Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Mechanical Properties of Natural Fiber Braided Yarn Woven Composite: Comparison with Conventional Yarn Woven Composite(Science Press bcanji@mail.sioc.ac.cn, 2017) RAJESH, M.; Jeyaraj, J.The effect of reinforcing natural fiber in the form of braided yarn woven fabric on mechanical properties of polymer composite was investigated. The results of braided yarn fabric composites were compared with the conventional yarn fabric composite and random oriented intimately mixed short fiber composites for the same percentage of fiber weight. The effect of intra-ply hybridization, by keeping two different natural fiber yarns along two different directions of a woven fabric, on mechanical properties of the woven fabric composite was also analyzed. Natural fiber braided yarn fabric reinforcement significantly increased the mechanical properties of the composites compared with that of the conventional woven fabric and short fiber reinforcements. Intra-ply hybridization of two different natural fibers improved the mechanical properties of the conventional woven fabric composite while it could not enhance the properties of the braided fabric composite. The improvement in impact property is very high compared to tensile and flexural properties due to the braided yarn fabric reinforcement. © 2017 Jilin UniversityItem Mechanical and dynamic mechanical behaviour of novel glass–natural fibre intra-ply woven polyester composites(Springer India sanjiv.goswami@springer.co.in, 2017) RAJESH, M.; Jeyaraj, J.A novel intra-ply woven fabric polyester composite with glass fibre yarns in one direction and natural fibre yarns in another direction of basket-type woven fabric has been investigated for mechanical and dynamic mechanical characteristics. Individual glass fibre woven fabric, natural fibres woven fabric and intra-ply natural fibres woven fabric composites are also investigated for the comparison purpose. Results reveal that the intra-ply woven fabric hybridization enhances impact and damping properties of the composite significantly than the tensile and flexural properties. Intra-ply woven fabrics with glass fibre yarns in warp direction and jute fibre yarns in weft direction (WGWJ) exhibit better impact properties compared with woven fabric with other combinations. Dynamic mechanical analysis results reveal that intra-ply woven fabric composite with glass fibre yarns in warp direction and jute and banana fibre yarns in weft direction (WGWJAB) gives higher damping characteristics due to the multi-level interaction between fibre–fibre and fibre–matrix interactions. © 2017, Indian Academy of Sciences.Item Fracture toughness of flax braided yarn woven PLA composites(Bellwether Publishing, Ltd., 2021) Kanakannavar, S.; Jeyaraj, J.Flax fiber braided yarn plain woven fabric reinforced Poly Lactic Acid (PLA) bio-composites are fabricated using film stacking and hot-press compression molding method. Effect of fiber weight fraction on tensile and fracture properties of the bio-composites is studied and fractured surfaces are analyzed using scanning electron microscope (SEM) images. It is found that tensile modulus and strength increases by 62.11 and 59.75% respectively for 35 wt.% of the braided fabric reinforcement compared to pristine PLA. Fracture toughness study is performed on single-edge-notched-bend (SENB) specimens using three point bending method. It is found that plane-strain fracture toughness (KIC) and strain energy release rate (GIC) values of the PLA composites are 71.61 and 124% higher than pure PLA for 35 wt.% braided fabric reinforcement. KIC values of the braided fabric reinforced PLA composites are much high compared to similar natural fiber composites reported in literature. This is attributed to high resistance offered by the interweaving yarns of the braided fabric hence more energy is required to begin crack propagation compared to other typical forms of reinforcement. © 2021 Taylor & Francis Group, LLC.Item Fabrication and mechanical properties of braided flax fabric polylactic acid bio-composites(Taylor and Francis Ltd., 2022) Kanakannavar, S.; Jeyaraj, J.This paper primarily describes the development of flax braided yarn fabric reinforced thermoplastic composites. Plain woven fabric is made by interlacing 3D braided yarn produced by solid braiding method. Tensile properties of braided yarn and woven fabric are evaluated. Solution casting is used prior to composite fabrication to prepare polylactic acid (PLA) and (natural fiber braided fabric) NFBF–PLA sheets. Followed by this, composite laminates are prepared using through film stacking and compression molding. Influence of number of layers of fabric and loading along warp and weft directions on mechanical properties such as tensile, flexural and impact properties are presented. It is observed that the reinforcement enhances the tensile, flexural and impact properties of the composite significantly for the warp loading. Results also clearly indicates that braided yarn fabric reinforcement have the potential for significant improvement of mechanical and thermal properties of PLA composites. © 2021 The Textile Institute.Item Free Vibration of Flax Braided Fabric PLA Beam under Edge Compression(Taylor and Francis Ltd., 2022) Kanakannavar, S.; Jeyaraj, J.The present study focuses on the development of biodegradable composites to replace synthetic polymer-based composites for potential lightweight structural applications in the automobile, aeronautical, marine, and packaging