Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Permeation, Antifouling and desalination performance of TiO2 nanotube incorporated PSf/CS blend membranes(2013) Kumar, R.; Isloor, A.M.; A.F., A.F.; Abdul Rashid, S.A.; Ahmed, A.A.Polysulfone (PSf) and chitosan (CS) blend membranes were prepared by incorporating titanium dioxide nanotubes (TiO2NT) in different compositions. The proper blending of PSf and CS in the PSf/CS/TiO2 membranes was confirmed by ATR-IR spectroscopy. The influence of nanotubes on morphology of membranes was investigated by Field Emission Scanning Electron Microscopy (FESEM). The effect of nanotubes on hydrophilicity of the membranes was studied by water swelling and contact angle measurements. The distribution of TiO2NT on the membrane surface was determined by Transmission Electron Microscope (TEM) analysis. The permeation property of PSf/CS/TiO2NT membranes was carried out by measuring the time dependent pure water flux (PWF). Bovine serum albumin (BSA) protein rejection studies were performed to know the antifouling properties. The rheological percolation threshold of PSf/CS/TiO2NT solutions was measured by viscosity studies. The nanotubes incorporated PSf/CS membranes showed enhanced permeation and antifouling properties compared to PSf/CS and nascent PSf ultrafiltration membranes. Membranes prepared well above rheological percolation threshold showed drastic reduction in pore size and acted as nanofiltration (NF) membranes. © 2013 Elsevier B.V.Item Preparation and performance studies of polysulfone-sulfated nano-titania (S-TiO2) nanofiltration membranes for dye removal(Royal Society of Chemistry, 2015) Pereira, V.R.; Isloor, A.M.; Bhat, K.U.; A.F., A.F.; AlObaid, A.; Fun, H.-K.Polysulfone nanofiltration membranes containing sulfated nano-titania (S-TiO2) were fabricated, with the aim to enhance the membrane properties along with the possible rejection of Methylene Blue (MB) dye by membranes. Initially S-TiO2 was synthesized from nano TiO2 by the action of sulfuric acid. The synthesized S-TiO2 was characterized by Fourier Transform Infrared spectroscopy (FT-IR), Energy Dispersive Spectrophotometry (EDS) and Transmission Electron Microscopy (TEM) analysis. S-TiO2 was added in increasing concentrations into the membranes and its effect on the performance of the membranes was evaluated. The synthesized membranes were characterized by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). Polysulfone membranes containing S-TiO2 showed enhancement in properties in terms of hydrophilicity, water uptake, mechanical strength, improved pure water flux (PWF), antifouling nature and high Flux Recovery Ratio (FRR). The polysulfone membranes with S-TiO2 showed 99% rejection for BSA (Bovine Serum Albumin) protein molecules during BSA filtration. The prepared membranes were used for the removal of MB dye from aqueous solutions. A maximum of 90.4% rejection was obtained for MB for the membrane having 2.0 wt% of S-TiO2 under UV light radiation. This approach showed that polysulfone-S-TiO2 membranes displayed good efficiency for dye removal and can be effectively used for the removal of MB dye from aqueous solutions under suitable conditions. © The Royal Society of Chemistry.Item Preparation of polysulfone-based PANI-TiO2 nanocomposite hollow fiber membranes for industrial dye rejection applications(Royal Society of Chemistry, 2016) Pereira, V.R.; Isloor, A.M.; Zulhairun, A.K.; Subramaniam, M.N.; Lau, W.J.; A.F., A.F.Polysulfone-based polyaniline-TiO2 containing hollow fiber membranes were prepared via a dry wet spinning method. Polyaniline (PANI) coated TiO2 nanotubes were prepared via chemical oxidative polymerisation and were incorporated into the hollow fiber membranes at different compositions. The hollow fibers were fabricated by varying the air gap distance during the spinning process. The effects of the addition of PANI coated TiO2 and the variation in the air gap distance on membrane performance, such as morphology and the permeability of the membranes, were analysed. The addition of the PANI-TiO2 nanocomposite enhanced the hydrophilicity and antifouling ability of the prepared membranes. The polysulfone hollow fiber membranes were examined for their dye rejection of Reactive Black 5 and Reactive Orange 16. The results indicated that the polysulfone hollow fibers containing 1.0 wt% of PANI-TiO2 fabricated using a 5 cm air gap can be used as a potential candidate for industrial dye rejection and showed a maximum rejection of 81.5% and 96.5% for Reactive Black 5 and Reactive Orange 16, respectively. © 2016 Royal Society of Chemistry.Item Photoreactor-ultrafiltration hybrid system for oily bilge water photooxidation and separation from oil tanker(Elsevier, 