Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
12 results
Search Results
Item A Study on the Seismic Behaviour of Embankments with Pile Supports and Basal Geogrid(Springer, 2020) Patel, R.M.; Jayalekshmi, B.R.; Shivashankar, R.For constructing the roads on soft grounds, basal geogrid-reinforced pile-supported embankments are a suitable solution over other conventional ground improvement techniques like preloading, embankment slope flattening, removing and replacing the soft soil, etc. Many studies are available on these basal geogrid-reinforced piled embankments to understand their behaviour under static loading conditions. But it is necessary to understand the behaviour of these geogrid-reinforced piled embankments under seismic excitations. Hence, finite element analysis of three-dimensional models of embankment having crest width of 20 m, height above ground of 6 m, with side slopes of 1V:1.5H consisting of pulverized fuel ash, overlying soft marine clay of 28 m thickness is carried out under seismic excitations corresponding to Zone III (IS:1893). Soft marine clay layer is improved by the addition of piles arranged in square grid pattern with 5.75% area replacement ratio. Geogrid with a tensile modulus of 4600 kN/m is used as the basal reinforcement. Initially, the embankment is analyzed without geogrid reinforcement and pile supports. Then, it is analyzed with (i) Basal geogrid (ii) With pile supports (iii) With basal geogrid and pile supports. The influence of various parameters of the embankment on maximum crest displacements, differential settlements at crest, toe horizontal displacements, stresses at pile head and foundation soil between piles and pile bending moment along the depth at peak acceleration are studied. Analysis of results shows that the embankment supported over piles with basal geogrid reinforcement will experience less crest settlements, differential settlements at crest and toe horizontal displacements due to earthquake load. © 2020, Springer Nature Singapore Pte Ltd.Item Seismic Response of Basal Geogrid Reinforced Embankments Supported on a Group of Vertical and Batter Piles(Springer Science and Business Media Deutschland GmbH, 2021) Patel, R.M.; Jayalekshmi, B.R.; Shivashankar, R.; Surya, N.R.Basal geogrid reinforced embankments supported on vertical piles are proven to be a feasible and effective solution for constructing embankments over thick soft clay deposits and bridge approaching embankments. These solutions minimize the lateral displacements, total and differential settlements of embankment crest and toe by transmitting embankment loads into the deeper stratum through pile foundations and arching action of geogrid. Basal geogrid reinforcements provide good restraint against lateral spreading of the toe. Providing batter piles near the toe will further enhance this restraint against lateral spreading. Not many studies are available in literature on performance of batter piles below embankment toe, especially under seismic excitations. The present study aims to find the advantages of providing batter piles below embankment toe under seismic excitations. A 6 m high basal geogrid reinforced embankment having 1 V:1.5H side slope constructed over 28 m thick soft clay is considered for the 3-Dimensional finite element analysis. The soft clay is stabilized with 22 m long 300 mm diameter vertical and batter piles spaced at three times the pile diameter. Embankment crest vertical displacements, toe horizontal displacements, maximum differential settlements at the crest and crest lateral accelerations are analysed for different batter angles of 0°, 5°, 10°, 15°. Analysis of results reveals that larger the batter angle more is the reduction of toe horizontal displacements. © 2021, The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.Item 3D soil–structure interaction analyses of annular raft foundation of tall RC chimneys under wind load(Springer, 2014) Jisha, S.V.; Jayalekshmi, B.R.; Shivashankar, R.Three dimensional soil–structure interaction (SSI) analyses of tall reinforced concrete chimneys with annular raft foundation subjected to wind loads are presented in this paper. Different ranges of height and slenderness ratios of the chimneys and different ratios of external diameter to thickness of the annular raft were selected for the parametric study. To understand the significance of SSI, four types of soils were considered based on the stiffness. The chimneys were assumed to be located in terrain category two and subjected to a maximum wind speed of 50 m/s as per IS:875 (Part 3)-1987. The alongwind and across-wind loads were computed according to IS:4998 (Part 1)-1992. The linear elastic behavior was assumed for the integrated chimney-foundation-soil system and it was analysed using finite element software ANSYS based on direct method of SSI. The radial and tangential moments and settlement of annular raft foundation were evaluated through SSI analysis and compared with that obtained from conventional method of analysis as per IS:11089-1984, assuming foundation system is rigid. From the analysis, it is concluded that the SSI analysis results in higher radial moments and lesser tangential moments as compared to conventional method. All these variations depend on the geometric properties of chimney and annular raft foundations. © Indian Geotechnical Society 2013.Item Soil–Structure Interaction Effect on Seismic Force Evaluation of RC Framed Buildings with Various Shapes of Shear Wall: As Per IS 1893 and IBC(Springer India sanjiv.goswami@springer.co.in, 2015) Jayalekshmi, B.R.; Chinmayi, H.K.Behaviour