Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Effect of zinc and rare-earth element addition on mechanical, corrosion, and biological properties of magnesium(Cambridge University Press, 2018) Kottuparambil, R.R.; Bontha, S.; Ramesh, M.R.; Arya, S.; Jana, A.; Das, M.; Balla, V.K.; Amrithalingam, S.; Prabhu, T.R.The present work aims to understand the effect of zinc and rare-earth element addition (i.e., 2 wt% Gd, 2 wt% Dy, and 2 wt% of Gd and Nd individually) on the microstructure evolution, mechanical properties, in vitro corrosion behavior, and cytotoxicity of Mg for biomedical application. The microstructure results indicate that the Mg-Zn-Gd alloy consists of the lamellar long period stacking ordered phase. The electrochemical and immersion corrosion behavior were studied in Hanks balanced salt solution. Enhanced corrosion resistance with reduced hydrogen evolution volume and magnesium (Mg2+) ion release were estimated for the Mg-Zn-Gd alloy as compared to the other two alloy systems. At the early stage of corrosion, formation of the oxide film inhibited the corrosion propagation. However, at the later stages, the breaking of the oxide film leads to shallow pitting mode of corrosion. The ultimate tensile strength of Mg-Zn-Gd-Nd is better than the other two alloys due to the uniform distribution of the Mg12Nd precipitate phase. The moderate strength in the Mg-Zn-Gd alloy is due to the low volume fraction of the secondary phase. The MTT (methylthiazoldiphenyl-tetrazolium bromide) assay study was carried out to understand the cell cytotoxicity on the alloy surfaces. Studies revealed that all three alloys had significant cellular adherence and no adverse effect on cells. © 2018 Materials Research Society.Item Comparative investigation of coating and friction stir processing on Mg-Zn-Dy alloy for improving antibacterial, bioactive and corrosion behaviour(Elsevier B.V., 2021) Rokkala, U.; Jana, A.; Bontha, S.; Ramesh, M.R.; Balla, V.K.Magnesium based alloys are well-known materials for temporary implant applications. However, failures due to early degradation and bacterial infection are limiting their applications. To overcome these problems, in the present work a Mg-Zn-Dy alloy based composite surface was prepared using coating and friction stir processing (FSP) techniques. Herein, hydroxyapatite (HA) and silver (Ag) particles were deposited on Mg-Zn-Dy alloy to obtain HA and Ag coated surface (C-HAg). Later, FSP was carried out on the C-HAg surface to develop a Mg-Zn-Dy alloy based composite surface (F-HAg). Field emission scanning electron microscope (FESEM) and energy dispersive X-ray analysis (EDS) confirm the mixing of HA and Ag particles with the Mg-Zn-Dy substrate. Antibacterial studies reveal that both C-HAg and F-HAg samples inhibit Escherichia coli and Staphylococcus aureus bacteria. In vitro cytotoxicity study indicates that the both samples are non-toxic in nature. Results of in vitro corrosion study reveal a significant reduction (72%) in corrosion rate of F-HAg sample when compared to C-HAg sample. The F-HAg samples showed simultaneous improvement in corrosion resistance and antibacterial properties with good biocompatibility. The results of this study indicate that the developed composite surface is a promising material for antibacterial and biodegradable implant applications. © 2021 Elsevier B.V.Item Selective oxidation of biomass-derived furfural to 2(5H)-furanone using trifluoroacetic acid as the catalyst and hydrogen peroxide as a green oxidant(Springer Science and Business Media Deutschland GmbH, 2023) Bhat, N.S.; Kumar, R.; Jana, A.; Mal, S.S.; Dutta, S.In this work, biomass-derived furfural has been selectively oxidized to 2(5H)-furanone using aqueous hydrogen peroxide as the green oxidant. Among various homogeneous acid catalysts screened for the transformation, trifluoroacetic acid (TFA) was found to be the most suitable candidate that afforded up to 52% isolated yield of 2(5H)-furanone under mild conditions (RT, 1 h). In addition, succinic acid was recovered in nearly 20% yield from the aqueous layer. The organic solvent-free, gram-scale reaction was optimized on temperature, the molar ratio of H2O2 and furfural, and the amount of TFA used. [Figure not available: see fulltext.]. © 2021, The Author(s), under exclusive licence to Springer-Verlag GmbH, DE part of Springer Nature.Item Efficient Preparation of the Esters of Biomass-Derived Isohexides by Base-Catalyzed Transesterification under Solvent-Free Conditions(American Chemical Society, 2023) Bhat, N.S.; Vinod, N.; Tarafder, K.; Nayak, M.K.; Jana, A.; Mal, S.S.; Dutta, S.The monoesters and diesters of glucose-derived isosorbide (IS) have potential applications as sustainable dispersants, surfactants, emulsifiers, monomer units for polymers, and plasticizers. This work reports a solvent-free, high-yielding, and scalable pathway for producing the monoesters and diesters of IS by a transesterification reaction using K2CO3 as an efficient, inexpensive, and recyclable base catalyst. In the case of monoesters, the selectivity toward the exo-monoester of IS was found higher than that toward the endo-monoester. The methodology was successfully extended to synthesize the monoesters and diesters of isomannide and isoidide. The gram-scale preparation of alkyl, vinyl, and aryl esters of isohexides was optimized on the reaction temperature, duration, equivalence of the ester reagent, and catalyst loading. Under optimized conditions (50 mol % K2CO3, 180 °C, 6 h), various aryl and alkyl esters of the isohexides were isolated in satisfactory yields. The unsymmetrical diesters of the isohexides were conveniently synthesized by stepwise transesterification. © 2023 American Chemical Society.