co3Mo2Si, Co7Mo6, Mo3Si, Co3Mo, and Co2Mo3 were the intermetallic laves phases generated in the CoMoCrSi feedstock during HEBM process. The microwave-fused coating exhibited metallurgical bonding, homogeneous structure, less porosity, and greater hardness as compared to as-sprayed coating. Microwave-treated coating revealed better wear property than an as-sprayed coating. This was mainly due to the intermetallic formation and metallurgical bonding in coatings. The fused coatings exhibit tribo-oxide layers during sliding action which was the main phenomenon of improving the wear resistance of the fused composite coatings. © 2019 Elsevier B.V.Item Comparison of Microstructural and Sliding Wear Resistance of HVOF Coated and Microwave Treated CoMoCrSi-WC + CrC + Ni and CoMoCrSi-WC + 12Co Composite Coatings Deposited on Titanium Substrate(Springer Science and Business Media B.V. editorial@springerplus.com, 2020) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.CoMoCrSi-WC + CrC + Ni and CoMoCrSi-WC + 12Co composite coatings are coated on titanium substrate by high velocity oxygen fuel method (HVOF). Prior to spraying, CoMoCrSi feedstock are processed through high energy ball milling (HEBM) in order improve the intermetallic laves phases and to reduce its particle size. The processed feedstock exhibits amorphous nature by improving laves phases and particle size of 60.12 ?m. Microwave heating energy is utilized as post heat treatment technique to improve the mechanical and metallurgical properties of as-sprayed coatings. Fused coatings reveals better properties in terms of surface roughness, porosity, microhardness and adhesion strength compared to as-sprayed coatings. Metallurgical bonding is observed in case of fused coatings due to diffusion of substrate elements. Frictional and wear behaviors have been investigated by a pin on disc apparatus at temperatures of 200 °C, 400 °C, and 600 °C under normal loads of 10 N and 20 N. Both wear trace and friction coefficients of the fused coatings are smaller than as-sprayed coatings and substrate at all test temperatures. The wear traces of fused coatings decreased with increasing the surface temperature due to the lubricant effect of cobalt oxides formed on the sliding surface. As a result, cobalt based cermet coatings are highly recommended as a durability improvement coating for the protection of sliding surface, such as high speed spindle. © 2020, Springer Nature B.V.Item Microstructural and Tribological Resistance of Flame-Sprayed CoMoCrSi/WC-CrC-Ni and CoMoCrSi/WC-12Co Composite Coatings Remelted by Microwave Energy(Springer, 2020) Prasad, C.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.The hard facing composite coatings such as CoMoCrSi/30%WC-CrC-Ni and CoMoCrSi/30%WC-12Co are coated on grade-2 titanium substrate through Flame spray technique. Prior to deposition of coatings CoMoCrSi feedstock were processed using high energy ball milling to obtain intermetallic laves phases. The sprayed coatings are subjected to post-heat treatment through microwave energy to homogenize coating structure which reduces surface defects and to achieve metallurgical bonding. The as-sprayed and microwave treated coatings are examined for metallography analysis by using XRD, SEM–EDS and mechanical properties are estimated by using microhardness, universal tensile equipment. The high-temperature sliding wear tests are performed against alumina counterpart under dry conditions. The sliding wear test is conducted with normal loads of 10 N and 20 N at a sliding velocity of 1.5 m/s with a constant sliding distance of 3000 m. Microwave treated coatings obtained homogeneous structure and metallurgical bonding with improved hardness. Fused coatings revealed better wear resistance due to formation of oxides and fatigue spalling mechanism. © 2020, Springer Nature Switzerland AG.Item Effect of temperature on wear and friction performance of WC-Co and Cr3C2 reinforced with 17-4PH Fe-based composite coatings(Springer Science and Business Media Deutschland GmbH, 2024) Chandramouli, T.V.; Joladarashi, S.; Ramesh, M.R.; Rahman, M.R.Surface protection is crucial in industrial equipment and tools to prevent wear and friction in harsh environments, particularly at high temperatures, where anti-friction coatings are