Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Permeation, Antifouling and desalination performance of TiO2 nanotube incorporated PSf/CS blend membranes(2013) Kumar, R.; Isloor, A.M.; A.F., A.F.; Abdul Rashid, S.A.; Ahmed, A.A.Polysulfone (PSf) and chitosan (CS) blend membranes were prepared by incorporating titanium dioxide nanotubes (TiO2NT) in different compositions. The proper blending of PSf and CS in the PSf/CS/TiO2 membranes was confirmed by ATR-IR spectroscopy. The influence of nanotubes on morphology of membranes was investigated by Field Emission Scanning Electron Microscopy (FESEM). The effect of nanotubes on hydrophilicity of the membranes was studied by water swelling and contact angle measurements. The distribution of TiO2NT on the membrane surface was determined by Transmission Electron Microscope (TEM) analysis. The permeation property of PSf/CS/TiO2NT membranes was carried out by measuring the time dependent pure water flux (PWF). Bovine serum albumin (BSA) protein rejection studies were performed to know the antifouling properties. The rheological percolation threshold of PSf/CS/TiO2NT solutions was measured by viscosity studies. The nanotubes incorporated PSf/CS membranes showed enhanced permeation and antifouling properties compared to PSf/CS and nascent PSf ultrafiltration membranes. Membranes prepared well above rheological percolation threshold showed drastic reduction in pore size and acted as nanofiltration (NF) membranes. © 2013 Elsevier B.V.Item Fabrication of polydopamine functionalized halloysite nanotube/polyetherimide membranes for heavy metal removal(Royal Society of Chemistry, 2016) Hebbar, R.S.; Isloor, A.M.; Kulal, K.; A.F., A.F.Polydopamine modified halloysite nanotubes (HNTs) were synthesised through a one step facile procedure and employed as a well dispersed hydrophilic additive to enhance the filtration properties of polyetherimide (PEI) membranes. The nanocomposite membranes were prepared by an immersion precipitation method with different amounts of modified HNTs (MHNTs) in the casting solution. The good dispersion of MHNTs throughout the membrane matrix was confirmed by elemental mapping analysis. The prepared nanocomposite membranes were extensively studied in terms of their porosity, morphology, membrane hydraulic resistance and hydrophilicity. The permeation experiments showed that the modified membranes exhibited higher water flux than a pristine PEI membrane. The antifouling and anti-biofouling behaviour of the modified membranes was investigated in detail. The results revealed that a membrane with a 3 wt% MHNT dosage showed a higher Fouling Resistance Ratio (FRR) of 74.5% with reversible membrane fouling of 64.3%. Moreover, the membrane showed excellent resistance to microbial growth on the membrane surface. The well performing membrane was subjected to heavy metal ion rejection. Results indicated that membranes had the capacity to adsorb Pb2+ and Cd2+. Overall, PEI-MHNTs nanocomposite membranes could have great potential to improve antifouling, anti-biofouling and filtration properties. © The Royal Society of Chemistry 2016.Item Preparation of polysulfone-based PANI-TiO2 nanocomposite hollow fiber membranes for industrial dye rejection applications(Royal Society of Chemistry, 2016) Pereira, V.R.; Isloor, A.M.; Zulhairun, A.K.; Subramaniam, M.N.; Lau, W.J.; A.F., A.F.Polysulfone-based polyaniline-TiO2 containing hollow fiber membranes were prepared via a dry wet spinning method. Polyaniline (PANI) coated TiO2 nanotubes were prepared via chemical oxidative polymerisation and were incorporated into the hollow fiber membranes at different compositions. The hollow fibers were fabricated by varying the air gap distance during the spinning process. The effects of the addition of PANI coated TiO2 and the variation in the air gap distance on membrane performance, such as morphology and the permeability of the membranes, were analysed. The addition of the PANI-TiO2 nanocomposite enhanced the hydrophilicity and antifouling ability of the prepared membranes. The polysulfone hollow fiber membranes were examined for their dye rejection of Reactive Black 5 and Reactive Orange 16. The results indicated that the polysulfone hollow fibers containing 1.0 wt% of PANI-TiO2 fabricated using a 5 cm air gap can be used as a potential candidate for industrial dye rejection and showed a maximum rejection of 81.5% and 96.5% for Reactive Black 5 and Reactive Orange 16, respectively. © 2016 Royal