Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Synthesis, characterization and desalination study of novel PSAB and mPSAB blend membranes with Polysulfone (PSf)(2012) Padaki, M.; Isloor, A.M.; A.F., A.F.; Abdullah, M.S.The present paper describes the synthesis of poly sulphonyl amino benzamide (PSAB) and methyalated poly sulphonyl amino benzamide (mPSAB) polymer, using terephthalic acid chloride and substituted 4-amino-1-benzensulphonmide in N-methyl-. 2-pyrrolidone. Polymers were characterized by FT-IR, NMR and GPC. Polysulfone composite membranes were prepared using these novel poymers by DIPS (Diffusion Induced Phase Seperation) method. These composite membranes are useful for water purification with special emphasis on sea water desalination. Newly prepared membranes were studied for salt rejection, water flux, molecular weight cut off by PEG solution, effect of the pH on water swelling and salt rejection and flux decline was also studied. 30 to 70% of the salt rejection was observed in all membranes. Effect of the dilution on salt rejection was studied using different concentration of NaCl solution varying from 1000. ppm to 3500. ppm. All the membranes showed 80% rejection for PEG having 1000. Da molecular weight. Contact angle and water swelling was measured to determine hydrophilicity of the membrane. Water swelling and salt rejection in different pH was also studied. © 2012 Elsevier B.V.Item Preparation and characterization of sulfonated polysulfone and N-phthloyl chitosan blend composite cation-exchange membrane for desalination(2012) Padaki, M.; Isloor, A.M.; Wanichapichart, P.; A.F., A.F.Sulfonated polysulfone (sPSf) was prepared and used as a polymer matrix for cation-exchange membranes (CEM). The sulfonation reaction was carried out at room temperature and the degree of sulfonation was calculated by titration method. Blend composite membranes were prepared using different ratios of sPSf and modified chitosan (CS). Membrane properties were studied in terms of water flux, water swelling ratio, molecular weight cut off (MWCO), ion-exchange capacity (IEC) and contact angle measurement. Charge on the membrane was confirmed by ionic diffusion potential (DP). It was observed that, DP increased with the increase in the concentration of sPSf. The membrane sPSf:CS 60:40 showed 1000Da MWCO, 14.6mV diffusion potential (DP) and 0.083mM/g of IEC. Similarly sPSf:CS 90:10 showed 10,000Da MWCO, 71.7mV diffusion potential (DP) and 0.176mM/g of IEC. Moreover, membrane sPSf:CS 60:40 showed 93%, 89% and 69% for MgSO 4, Na 2SO 4 and NaCl rejection respectively. © 2012 Elsevier B.V.Item Preparation and characterization of PPEES/chitosan composite nanofiltration membrane(2013) Shenvi, S.S.; Abdul Rashid, S.A.; A.F., A.F.; Kassim, M.A.; Isloor, A.M.Composite membrane having chitosan (CH) as the active layer supported on Poly(1,4-phenylene ether ether sulfone) (PPEES) membrane was synthesized in the current study. The chitosan layer was crosslinked by glutaraldehyde in two different concentrations. The scanning electron microscopic images and hydraulic permeability coefficient revealed the ultrafiltration (UF) nature of the neat PPEES membrane. This was used as a new support material for the casting of chitosan layer in order to get composite membranes. The composite nature of the PPEES/CH membranes was confirmed by FESEM and DSC analysis. The Infrared spectroscopy results confirmed the crosslinking of the chitosan surface by glutaraldehyde (GA). The changes in the hydrophobic nature of the PPEES membrane surface due to deposition of chitosan active layer followed by crosslinking were studied by their contact angle measurement and water flux study. From our studies, PPEES has proved to be a good support membrane for preparation of composite membranes. Increase in GA concentration increased the salt rejection of the membrane up to 34% for NaCl and 53% for MgSO4 on one hand with a simultaneous decrease in the flux values. The hydraulic permeability coefficient values confirmed that the prepared membranes are in nanofiltration range. © 2012 Elsevier B.V.Item Preparation and characterization study of PPEES/chitosan composite membrane crosslinked with tripolyphosphate(Elsevier, 2014) Shenvi, S.; A.F., A.F.; Isloor, A.M.A novel composite membrane was prepared using chitosan (CH) as the active layer supported on a Poly(1,4-phenylene ether ether sulfone) (PPEES) membrane. The chitosan layer was ionically cross linked with sodium tripolyphosphate (TPP). The composite nature of PPEES/CH membranes was confirmed by Scanning Electron Microscopy (SEM). Infrared (IR) spectroscopy results and SEM-EDX analysis confirmed the crosslinking of chitosan surface with TPP. The membranes exhibited higher crosslinking density in acidic media than in basic media. The changes in the hydrophobic nature of PPEES membrane surface due to deposition of chitosan active layer followed by crosslinking were studied by their contact angle measurement, water flux and water uptake studies. The membranes showed rejection up to 55% and 21% towards MgSO4 and NaCl respectively at pH=5 and a flux recovery ratio of 73%. © 2014 Elsevier B.V.Item Preparation and characterization of novel PSf/PVP/PANI-nanofiber nanocomposite hollow fiber ultrafiltration membranes and their possible applications for hazardous dye rejection(Elsevier, 2015) Kajekar, A.J.; Dodamani, B.M.; Isloor, A.M.; Zulhairun, A.K.; Cheer, N.B.; A.F., A.F.; Shilton, S.J.In the present study, PANI (polyaniline)-nanofibers were synthesized by interfacial polymerization technique, dispersed in n-Methyl-2-Pyrrolidone (NMP) solvent and blended with PVP (Polyvinylpyrrolidone)/PSf (Polysulfone) for preparing the novel hollow fiber membrane by dry-wet spinning technique. The newly prepared nanocomposite ultrafiltration hollow fiber membrane is characterized by Scanning Electron Microscope (SEM), Contact Angle, Zeta Potential and Differential Scanning Calorimeter (DSC). Filtration studies are conducted to measure the membrane pure water flux (PWF), rejection of hazardous dye (Reactive Red 120) and fouling resistance. The maximum rejections are obtained for M 0.5 membrane with 99.25% rejection of RR120 hazardous dye at 2. bar pressure. The pure water flux, percentage rejection, antifouling property and thermal resistance increased with an increase in PANI-nanofiber concentration. The contact angle of the membrane decreased with increasing PANI-nanofiber concentration, which indicated increased hydrophilicity of the new membranes. © 2015 Elsevier B.V.