Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
11 results
Search Results
Item Synthesis and desalination performance of Ar+-N+ irradiated polysulfone based new NF membrane(2011) Hegde, C.; Isloor, A.M.; Padaki, M.; Wanichapichart, P.; Liangdeng, Y.In the last few years, membrane technology has gained more attention from polymer chemists throughout the globe. Nowadays, surface modification of membrane is very useful in biotechnology and food science. In the present investigation, we have synthesized polysulfone based composite nanofiltration (NF) membranes, and characterized these membranes by FT-IR, SEM and membrane performance studies. Surface plasma treatment was carried out by irradiation with argon and nitrogen beams in suitable conditions. It was observed that nitrogen beam caused surface roughness that was more severe than the Ar beam. After irradiation, water contact angle was slightly increased. For pure water permeability, flux increased linearly with the operating pressure. However, for the salt solution, the flux was decreased marginally and salt rejection increased after irradiation due to surface modification. The modification effect was characterized in terms of contact angle, AFM employed roughness measurement and dielectric property. It revealed that irradiated NF membranes showed higher salt rejection and lower flux as compared to the nonmodified membranes. Accordingly, the roughness of the membrane surface intensively affected the performance of RO membrane. © 2010 Elsevier B.V.Item Polysulfone/N-phthaloylchitosan novel composite membranes for salt rejection application(2011) Padaki, M.; Isloor, A.M.; Wanichapichart, P.N-phthaloylchitosan (CS) was synthesized by the reaction of chitosan with phthalic anhydride in dimethyl formamide. Different compositions of polysulfone (PSf) and N-phthaloylchitosan were used to prepare novel polysulfone/N-phthaloylchitosan (PSf/CS) composite membranes by phase inversion method. The composition ratios between the former and the latter were 80:20, 85:15, 90:10, and 95:5. Water flux results revealed that, PSf:CS 80:20 membrane is found to have greatest effective pore area while PSf:CS 95:05 membrane has the smallest value. The pore area is found to be larger with the increase in CS composition. In addition, its water swelling property increases with the increase of CS composition. Water flux results are in consistent with dielectric constant value. Use of known molecular weight of polyethylene glycol rejection study, revealed that, PSf:CS 95:05 membrane possessed the smallest pore size among these membranes. In conclusion, change of ratio between PSf and CS, considerably affects membrane pore size and hydrophilicity. For salt filtration, membrane PSf:CS 95:05 showed 93%, 76.11% and 70.12% rejection of MgSO4, Na2SO4, and NaCl, respectively. © 2011 Elsevier B.V.Item Synthesis, characterization and desalination study of composite NF membranes of novel Poly[(4-aminophenyl)sulfonyl]butanediamide (PASB) and methyalated Poly[(4-aminophenyl)sulfonyl]butanediamide (mPASB) with Polysulfone (PSf)(2013) Padaki, M.; Isloor, A.M.; Kumar, R.; A.F., A.F.; Matsuura, T.In the present investigation, Poly [(4-aminophenyl)sulfonyl]butanediamide (PASB) and methylated Poly[(4-aminophenyl)sulfonyl] butanediamide (mPASB) polymers were synthesized, using succinyl chloride and substituted 4-amino-1-benzenesulphonamide. Polysulfone composite membranes were prepared by blending these novel polymers by Diffusion Induced Phase Separation (DIPS) method. The performance of the membrane was studied in terms of salt rejection, water flux and molecular weight cutoff. The prepared membranes were hydrophilic in nature, which was confirmed by water uptake studies and contact angle measurement. All the membranes showed 1000. Da molecular weight cutoff. A maximum NaCl rejection of 52% was observed in some of the membranes. The effect of feed NaCl concentration on the NaCl rejection was also studied. The resistance of the membranes in a wide pH range was studied by water uptake measurement. Antifouling properties of the membranes were also performed using Bovine Serum Albumin (BSA) solution. © 2012 Elsevier B.V.Item Preparation and characterization of PPEES/chitosan