Society of Chemistry.Item Efficient treatment of hazardous reactive dye effluents through antifouling polyetherimide hollow fiber membrane embedded with functionalized halloysite nanotubes(Taiwan Institute of Chemical Engineers, 2017) Hebbar, R.S.; Isloor, A.M.; Zulhairun, A.K.; Sohaimi Abdullah, M.; A.F., A.F.A simple, efficient and scalable approach was developed for the fabrication of highly fouling resistance nanocomposite hollow fiber membranes with the aim of effective removal of environmentally detrimental reactive dyes. The naturally occurring halloysite nanotubes were functionalized via facile self-polymerization of m-aminophenol in mild acidic condition and employed as a hydrophilic additive. The chemical modification was confirmed by FTIR, TEM and energy dispersed X-ray (EDX) analysis. The hybrid nanocomposite membrane was prepared by dry–wet spin technique with different additive dosage. The resultant membrane was characterized in terms of contact angle, surface energy, porosity, zeta potential, elemental mapping and morphology. The permeation experiments illustrated superior water flux of 104.9 Lm?1 h?1 and 9.6% of irreversible fouling with more than 90.3% of flux recovery by the simple hydraulic cleaning. Most importantly, prepared membrane was subjected for hazardous reactive dye removal application with different experimental parameters. The hybrid membrane with 2 wt. % of additive concentration showed more than 97% and 94% for the Reactive Red 102 and Reactive Black 5 dyes respectively. This approach may also be very useful in developing high flux, fouling resistant ultrafiltration hollow fiber membranes for the other similar type applications such as hemodialysis membranes. © 2017 Taiwan Institute of Chemical EngineersItem Fabrication of polyetherimide nanocomposite membrane with amine functionalised halloysite nanotubes for effective removal of cationic dye effluents(Taiwan Institute of Chemical Engineers, 2018) Hebbar, R.S.; Isloor, A.M.; Siddique, I.; Abdullah, M.S.; A.F., A.F.; Asiri, A.M.Naturally, occurring, low cost and eco-friendly halloysite nanotubes were chemically modified and uniformly immobilised into the polyetherimide membrane matrix with the aim of enhancing the properties and possible cationic dye rejection efficacy. The properties of fabricated nanocomposite membranes were examined by means of porosity, hydrophilicity, zeta potential and permeability. Permeation experiments revealed the enhanced water flux up to 195 L/m2h with 4 wt% additive dosage. The dye rejection efficacy of the prepared membranes was determined by using rhodamine B (Rh.B) and methylene blue (MB). The dye rejection studies were executed in terms of pH, contact time and initial dye concentration. The membrane with 4 wt% of nanomaterial dosage, showed rejection of 97% at pH 8 and 94% at pH 7 for MB and Rh.B dyes, respectively. Langmuir adsorption isotherm is the best model to explain interaction between dye molecules and membrane surface, with quantity of dye adsorbed (qmax) was observed to be 20.4 mg/g and 19.6 mg/g for MB and Rh.B, respectively. This approach showed modified membrane has good cationic dye rejection efficacy and can be efficiently employed to remove the dyes from aqueous streams. © 2018 Taiwan Institute of Chemical EngineersItem Nanohydroxyapatite Reinforced Chitosan Composite Hydrogel with Tunable Mechanical and Biological Properties for Cartilage Regeneration(Nature Publishing Group Houndmills Basingstoke, Hampshire RG21 6XS, 2019) Kumar, B.Y.S.; Isloor, A.M.; Mohan Kumar, G.C.M.; Siddique, I.; Asiri, A.M.With the continuous quest of developing hydrogel for cartilage regeneration with superior mechanobiological properties are still becoming a challenge. Chitosan (CS) hydrogels are the promising implant materials due to an analogous character of the soft tissue; however, their low mechanical strength and durability together with its lack of integrity with surrounding tissues hinder the load-bearing application. This can be solved by developing a composite chitosan hydrogel reinforced with Hydroxyapatite Nanorods (HANr). The objective of this work is to develop and characterize (physically, chemically, mechanically and biologically) the composite hydrogels loaded with different concentration of hydroxyapatite nanorod. The concentration of hydroxyapatite in the composite hydrogel was optimized and it was found that, reinforcement modifies the hydrogel network by promoting the secondary crosslinking. The