of a structure is altered by the interaction amid the structure, foundation and the soil medium below the foundation. This mutual dependent behaviour of structure and soil is called as soil–structure interaction (SSI). Hence, it is not realistic to analyse a structure as per conventional structural design practice which considers the base to be fixed. Comparative study on seismic provisions of Indian seismic code, IS 1893:2002 (IS) and International building code IBC:2006 (IBC) is carried out in present study to look into the effect of soil flexibility on variation in natural period, spectral acceleration coefficient, base shear and storey shear. Multi-storey reinforced concrete framed buildings of varying height with various shapes of shear walls over raft foundation were considered. Analysis of 3D SSI models with three different shear wall shapes founded on four different soil types which are classified based on shear wave velocity has been carried out using finite element software LS DYNA. Study shows the significant effects of SSI in altering the seismic response of structure. It also shows that the base shear obtained as per IBC are higher than the IS values and the corrugated shape of shear wall experience the lowest base shear compared to cylindrical and rectangular shape shear walls for buildings with aspect ratio below 3. © 2014, Indian Geotechnical Society.Item Dynamic soil-structure interaction analysis of RC framed building with various positions of shear walls(CAFET INNOVA Technical Society 1-2-18/103, Mohini Mansion, Gagan Mahal Road, Domalguda, Hyderabad 500029, 2016) Chinmayi, H.K.; Jayalekshmi, B.R.In the present study, a three-dimensional dynamic soil-structure interaction analysis of symmetric buildings in time domain is performed using IS spectrum ground motion record corresponding to zone III to evaluate the dynamic response of structure-foundation-soil system. Three types of shear wall buildings of aspect ratio 1, 1.5, 2, 3 and 4 categorized based on the shear wall locations were considered in conjunction with four types of soil of shear wave velocities ranging from 150m/s to 1200 m/s, symbolizing soil classes B, C, D and E of FEMA-356: 2000. Integrated structure-foundation-soil systems were analyzed using commercial finite element software LSDYNA, based on direct method of soil-structure interaction (SSI) assuming linear elastic behavior. The study shows considerable variation in dynamic characteristics and structural seismic response of the structure due to the incorporation of the effect of flexibility of soil and position of shear walls. Tall buildings with shear walls placed at the exterior corners experience the least base shear. © 2016 CAFET-INNOVA TECHNICAL SOCIETY. All rights reserved.Item Effect of soil stiffness on seismic response of reinforced concrete buildings with shear walls(Springer, 2016) Jayalekshmi, B.R.; Chinmayi, H.K.Buildings are subjected to lateral loads caused by wind, blasting and earthquakes. The high stresses developed by these loads literally tear the building components apart, which are in general designed for gravity loads. To resist these lateral forces, shear walls can be introduced in buildings. Present study aims to determine the apt shear wall position which attracts the least earthquake forces in symmetric plan multi-storey buildings. Dynamic response of a structure is significantly influenced by the underlying soil due to its natural ability to deform. Three dimensional finite element soil–structure interaction analyses of reinforced concrete shear wall buildings with shear walls placed at various locations is carried out in time domain using scaled down Elcentro ground motion to determine the seismic response variation in the structure due to the effect of stiffness of soil. Four different soil types based on shear wave velocity and six varying shear wall positions in multi-storey buildings up to 16 storeys are considered to determine the effect of soil–structure interaction. From the study, it is found that structural response as per conventional fixed base condition is very conservative. For buildings founded on soil with Vs ? 300 m/s, providing the shear walls at the core is advantageous whereas for soil with Vs > 300 m/s, the shear walls placed at exterior corners of the building attracts the least earthquake force. © 2016, Springer International Publishing Switzerland.Item Analysis of Foundation of Tall R/C Chimney Incorporating Flexibility of Soil(Springer India sanjiv.goswami@springer.co.in, 2017) Jayalekshmi, B.R.; Jisha, S.V.; Shivashankar, R.Three dimensional Finite Element (FE) analysis was carried out for 100 and 400 m high R/C chimneys having piled annular raft and annular raft foundations considering the flexibility of soil subjected to across-wind load. Stiffness of supporting soil and foundation were varied to evaluate the significance of Soil-Structure Interaction (SSI). The integrated chimney-foundation-soil system was analysed by finite element software ANSYS based on direct method of SSI assuming linear elastic material behaviour. FE analyses were carried out for two cases of SSI namely, (1) chimney with annular raft foundation and (2) chimney with piled annular raft foundation. The responses in raft such as bending moments and settlements were evaluated for both the cases and compared to those obtained from the conventional method of analysis of annular raft foundation. It is found that the responses in raft vary considerably depending on the stiffness of the underlying soil and the stiffness of foundation. Piled