Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
48 results
Search Results
Item Carbon-based nanocomposite membranes for water and wastewater purification(Elsevier, 2018) Gnani Peer Mohamed, G.P.S.; Isloor, A.M.; Yuliwati, E.; A.F., A.F.The carbon-based nanocomposite membranes are developing core technology for water and wastewater purification. These materials are broadly used in the fabrication of ultrafiltration (UF), nanofiltration (NF), reverse osmosis (RO) and evolving forward osmosis (FO) nanocomposite membranes as an additive. In this chapter, performance enhancement of nanocomposite membranes using carbon nanotubes (CNTs) and graphene oxide (GO), especially in the field of desalination, dye removal, oil/water separation and natural organic matter removal, is discussed. © 2019 Elsevier Inc. All rights reserved..Item Synthetic polymer-based membranes for dye and pigment removal(Elsevier, 2020) Gnani Peer Mohamed, G.P.S.; Isloor, A.M.; Lakshmi, B.The use of synthetic polymeric membranes to remove dyes and pigments from industrial wastewater is a growing technology. The toxic and nonbiodegradable nature of dyes and pigments in industrial wastewater influences the importance of the removal of those dyes and pigments. Conventional methods such as coagulation, the photocatalytic process, adsorption, ozonation, plasma treatment, electrochemical treatment, etc., are proposed. However, these methods are very time-consuming, use expensive catalysts, are difficult to scale up, and need secondary treatment. In recent times, a substantial number of attempts have been put forward to advance the performance of polymeric membranes for dye and pigment wastewater treatment. In this chapter, the recent progress on the use of polymeric membranes in processes such as nanofiltration, membrane distillation, and ultrafiltration for effective dye and pigment removal are discussed. © 2020 Elsevier Inc. All rights reserved.Item Advances of membrane technology in wastewater treatment(Elsevier, 2024) Deepthi, P.V.; Viji, K.; Vijesh, A.M.; Isloor, A.M.; Kumar, V.Pure water scarcity is becoming a real threat to the modern world. Rapid growth in the textile, paper, and printing industries has caused the production of large quantities of dye effluents, and they must be treated before passing to the water bodies or lands to minimize pollution and environmental impacts. Polymeric membrane-based filtration has been established as an optimal and greener approach for removing hazardous dyes from polluted water. Superior thermal, chemical, and mechanical properties and convenient modifiability made polysulfone (PSF), polyethersulfone (PES), and polyphenylsulfone (PPSU) ideal for the production of membranes for the treatment of dye effluents from industries. This chapter emphasizes the recent developments in modified PSF, PES, and PPSU membranes and their dye rejection properties. © 2025 Elsevier Inc. All rights reserved.Item Polysulfone/N-phthaloylchitosan novel composite membranes for salt rejection application(2011) Padaki, M.; Isloor, A.M.; Wanichapichart, P.N-phthaloylchitosan (CS) was synthesized by the reaction of chitosan with phthalic anhydride in dimethyl formamide. Different compositions of polysulfone (PSf) and N-phthaloylchitosan were used to prepare novel polysulfone/N-phthaloylchitosan (PSf/CS) composite membranes by phase inversion method. The composition ratios between the former and the latter were 80:20, 85:15, 90:10, and 95:5. Water flux results revealed that, PSf:CS 80:20 membrane is found to have greatest effective pore area while PSf:CS 95:05 membrane has the smallest value. The pore area is found to be larger with the increase in CS composition. In addition, its water swelling property increases with the increase of CS composition. Water flux results are in consistent with dielectric constant value. Use of known molecular weight of polyethylene glycol rejection study, revealed that, PSf:CS 95:05 membrane possessed the smallest pore size among these membranes. In conclusion, change of ratio between PSf and CS, considerably affects membrane pore size and hydrophilicity. For salt filtration, membrane PSf:CS 95:05 showed 93%, 76.11% and 70.12% rejection of MgSO4, Na2SO4, and NaCl, respectively. © 2011 Elsevier B.V.Item Synthesis, characterization and desalination study of novel PSAB and mPSAB blend membranes with Polysulfone (PSf)(2012) Padaki, M.; Isloor, A.M.; A.F., A.F.; Abdullah, M.S.The present paper describes the synthesis of poly sulphonyl amino benzamide (PSAB) and methyalated poly sulphonyl amino benzamide (mPSAB) polymer, using terephthalic acid chloride and substituted 4-amino-1-benzensulphonmide in N-methyl-. 2-pyrrolidone. Polymers were characterized by FT-IR, NMR and GPC. Polysulfone composite membranes were prepared using these novel poymers by DIPS (Diffusion Induced Phase Seperation) method. These composite membranes are useful for water purification with special emphasis on sea water desalination. Newly prepared membranes were studied for salt rejection, water flux, molecular weight cut off by PEG solution, effect of the pH on water swelling and salt rejection and flux decline was also studied. 