2016) Moslehyani, A.; Mobaraki, M.; Isloor, A.M.; A.F., A.F.; Othman, M.H.D.A novel design of hybrid system consisting of photoreactor (PR) combined with ultrafiltration (UF) membrane was investigated for oily bilge water degradation and separation from oil tanker. Initially, the bilge organic compounds were photooxidized using ultraviolet type A (UVA) light irradiation on 100, 200 and 300 ppm of TiO2. Further TiO2 and oxidized oily bilge water was filtered using hollow fiber membrane separator, which was prepared by polyvinylidene fluoride (PVDF) and halloysite nanotubes. The hollow fiber membranes were characterized by ATR-IR spectrum, thermal gravimetric analysis (TGA), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and X-ray photoelectron spectroscope (XPS). Individual hydrocarbon of oily bilge water was identified by using gas chromatography-mass spectrometry (GC-MS) analysis. According to the GC-MS analysis, over 90% decomposition of oil in bilge water has occurred by 200 and 300 ppm of TiO2 suspension. On the other hand, pH meter showed that, decomposed oily bilge water was more acidic, which increased to pH 7 after UF system process. Moreover, over 99% of degraded oil in bilge water was filtered by this promising hybrid system. © 2016 Elsevier B.V. All rights reserved.Item Novel mixed matrix membranes incorporated with dual-nanofillers for enhanced oil-water separation(Elsevier B.V., 2017) Lai, G.S.; Yusob, M.H.M.; Lau, W.J.; Jamshidi Gohari, R.J.; Emadzadeh, D.; A.F., A.F.; Goh, P.S.; Isloor, A.M.; Arzhandi, M.R.-D.In this work, a new type of mixed matrix membranes (MMMs) composed of dual-nanofillers at different ratios of hydrous manganese oxide (HMO) and titanium dioxide (TiO2) was fabricated with the objective of improving properties of polyethersulfone (PSF)-based membrane for oil-water separation process. The morphology and surface chemistry of the resultant MMMs were characterized by several analytical instruments, i.e., SEM-EDX, contact angle goniometer and FTIR spectrometer prior to separation performance evaluation using oily solution composed of 500 or 2000 ppm. The results showed that the membrane surface hydrophilicity was greatly improved upon addition of hydrophilic nanofillers and HMO in particular showed greater extent of hydrophilicity enhancement owing to the fact that it is associated with higher amount of [sbnd]OH functional groups compared to TiO2. The improved surface hydrophilicity coupled with formation of long finger-like voids in the membrane structure are the main factors leading to greater water flux of MMMs in comparison to control PES membrane. MMM2 (membrane made of HMO:TiO2ratio of 0.75:0.25) and MMM4 (HMO:TiO2ratio of 0.25:0.75) in particular were the best two performing nanofillers-incorporated membranes owing to their good balance between water flux and oil removal rate. They achieved 31.73% and 26.41% higher water flux than that of the control membrane without sacrificing oil removal rate. Most importantly, these nanofillers-incorporated membranes showed significantly lower degree of flux decline as a result of improved surface resistance against oil fouling and are of potential for long-term operation with extended lifespan. © 2017 Elsevier B.V.Item Synthesis and characterization of titanium dioxide hollow nanofiber for photocatalytic degradation of methylene blue dye(MDPI AG, 2021) Jafri, N.N.M.; Jaafar, J.; Alias, N.H.; Samitsu, S.; Aziz, F.; Salleh, W.N.W.; Mohd Yusop, M.Z.M.; Othman, M.H.D.; Rahman, M.A.; A.F., A.F.; Matsuura, T.; Isloor, A.M.Environmental crisis and water contamination have led to worldwide exploration for advanced technologies for wastewater treatment, and one of them is photocatalytic degradation. A one?dimensional hollow nanofiber with enhanced photocatalytic properties is considered a promising material to be applied in the field. Therefore, we synthesized titanium dioxide hollow nanofibers (THNF) with extended surface area, light?harvesting properties and an anatase–rutile heterojunction via a template synthesis method and followed by a calcination process. The effect of calcination temperature on the formation and properties of THNF were determined and the possible mechanism of THNF formation was proposed. THNF nanofibers produced at 600 °C consisted of a mixture of 24.2% anatase and 75.8% rutile, with a specific surface area of 81.2776 m2/g. The hollow nanofibers also outperformed the other catalysts in terms of photocatalytic degradation of MB dye, at 85.5%. The optimum catalyst loading, dye concentration, pH, and H2O2 concentration were determined at 0.75 g/L, 10 ppm, pH 11, and 10 mM, respectively. The highest degradation of methylene blue dye achieved was 95.2% after 4 h of UV irradiation. © 2021 by the authors. Licensee MDPI, Basel, Switzerland.