Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Synthesis, characterization & impedance studies of some new nano filtration membranes(Trans Tech Publications Ltd ttp@transtec.ch, 2010) Padaki, M.; Hegde, C.; Isloor, A.M.In the recent years membrane technology has gained significant attention from polymer chemists all around the world due to their attractive features such as efficiency, low costs, low energy costs and as effective solutions to longstanding problems in the chemical industries. Membrane technologies have been widely applied in the separation of liquids and even gases. Many separation problems can be solved economically by nanofiltration alone or in combination with other separation processes. This study aimed to synthesize polysulfone based nanofiltration membranes using DIPS (diffusion induced phase separation) technique. Newly synthesized polymer membranes were subjected to Infra red spectral and water uptake studies. Membranes were also characterized using electrochemical spectroscopy for their proton conducting property. Their surface morphology is visualized by SEM. © (2010) Trans Tech Publications.Item Synthesis, characterization and desalination study of composite NF membranes of novel Poly[(4-aminophenyl)sulfonyl]butanediamide (PASB) and methyalated Poly[(4-aminophenyl)sulfonyl]butanediamide (mPASB) with Polysulfone (PSf)(2013) Padaki, M.; Isloor, A.M.; Kumar, R.; A.F., A.F.; Matsuura, T.In the present investigation, Poly [(4-aminophenyl)sulfonyl]butanediamide (PASB) and methylated Poly[(4-aminophenyl)sulfonyl] butanediamide (mPASB) polymers were synthesized, using succinyl chloride and substituted 4-amino-1-benzenesulphonamide. Polysulfone composite membranes were prepared by blending these novel polymers by Diffusion Induced Phase Separation (DIPS) method. The performance of the membrane was studied in terms of salt rejection, water flux and molecular weight cutoff. The prepared membranes were hydrophilic in nature, which was confirmed by water uptake studies and contact angle measurement. All the membranes showed 1000. Da molecular weight cutoff. A maximum NaCl rejection of 52% was observed in some of the membranes. The effect of feed NaCl concentration on the NaCl rejection was also studied. The resistance of the membranes in a wide pH range was studied by water uptake measurement. Antifouling properties of the membranes were also performed using Bovine Serum Albumin (BSA) solution. © 2012 Elsevier B.V.Item Polysulfone-Chitosan blend ultrafiltration membranes: Preparation, characterization, permeation and antifouling properties(2013) Kumar, R.; Isloor, A.M.; A.F., A.F.; Abdul Rashid, S.A.; Matsuura, T.Biocompatible and naturally occurring chitosan was used as an additive for the preparation of a polysulfone ultrafiltration membrane. Two different compositions of polysulfone in N-methylpyrrolidone (NMP) and chitosan in 1% acetic acid were blended to prepare PSf-CS ultrafiltration membranes by the diffusion induced phase separation (DIPS) method. The proper blending of polysulfone and chitosan in PSf-CS membranes was confirmed by ATR-IR analysis. The surface and cross-sectional morphology of the membranes was studied by scanning electron microscopy (SEM). The membrane hydrophilicity was determined by water uptake and contact angle measurements. The PSf-CS membrane showed an enhanced hydrophilicity compared to a PSf ultrafiltration membrane. The time dependent permeation studies revealed the improved flux of PSf-CS membranes. PSf-CS membranes were subjected to bovine serum albumin (BSA) protein rejection studies. An improved antifouling property was observed for PSf-CS blend membranes as compared to pristine PSf ultrafiltration membranes. Both the permeation and antifouling properties of PSf-CS membranes increased with an increase in chitosan composition. © 2013 The Royal Society of Chemistry.Item Synthesis and characterization of novel sulfanilic acid-polyvinyl chloride-polysulfone blend membranes for metal ion rejection(Royal Society of Chemistry, 2016) Nayak, V.; Jyothi, M.S.; Balakrishna, R.G.; Padaki, M.; Isloor, A.M.Near-complete removal of heavy metals, namely Cd(ii), Cr(vi) and Pb(ii), has been attempted by a membrane purification process using a blend of modified polyvinyl chloride (PVC) and polysulfone (PSf), prepared by the diffusion induced phase separation (DIPS) method. The prepared novel material was characterized by NMR, ATR-IR spectroscopy and DSC. The sulphonyl groups incorporated into PVC enhance the hydrophilicity and are substantiated by water uptake, contact angle (CA) and flux studies. The obtained properties of the blend membrane like increased surface roughness and porosity are observed from AFM and SEM analysis. An enhanced rejection of ?95% which is about 1.15, 1.41 and 1.37 times better than the commercially available NF 270 membrane was observed, for Cd(ii), Cr(vi) and Pb(ii) respectively. The work was further extended to study the antifouling property and the interference of other existing metal ions on the performance. An improved antifouling property with 98.5% rejection for bovine serum albumin (BSA) and a 75.6% flux recovery ratio (FRR) was achieved. The study gains significance in exploring the incorporation of sulphonyl groups in to polymers, to enhance membrane performance. © The Royal Society of Chemistry 2016.Item Fabrication of novel PPSU/ZSM-5 ultrafiltration hollow fiber membranes for separation of proteins and hazardous reactive dyes(Taiwan Institute of Chemical Engineers, 2018) Nayak, M.C.; Isloor, A.M.; Moslehyani, A.; Ismail, N.; A.F., A.F.Polyphenylsulfone (PPSU) based asymmetric hollow fiber membranes were prepared by the addition of different percentages of ZSM-5 particles by diffusion induced phase separation method. Polyvinylpyrrolidone (PVP) was used as a pore forming agent. The fabricated membranes were characterized by Field Emission scanning electron microscopy (FESEM), Energy Dispersive Spectroscopy (EDS), contact angle, water permeability, water uptake and by porosity measurements. Membranes filtration study was performed using different proteins namely bovine serum albumin (BSA), egg albumin (EA) and hazardous dyes like Reactive black 5 (RB-5), Reactive orange 16 (RO-16) in aqueous solutions. It was found that, addition of ZSM-5 in membrane matrix showed better dye removal capacity because of its hydrophilic and adsorptive nature. The membrane (PZ-3) with higher loading of additive exhibited rejection percentages of 100% for BSA, 95.23% for EA proteins and with reactive dyes 90.81% for RB-5 and 82.84% for RO-16 as compared to the pristine HF membrane. © 2017 Taiwan Institute of Chemical EngineersItem Novel polyphenylsulfone (PPSU)/nano tin oxide (SnO2) mixed matrix ultrafiltration hollow fiber membranes: Fabrication, characterization and toxic dyes removal from aqueous solutions(Elsevier B.V., 2019) Nayak, M.C.; Isloor, A.M.; Siddique, I.; Balakrishna Prabhu, B.; Ismail, N.I.; Asiri, A.M.Novel polyphenylsulfone (PPSU)/nano tin oxide (SnO2) mixed matrix hollow fiber membranes (HFMs) were fabricated by dry-wet spinning via phase separation method. In the current research, reported the contrast between neat PPSU membrane and nanocomposite membranes (PPSU/SnO2), to determine the toxic reactive dyes namely, reactive black-5 (RB-5) and reactive orange-16 (RO-16) removal ability from the aqueous media. Scanning electron microscopy (SEM) was used to observe the HFMs cross-sectional morphological changes and surface roughness parameters of membranes were analyzed using atomic force microscopy (AFM). The surface wettability ability of HFMs was examined with a contact angle, water uptake, and porosity measurements. The cross-flow filter unit was engaged to quantify the water permeability, anti-fouling ability as well as the dye rejection ability of fabricated membranes. With increasing the SnO2 NPs wt% in PPSU polymer matrix the membrane performance was enhanced continuously, it became evident that the incorporated SnO2 NPs plays main role in membrane performance. Added, water-soluble poly (vinylpyrrolidone) (PVP) can also impact the pore morphology in membranes. At the end, PS-3 membrane exhibited lower contact angle (63.7 0), higher water uptake (74.8%), porosity (84.1%), pure water flux 362.9 L/m2 h, and high potential for dyes rejection application, of about >94% for RB-5, and >73% for RO-16 dye, respectively. From the preliminary results, it can be stated that the usage of SnO2 NPs in membrane technology become effective towards wastewater treatment. © 2019 Elsevier B.V.Item Improved separation of dyes and proteins using membranes made of polyphenylsulfone/cellulose acetate or acetate phthalate(Springer Science and Business Media Deutschland GmbH, 2020) Kumar, M.; Isloor, A.M.; Todeti, S.R.; Gnani Peer Mohamed, G.P.S.; Siddique, I.; A.F., A.F.; Asiri, A.M.Industrial wastewater often contains xenobiotics such as heavy metals, dyes and proteins, yet there is a lack of efficient cleaning methods. Therefore, here we fabricated hollow fiber membranes using polyphenylsulfone containing 1, 3 and 5 wt% of cellulose acetate and cellulose acetate phthalate by non-solvent induced phase separation. Membrane morphology was characterized by field emission scanning electron microscopy. The hydrophilicity of the membranes was measured by contact angle, water uptake and porosity measurement. The thermal miscibility of the membrane with additives was assessed by thermogravimetric analysis. Hollow fiber membranes were tested for separation of azo dyes, e.g., reactive orange 16 and reactive black 5, and of proteins: bovine serum albumin, egg albumin and pepsin. Results show increasing rejection of dyes and proteins with the content of cellulose acetate and cellulose acetate phthalate. Water permeability was 41.26 L/m2 h bar for the polyphenylsulfone membrane, 64.47 L/m2 h bar for the polyphenylsulfone/5 wt% cellulose acetate membrane and 72.60 L/m2 h bar for the polyphenylsulfone/5 wt% cellulose acetate phthalate membrane. © 2020, Springer Nature Switzerland AG.Item New preparation methods for pore formation on polysulfone membranes(MDPI AG, 2021) Vainrot, N.; Li, M.; Isloor, A.M.; Eisen, M.S.This work described the preparation of membranes based on aromatic polysulfones through the phase-inversion method induced by a nonsolvent, generating the phase separation (NIPS) process. Three new techniques, including the nano iron acid etching method, base hydrolysis method of crosslinked polymers, and base hydrolysis method of a reactive component in a binary polymer blend, were developed for pore creation on membranes. The modified polymers and obtained membranes were carefully characterized. The uniform pores were successfully created by base hydrolysis of the crosslinked polymers and obtained at the size of the crosslinker. Moreover, homogeneous pores were created after base hydrolysis of the membranes prepared from binary polymer blends due to the internal changes in the polymer structure. The separation performance of membranes was tested with different inorganic salt solutions and compared with commercially known membranes. These new membranes exhibited high water flux (up to 3000 L/m?2·h?1 at 10 bar and at 25?C) and reasonable rejections for monovalent (21–44%) and multivalent ions (18–60%), depending on the different etching of the hydrolysis times. The comparison of these membranes with commercial ones confirmed their good separation performance and high potential application for water treatment applications. © 2021 by the authors. Licensee MDPI, Basel, Switzerland.