industries. Initially, PLA and NFBF/PLA films are prepared by solution casting, and from these films, composite laminates are prepared by film sequencing and compression (hot-press) molding methods. First, the critical buckling load (Pcr) of composites is analyzed, and then, the influence of compressive load on natural frequency is studied. The critical buckling load-bearing capacity of PLA is enhanced with the reinforcement of NFBF (natural fiber braided yarn fabric). The composite with three layers of NFBF registered the highest critical-buckling load (Pcr) of 374.19 N, and this value is 172.13% high compared to the virgin PLA. Similarly, the natural frequency of the NFBF composites approaches minimum when the applied load is equal to the corresponding Pcr. However, a significant increase in the fundamental frequency is noticed when the applied load is higher than the Pcr. © 2021 Taylor & Francis.Item A semi-analytical nonlocal elasticity model for static stability and vibration behaviour of agglomerated CNTs reinforced nano cylindrical panel under non-uniform edge loads(Elsevier Inc., 2022) Twinkle, C.M.; Jeyaraj, J.A semi analytical nonlocal elasticity model to analyze the effect of non-uniform edge loads on static stability and free vibration characteristics of agglomerated carbon nanotubes (CNTs) reinforced nano cylindrical panels are presented. Effective material properties of the agglomerated CNT reinforced composite are obtained using a two-parameter micro-mechanics model while Eringen's non-local theory is used to account the size effect. Sinusoidal shear deformation theory is adopted to analyze the buckling and vibration parameters using Galerkin's approach. The accuracy of the proposed model is presented first by comparing the results in the literature. Then a comprehensive study is carried out to analyze the influence of various degrees of agglomeration (complete, partial), nature of edge load, and non-local effects on the buckling and free vibration response of CNT reinforced nano cylindrical panel. The results revealed that non-local size effect leads to a reduction in stiffness and thus reduces buckling and dynamic characteristics. Moreover, it is observed that critical buckling load varies with type of in plane load and reduction in natural frequency is different for different in plane loading conditions. © 2021 Elsevier Inc.Item Biodegradation properties and thermogravimetric analysis of 3D braided flax PLA textile composites(SAGE Publications Ltd, 2022) Kanakannavar, S.; Jeyaraj, J.; Thalla, A.K.; RAJESH, M.Recent advances in the development and application of bio-based (natural fiber and biopolymer) composites are gaining broad attention because the resulting polymer completely degrades and does not release harmful substances. In this study, natural fiber 3 D braided yarn textile PLA (Polylactic acid) bio-composites are developed by film sequencing followed by hot-press compression molding. Bio-deterioration and thermal stability of the composites are analysed for storage, machining, transportation, and in-service uses in different environmental conditions (compost and thermal). Composite samples with different fiber wt.% (0, 22, 44) are exposed to compost soil. Tensile testing is performed under different configurations to characterise the tensile properties. Prepared bio-composite specimens are evaluated for weight loss and reduction in tensile properties over soil burial time, to observe the rate of biodegradation of braided yarn textile bio-composites. Fourier transform infrared (FTIR) and scanning electron microscopy (SEM) is employed to analyse the biodegradability of the composites. To study the thermal stability of the prepared bio-composites thermogravimetric (TG) analysis is carried out. Results showed that biodegradability, tensile properties and thermal stability of the composites are enhanced significantly with the reinforcement of 3 D braided yarn fabric. © The Author(s) 2021.Item Study on tearing strength of woven sisal fabrics for tents and polymer composite applications(Taylor and Francis Ltd., 2023) Nagamadhu, M.; Kivade, S.B.; Jeyaraj, J.; Kumar, G.C.; Shivaraj, B.W.; Bharath, K.N.The use of plant fibers as a reinforcement in composites has increased daily owing to their favorable environmental considerations. Fabric properties play a significant role in alignment during composites processing, enhancing the composite properties. However, the fabric structures are formed by warp and weft yarns. These yarns are subjected to axial and shear loads, respectively. However, very limited work has been carried out on the study involving the tearing strength of the fabric. So it is necessary to study the effect of the tearing load of fabrics before converting them into composites. This paper focuses on the tearing strength of the sisal woven fabrics in both warp and weft directions. Two plain and one weftrib fabrics are prepared using sisal fibers, and their physical properties were characterized as per textile testing standards. Tear strength has been determined by Elmendorf Tear and Single Rip Tear Method by varying crosshead speeds. The result shows that woven patterns and number yarns significantly impact tearing strength. In the case of the weft rib pattern, the warp direction exhibits the highest tearing strength compared to the weft direction. Also, in the case of weftrib fabrics, the weft direction indicates better-tearing strength than another woven pattern. © 2023 The Author(s). Published with license by Taylor & Francis Group, LLC.