composite nanofiltration membrane(2013) Shenvi, S.S.; Abdul Rashid, S.A.; A.F., A.F.; Kassim, M.A.; Isloor, A.M.Composite membrane having chitosan (CH) as the active layer supported on Poly(1,4-phenylene ether ether sulfone) (PPEES) membrane was synthesized in the current study. The chitosan layer was crosslinked by glutaraldehyde in two different concentrations. The scanning electron microscopic images and hydraulic permeability coefficient revealed the ultrafiltration (UF) nature of the neat PPEES membrane. This was used as a new support material for the casting of chitosan layer in order to get composite membranes. The composite nature of the PPEES/CH membranes was confirmed by FESEM and DSC analysis. The Infrared spectroscopy results confirmed the crosslinking of the chitosan surface by glutaraldehyde (GA). The changes in the hydrophobic nature of the PPEES membrane surface due to deposition of chitosan active layer followed by crosslinking were studied by their contact angle measurement and water flux study. From our studies, PPEES has proved to be a good support membrane for preparation of composite membranes. Increase in GA concentration increased the salt rejection of the membrane up to 34% for NaCl and 53% for MgSO4 on one hand with a simultaneous decrease in the flux values. The hydraulic permeability coefficient values confirmed that the prepared membranes are in nanofiltration range. © 2012 Elsevier B.V.Item Preparation and characterization study of PPEES/chitosan composite membrane crosslinked with tripolyphosphate(Elsevier, 2014) Shenvi, S.; A.F., A.F.; Isloor, A.M.A novel composite membrane was prepared using chitosan (CH) as the active layer supported on a Poly(1,4-phenylene ether ether sulfone) (PPEES) membrane. The chitosan layer was ionically cross linked with sodium tripolyphosphate (TPP). The composite nature of PPEES/CH membranes was confirmed by Scanning Electron Microscopy (SEM). Infrared (IR) spectroscopy results and SEM-EDX analysis confirmed the crosslinking of chitosan surface with TPP. The membranes exhibited higher crosslinking density in acidic media than in basic media. The changes in the hydrophobic nature of PPEES membrane surface due to deposition of chitosan active layer followed by crosslinking were studied by their contact angle measurement, water flux and water uptake studies. The membranes showed rejection up to 55% and 21% towards MgSO4 and NaCl respectively at pH=5 and a flux recovery ratio of 73%. © 2014 Elsevier B.V.Item Improved desalination by polyamide membranes containing hydrophilic glutamine and glycine(Springer Science and Business Media Deutschland GmbH, 2019) Kolangare, I.M.; Isloor, A.M.; Siddique, I.; Asiri, A.M.; A.F., A.F.Water desalination and recycling of wastewater is a key challenge to meet water shortage issues. Thin film composite polyamide membranes are widely used for desalination; however, their low permeability due to a poor hydrophilicity is a major drawback. Here, we designed novel thin film composite membranes having good hydrophilicity, permeability, and stability without compromising solute rejection. We improved the membrane hydrophilicity by incorporation of hydrophilic additives, such as glycine and l-glutamine, into the polyamide layer. Hence polyamide-based flat sheet membranes were fabricated via interfacial polymerization of m-phenylenediamine and trimesoyl chloride and then were coated over a polysulfone/sulfonated polyphenylsulfone (85:15) support. Polyamide membranes were then characterized and tested for desalination. Results show that the ridge and valley structure observed by scanning electron microscopy confirms the formation of the polyamide layer on membrane surface. The performance reached the highest pure water flux of 36.23 Lm?2 h?1 and flux recovery ratio of 89.18% for membranes with 2 wt% of l-glutamine. Incorporation of 2 wt% l-glutamine induced a high permeate flux and a maximum rejection of 87.87% for MgSO4, 83.50% for Na2SO4 and 60.77% for NaCl solutions. Overall, the polyamide nanofiltration membrane with hydrophilic groups displayed superior antifouling property and can be used as a potential candidate for desalination. © 2018, Springer Nature Switzerland AG.Item Fabrication of TiO2@ZIF-67 