essential for optimal performance. The present research investigates the tribological properties of high-velocity oxy-fuel sprayed coatings of 17-4PH stainless steel reinforced with tungsten carbide and chromium carbide powders. The coatings are deposited onto a maraging steel substrate. A dry sliding wear test was performed using an alumina ball as a counter body under various test temperatures (25 °C, 300 °C, and 600 °C) and loads (10 N and 30 N). The coating is characterized by employing SEM, XRD, micro-hardness tester, particle analyzer, and bond strength tester, and the mechanism of wear reduction was discussed. The post-wear analysis was carried out on the wear track using SEM/EDS and 3D non-contact optical profilometers. The micro-hardness and bond strength of both (17-4PH-30%WC-Co and 17-4PH-30%Cr3C2) coatings are compared. The test results revealed that at all temperatures and loads, 17-4PH-30%WC-Co coating shows better wear resistance and lower friction coefficient than the 17-4PH-30%Cr3C2 coating. The significant influence of the tribo-oxide layer at high temperatures, which contributed to decreasing wear rate and coefficient of friction, was premeditated. © 2023, International Institute of Welding.Item Tribological characteristics of HVOF sprayed Fe-based composite coatings at elevated temperatures(SAGE Publications Ltd, 2025) T V, C.; Joladarashi, S.; Ramesh, M.R.This study evaluates the tribological performance of Fe-based composite coatings for aerospace and automotive applications, focusing on wear resistance at elevated temperatures. The coatings, comprising 15% WC-Co and Cr3C2 in an SS316L matrix, were deposited onto maraging steel via HVOF spraying. Microstructural analysis and adhesive strength testing confirmed strong particle bonding, with the coatings achieving a hardness of 711 ± 14?HV. Dry sliding wear behaviour was assessed using a ball-on-disc tribometer with alumina as the counterface under 10?N and 30?N loads at 25?°C, 300?°C, and 600?°C. Results indicated a decrease in the coefficient of friction and specific wear rate with increasing load and temperature. At 600?°C, wear rates were reduced by ?97.56% (10?N) and ?97.12% (30?N) than uncoated steel. Abrasive wear dominated at room temperature, while adhesive and oxidative wear mechanisms emerged at 600?°C, attributed to protective glaze layer formation. © The Author(s) 2025.Item Microstructure, Mechanical Properties, and Tribological Properties of Fe-Based Composite Coatings Reinforced with WC-Co and Cr3C2(Springer, 2025) Chandramouli, T.V.; Joladarashi, S.; Ramesh, M.R.; Rahman, M.R.Fe-based (stainless steel 316L) coatings are widely employed in the aerospace, chemical processing, petrochemical, and marine industries owing to their low and stable price, excellent corrosion resistance, and durability. However, at elevated temperatures, their performance is limited due to wear. Thus, the current investigation incorporates tungsten carbide (WC-Co) and chromium carbide (Cr3C2) into the Fe-based coating to enhance its wear resistance at high temperatures. SS316L reinforced by 30% of WC-Co and Cr3C2 by mechanical mixture, then sprayed using high-velocity oxy fuel spraying method. Coating characteristics, such as microstructures and phase analysis, were measured using FESEM/EDS and XRD. Coating density, microhardness, and bond strength were examined by water immersion, Vickers indentation, and ASTM C-633 methods, respectively. A ball-on-disk tribometer was employed to conduct wear examination at various temperatures (25, 300, and 600 °C) and loads (10 and 30 N) against the alumina counter body. The wear rate and friction coefficient of SS316L-30%WC-Co decrease from 25 to 600 °C, while the wear rate of SS316L-30%Cr3C2 increases with temperature up to 300 °C and then decreases at 600 °C. The oxide phase adheres strongly to underlying surfaces forming a protective layer (Cr2O3, NiWO4, Fe2O3, and NiMO4), changing the mode of wear mechanism. At higher temperatures and loads, the coating exhibited oxidation modified adhesive wear, and coatings provide excellent wear resistance along with reduction in friction. This research provides a novel approach for future standardization and evaluation of coatings on metal alloys for industrial applications. © ASM International 2024.