raft foundations are better suited for tall chimneys to be constructed in loose or medium sand. © 2017, The Institution of Engineers (India).Item Stress Distribution in Basal Geogrid Reinforced Pile-Supported Embankments Under Seismic Loads(Springer, 2021) Patel, R.M.; Jayalekshmi, B.R.; Shivashankar, R.Basal geosynthetic reinforced pile-supported embankments are proven as the more appropriate ground improvement technique for constructing embankments for roads over very soft clay deposits and approach roads or embankments to bridges. Numerous experimental and analytical works are available on the soil arching phenomenon of geosynthetic reinforced piled embankments subjected to static loading conditions. This study attempts to evaluate the stress distribution and soil arching in geosynthetic reinforced pile-supported embankments subjected to seismic excitations. Time-history analysis has been performed on the basal geogrid reinforced pile-supported embankments by varying the height of embankment and tensile modulus of geogrid. Analyses of results show that for ? (the ratio of height of embankment to pile centre to centre spacing) less than or equal to 4.5, a geogrid tensile modulus of 3000 kN/m is sufficient to withstand vertical stresses due to earthquakes. And for the considered embankment height and pile diameter when ? nearly equal to 4.5, differential settlements are very less irrespective of seismic excitations. © 2021, The Author(s), under exclusive licence to Springer Science+Business Media, LLC part of Springer Nature.Item Pore Water Pressure Analysis in Coir Mat-Reinforced Soil Incorporating Soil-Structure Interaction(Springer Science and Business Media Deutschland GmbH, 2022) Sreya, M.V.; Jayalekshmi, B.R.; Venkataramana, K.The proposed study investigates the effectiveness of reinforcing the soft soil by a coir mat, a natural material, to act as a seismic soil-isolation medium. A 3D finite element simulation in PLAXIS 3D software has been carried out on models of five-storey buildings resting on raft foundations in soft soil with and without the soil-isolation mechanism. This study also deals with the coir composites, coir–polyethylene and coir–rubber were proposed to increase the durability of the coir mat. The isolated soil-structure system was exposed to four different earthquake motions, such as the ground motions corresponding to the elastic design spectrum for Zone III as per the Indian standard code (IS 1893 (Part 1): 2016), the scaled Northridge earthquake (1994), El Centro earthquake (1940) and Chi-Chi earthquake (1999). A pore water pressure analysis of soil bed has been carried out to study the efficacy of these materials to reduce the excess pore water pressure generated in soil under earthquake loading. The other parameters, such as shear strain mobilized shear strength, effective stress in soil, and roof acceleration, in the building were analyzed. Isolation efficiencies of reinforcement materials to reduce the excess pore water pressure generated in soil under different earthquake motions obtained are 75–82%, 71–80% and 67–72% with coir, coir–polyethylene and coir–rubber, respectively. The resulting shear strain in soil reinforced by isolation mats is lower than that in unreinforced soil because the isolation mats strengthen the soil. Compared to the unreinforced soil, the mobilized shear strength and effective stress in the soil are increased when it is reinforced with coir and coir composites. The roof acceleration and bottom acceleration in the building got reduced by the isolation mechanism. © 2022, The Author(s), under exclusive licence to Springer Nature Switzerland AG.Item Effect of Coir Reinforced Soil on the Seismic Response of RC Framed Buildings(Springer, 2022) Sreya, M.V.; Jayalekshmi, B.R.; Venkataramana, K.This study examines the effectiveness of reinforcing the soil with coir mat, a natural material, to act as a seismic soil-isolation medium. A 3D finite element simulation has been carried out on models of five-storey buildings resting on raft foundations in soft and stiff soil with and without the soil-isolation mechanism. The optimum values of the parameters such as the depth of embedment, width, and thickness of the coir mat have been analyzed. The isolated soil-structure system was exposed to two different earthquake motions, such as El Centro (1940) and simulated seismic excitation corresponds to the elastic design spectrum for Zone III as per the Indian Standard code (IS 1893 (Part 1): 2016). The optimum value for the depth of embedment, width, and thickness of the coir mat was identified as B/18, B/0.45 and B/36. The proposed study also deals with the coir (C) mat composited with other isolation materials such as polyethylene (PE) foam, rubber (RU) mat and geomembrane (G) to form C-PE, C-RU and C-G mats. These composites were proposed to increase the durability of the coir mat. The reinforcement of the C-PE mat shows a maximum of about 30% reduction in roof acceleration and 68% reduction in contact pressure. A pore water pressure analysis of soil bed also has been carried out to study the efficacy of these materials to reduce the excess pore water pressure generated in soil under earthquake loading. For that, a simple soft soil is modelled in Cyclic 1D software with and without the soil-isolation mechanism. The soil bed was exposed to El Centro (1940) and Northridge (1994) input motions. C-PE mat significantly reduces the excess pore water pressure by almost 93% and 88% in soil under El Centro and Northridge input motions, respectively. © 2022, Indian Geotechnical Society.