30 to 70% of the salt rejection was observed in all membranes. Effect of the dilution on salt rejection was studied using different concentration of NaCl solution varying from 1000. ppm to 3500. ppm. All the membranes showed 80% rejection for PEG having 1000. Da molecular weight. Contact angle and water swelling was measured to determine hydrophilicity of the membrane. Water swelling and salt rejection in different pH was also studied. © 2012 Elsevier B.V.Item Preparation and characterization of sulfonated polysulfone and N-phthloyl chitosan blend composite cation-exchange membrane for desalination(2012) Padaki, M.; Isloor, A.M.; Wanichapichart, P.; A.F., A.F.Sulfonated polysulfone (sPSf) was prepared and used as a polymer matrix for cation-exchange membranes (CEM). The sulfonation reaction was carried out at room temperature and the degree of sulfonation was calculated by titration method. Blend composite membranes were prepared using different ratios of sPSf and modified chitosan (CS). Membrane properties were studied in terms of water flux, water swelling ratio, molecular weight cut off (MWCO), ion-exchange capacity (IEC) and contact angle measurement. Charge on the membrane was confirmed by ionic diffusion potential (DP). It was observed that, DP increased with the increase in the concentration of sPSf. The membrane sPSf:CS 60:40 showed 1000Da MWCO, 14.6mV diffusion potential (DP) and 0.083mM/g of IEC. Similarly sPSf:CS 90:10 showed 10,000Da MWCO, 71.7mV diffusion potential (DP) and 0.176mM/g of IEC. Moreover, membrane sPSf:CS 60:40 showed 93%, 89% and 69% for MgSO 4, Na 2SO 4 and NaCl rejection respectively. © 2012 Elsevier B.V.Item Preparation and characterization of polysulfone and modified poly isobutylene-alt-maleic anhydride blend NF membrane(2012) Ganesh, B.M.; Isloor, A.M.; Padaki, M.Recently nanofiltration (NF) is gaining more importance for water treatment. It is replacing the conventional method of water treatment due to advantages of NF membranes over RO system. In this work, we are discussing the preparation of NF membrane for desalination of sea water. We herein report the synthesis of polymer, by the reaction of p-amino benzoic acid (PABA) and poly isobutylene-alt-maleic anhydride (PIAM) and its blend membrane preparation with polysulfone (PSf). The new membranes were characterized by SEM images, surface wettability to investigate the hydrophilic nature of the membrane, water swelling, pure water flux, molecular weight cut-off and salt rejection of the membranes. The membranes showed nano size (<50nm) pores in SEM image, and the contact angle data revealed that membrane surface is moderately hydrophilic. Membrane with 70:30 (PSf:modified PIAM) composition has shown good salt rejection of 96% at 200kPa for 3500ppm of NaCl solution with a pure water flux of 38.36Lm -2h -1. © 2011 Elsevier B.V.Item Synthesis, characterization and desalination study of composite NF membranes of novel Poly[(4-aminophenyl)sulfonyl]butanediamide (PASB) and methyalated Poly[(4-aminophenyl)sulfonyl]butanediamide (mPASB) with Polysulfone (PSf)(2013) Padaki, M.; Isloor, A.M.; Kumar, R.; A.F., A.F.; Matsuura, T.In the present investigation, Poly [(4-aminophenyl)sulfonyl]butanediamide (PASB) and methylated Poly[(4-aminophenyl)sulfonyl] butanediamide (mPASB) polymers were synthesized, using succinyl chloride and substituted 4-amino-1-benzenesulphonamide. Polysulfone composite membranes were prepared by blending these novel polymers by Diffusion Induced Phase Separation (DIPS) method. The performance of the membrane was studied in terms of salt rejection, water flux and molecular weight cutoff. The prepared membranes were hydrophilic in nature, which was confirmed by water uptake studies and contact angle measurement. All the membranes showed 1000. Da molecular weight cutoff. A maximum NaCl rejection of 52% was observed in some of the membranes. The effect of feed NaCl concentration on the NaCl rejection was also studied. The resistance of the membranes in a wide pH range was studied by water uptake measurement. Antifouling properties of the membranes were also performed using Bovine Serum Albumin (BSA) solution. © 2012 Elsevier B.V.Item Studies on copper coated polysulfone/modified poly isobutylene alt-maleic anhydride blend membrane and its antibiofouling property(2013) Isloor, A.M.; Ganesh, B.M.; Isloor, S.; A.F., A.F.; Nagaraj, H.S.; Pattabi, M.As nanofiltration is gaining more and more importance in the field of desalination, one has to address the many obstacles in order to achieve effective/efficient filtration. One such issue is biofouling and microbial attack to the membrane. This paper describes about the study on copper coating onto the membrane surface as biofouling protective layer. This is an attempt to come up with a new approach for desalination and an antimicrobial membrane. The work indicates that, the copper coated membrane can resist the possible microbial attack to some extent while maintaining good salt rejection and appreciable flux. SEM and EDX studies had shown the distribution of copper on the membrane surface. The copper coated membrane had shown the maximum salt rejection of about 96% for 3500ppm NaCl solution and also it had shown the pure water flux of 36Lm-2h-1. © 2012 Elsevier B.V.Item Enhanced hydrophilicity and salt rejection study of graphene oxide-polysulfone mixed matrix membrane(2013) Ganesh, B.M.; Isloor, A.M.; A.F., A.F.Graphene oxide (GO) dispersed polysulfone (PSf) mixed matrix membranes were prepared by wet phase inversion method. The morphology of membranes was studied using scanning electron microscope (SEM) images. The variation in hydrophilicity was studied by measuring surface wettability and water swelling experiments. The performance of membranes in terms of pure water flux and salt rejection was studied. SEM images depict enhanced macrovoids, while the contact angle data reveals that, GO incorporated membrane surface is moderately hydrophilic. Membranes exhibited improved salt rejection after GO doping. Membrane with 2000ppm GO loading has exhibited maximum of 72% Na2SO4 rejection at 4bar applied pressure. The salt rejection seems to depend on pH of the feed solution and it has been witnessed that the salt rejection showed an increasing trend with increase in the pH. © 2012 Elsevier B.V.