Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
3 results
Search Results
Item Validation of an integral sliding mode control for optimal control of a three blade variable speed variable pitch wind turbine(Elsevier Ltd, 2015) RAJENDRAN, S.; Jena, D.Reduction in cost of wind energy requires most efficient control technology which can able to extract optimum power from the wind. This paper mainly focuses on the control of variable speed variable pitch wind turbine (VSVPWT) for maximization of extracted power at below rated wind speed (region 2) and regulation of extracted power when operating at above rated wind speed (region 3). To extract maximum power at below rated wind speed torque control is used whereas to regulate rated power at above rated wind speed pitch control is used. In this paper a nonlinear control i.e. integral sliding mode control (ISMC) is proposed for region 2 whereas a conventional proportional-integral (PI) control is adapted for region 3 of a VSVPWT. The proposed controller is combined with modified Newton Raphson (MNR) wind speed estimator to estimate the wind speed. The stability of the proposed ISMC is analyzed using Lyapunov stability criterion and the control law is derived for region 2 which is also adapted for the transition period between region 2 and region 3 (region 2.5). The dynamic simulations are tested with nonlinear FAST (Fatigue, Aerodynamics, Structures, and Turbulence) wind turbine (WT). The simulation results of ISMC are presented and the control performance is compared with conventional SMC and existing controllers such as aerodynamic torque feed forward control (ATF) and Indirect speed control (ISC). It is seen that especially in region 2.5, ISMC gives better performance compared to all other controllers. © 2015 Elsevier Ltd.Item Backstepping sliding mode control of a variable speed wind turbine for power optimization(2015) RAJENDRAN, S.; Jena, D.To optimize the energy capture from the wind, wind turbine (WT) should operate at variable speed. Based on the wind speed, the operating regions of the WT are divided into two parts: below and above the rated wind speed. The main aim at below rated wind speed is to maximize the energy capture from the wind with reduced oscillation on the drive train. At above rated wind speed, the aim is to maintain the rated power by using pitch control. This paper presents the control of WT at below rated wind speed by using backstepping sliding mode control (BSMC). In BSMC, generator torque is considered as the control input that depends on the optimal rotor speed. Usually, this optimal rotor speed is derived from effective wind speed. In this paper, effective wind speed is estimated from aerodynamic torque and rotor speed by using the modified Newton Rapshon (MNR) algorithm. Initially, a conventional sliding mode controller (SMC) is applied to the WT, but the performance of the controller was found to be less robust with respect to disturbances. Generally, WT external disturbance is not predictable. To overcome the above drawback, BSMC is proposed and both the controllers are tested with mathematical model and finally validated with the fatigue, aerodynamics, structures, and turbulence (FAST) WT simulator in the presence of disturbances. From the results, it is concluded that the proposed BSMC is more robust than conventional SMC in the presence of disturbances. © 2015, The Author(s).Item Control Strategy to Maximize Power Extraction in Wind Turbine(Taylor and Francis Inc. 325 Chestnut St, Suite 800 Philadelphia PA 19106, 2016) RAJENDRAN, R.; Jena, D.This article deals with nonlinear control of variable speed wind turbine (VSWT), where the dynamics of the wind turbine (WT) is obtained from a single mass model. The main objective of this work is to maximize the energy capture form the wind with reduced oscillation on the drive train. The generator torque is considered as the control input to the WT. In general the conventional control techniques such as Aerodynamic Torque Feed-Forward (ATF) and Indirect Speed Control (ISC) are unable to track the dynamic aspect of the WT. To overcome the above drawbacks the nonlinear controllers such Sliding Mode Controller (SMC) and SMC with integral action (ISMC) with the estimation of effective wind speed are proposed. The Modified Newton Raphson (MNR) is used to estimate the effective wind speed from aero dynamic torque and rotor speed. The proposed controller is tested with different wind profiles with the presence of disturbances and model uncertainty. From the results the proposed controller was found to be suitable in maintaining a trade-off between the maximum energy capture and reduced transient on the drive train. Finally both the controllers are validated by using FAST (Fatigue, Aerodynamics, Structures, and Turbulence) WT simulator. © Association of Energy Engineers (AEE).