compression strength could reach 1.62 ± 0.02 MPa with a significant deformation of 32% and exhibits time-dependent, rapid self-recoverable and fatigue resistant behavior based on the cyclic loading-unloading compression test. The storage modulus value can reach nearly 10 kPa which is needed for the proposed application. Besides, composite hydrogels show an excellent antimicrobial activity against Escherichia coli, Staphylococcus aureus bacteria’s and Candida albicans fungi and their cytocompatibility towards L929 mouse fibroblasts provide a potential pathway to developing a composite hydrogel for cartilage regeneration. © 2019, The Author(s).Item Polyphenylsulfone/multiwalled carbon nanotubes mixed ultrafiltration membranes: Fabrication, characterization and removal of heavy metals Pb2+, Hg2+, and Cd2+ from aqueous solutions(Elsevier B.V., 2020) Chandrashekhar Nayak, M.; Isloor, A.M.; Siddique, I.; Lakshmi, B.; Marwani, H.M.; Khan, I.Polyphenylsulfone/multiwalled carbon nanotubes/polyvinylpyrrolidone/1-methyl-2-pyrrolidone mixed matrix ultrafiltration flat-sheet membranes were fabricated via phase inversion process to inspect the heavy metals separation efficacy from aqueous media. Fabricated membranes cross-sectional morphological changes and the topographical alterations were assessed with Scanning electron microscopy (SEM) and atomic force microscopy (AFM). Particularly, MWCNTs assisted membranes exhibited better permeability ability as well as heavy metal removal enactment than virgin membrane. The dead-end filter unit was engaged in current research to examine the permeability and heavy metal removal competence of membranes. With the continuous enhancement of MWCNTs wt% in a polymer matrix, significant enhancement was observed with pure water flux study, from 41.69 L/m2 h to >185 L/m2 h as well as with the heavy metals separation study. Added additive MWCNTs can impact the pore sizes in membranes. The heavy metal separation results achieved, the membrane with 0.3 wt% of MWCNTs (PCNT-3) exhibited >98%, >76% and >72% for Pb2+, Hg2+ and Cd2+ ions, respectively. Overall, MWCNTs introduced PPSU membranes exposed best outcomes with heavy metals contained wastewater treatment. © 2019 The AuthorsItem Evaluation of the surface characteristics and antibacterial properties of Titanium dioxide nanotube and methacryloyloxyethylphosphorylcholine (MPC) coated orthodontic brackets-a comparative invitro study(Springer Science and Business Media Deutschland GmbH, 2024) Rao, M.; Ashith, M.V.; Suman, E.; Isloor, A.M.; Shetty, N.J.; Srikant, S.Objectives: White spot lesions are the most common iatrogenic effect observed during orthodontic treatment. This study aimed to compare the surface characteristics and antibacterial action of uncoated and coated orthodontic brackets. Materials and methods: Sixty commercially available stainless steel brackets were coated with TiO2 nanotubes and methacryloyloxyethylphosphorylcholine. The sample was divided into Group 1: uncoated orthodontic brackets, Group 2: Stainless steel brackets with TiO2 nanotubes coating, Group 3: Stainless steel brackets with methacryloyloxyethylphosphorylcholine coating, and Group 4: Stainless steel brackets with TiO2 nanotubes combined with methacryloyloxyethylphosphorylcholine coating. Surface characterization was assessed using atomic force microscopy and scanning electron microscopy. Streptococcus mutans was selected to test the antibacterial ability of the orthodontic brackets, total bacterial adhesion and bacterial viability were assessed. The brackets were subjected to scanning electron microscopy to detect the presence of biofilm. Results: The surface roughness was the greatest in Group 1 and least in Group 2 followed by Group 4 and Group 3 coated brackets. The optical density values were highest in Group 1 and lowest in Group 4. Comparison of colony counts revealed high counts in Group 1 and low counts in Group 4. A positive correlation between surface roughness and colony counts was obtained, however, was not statistically significant. Conclusions: The coated orthodontic brackets exhibited less surface roughness than the uncoated orthodontic brackets. Group 4 coated orthodontic brackets showed the best antibacterial properties. Clinical relevance: Coated orthodontic brackets prevent adhesion of streptococcus mutans and reduces plaque accumulation around the brackets thereby preventing formation of white spot lesions during orthodontic treatment. © The Author(s) 2024.