metal organic framework composite incorporated PVDF membranes for the removal of hazardous reactive black 5 and Congo red dyes from contaminated water(Elsevier B.V., 2024) Prabhakar, N.; Isloor, A.M.; Padaki, M.; Fauzi Ismail, A.Novel application of TiO2@ZIF-67 composite incorporated poly (vinylidene fluoride) (PVDF) mixed matrix flat-sheet membranes for treating the water contaminated with hazardous reactive black 5 and congored dyes was the crux of this work. The composite was characterized by FTIR, BET, XRD, zeta potential and particle size, and TGA. The as-synthesized composite was embedded in the PVDF polymeric matrix and flat-sheet-membranes were fabricated adopting the NIPS method followed by the different characterizations like scanning electron microscopy, EDS, elemental mapping, contact angle, atomic force microscopy, surface energy, and XPS. Results of the performance studies showed an enhanced pure water permeability from 150.99 Lm-2h?1 for neat membrane to 261.39 Lm-2h?1 for TZM-2. The reactive black 5 dye was rejected in 97.4 %, 92.2 %, and 84.84 % in acidic, basic and neutral conditions respectively by TZM-2 membrane. Whereas, the PVDF membranes without the composite showed rejections of 83.19 %, 82.5 %, and 72.1 % respectively in acidic, basic, and neutral conditions. The Congo Red dye was rejected in 89.4 %, 95.68 %, and 92.4 % in acidic, neutral and basic conditions respectively by TZM-2 membranes. Whereas, the PVDF membranes without the composite showed rejections of 82.8 %, 91.9 %, and 85.4 % respectively in acidic, neutral and basic conditions. © 2024Item Effective removal of hazardous atrazine and chlorpyrifos by waste PET bottles-derived linker having novel MIL-53(Al)/PMMA-nanofiber incorporated poly(vinylidene) fluoride membranes(Elsevier Ltd, 2025) Prabhakar, N.; Isloor, A.M.; Farnood, R.Synthesis of novel MIL-53(Al)/PMMA nanofiber and its incorporation into PVDF thin-film composite flat-sheet membranes for the rejection of hazardous herbicides and pesticides from water is the crux of this work. Initially, poly (methyl methacrylate) polymer dope solution with MIL-53(Al) dispersed in the matrix was subjected to electrospinning to get a novel nanofiber. The linker terephthalic acid, here was derived from waste PET bottles. Both the MOF and nanofibers were characterized using BET, FTIR, zeta potential, and XRD. The optimized nanofibers were used as additives in the TFC in different weight percentages using synthesized porous PVDF as support. TFC Membranes were analyzed by pure water flux, chlorpyrifos, and atrazine rejection. MPM-2 with 0.05 wt% nanofiber gave a pure water flux of 18.6824 Lm?2h?1. The rejection of chlorpyrifos (a hazardous pesticide) was 86.8 % for MPM-2 membranes and atrazine (a herbicide) gave rejection of 60.48 %. Further, membranes gave excellent antifouling property with FRR of 95.45 %. © 2025 Elsevier LtdItem Development of polymeric ionic poly(VBC-co-VI) nanoparticle incorporated thin film nanocomposite membranes for dye and salt rejection(Royal Society of Chemistry, 2025) Mendonca, N.R.; Isloor, A.M.; Farnood, R.Water is an important life-sustaining liquid. However, due to the current anthropogenic activities, this resource is diminishing. This work explores a method for the potential reuse of textile wastewater containing salts by utilization of thin film composite (TFC) membranes fabricated by means of interfacial polymerization on a macroporous membrane substrate composed of 15% polysulfone (PSf). A relatively lesser known variety of nanoparticles termed ionic polymeric nanoparticles were integrated into the dense polyamide (PA) layer. The ionic poly(VBC-co-VI) nanoparticles were synthesized in the laboratory via quaternary precipitation polymerization (QPP) of the monomers 1-vinyl imidazole (VI) and 4-vinybenzyl chloride (VBC) by the utilization of 2,2?-azobis(2-methylpropionitrile) (AIBN) as the free radical initiator in the solvent acetonitrile (ACN) in a single step. The synthesized nanoparticles existing in the PA layer improved the water permeability as well as the rejection capacity of the membranes. The fabricated membranes showed a dye rejection of 98% for Reactive Black 5 and >95% for Sunset Yellow FCF having a concentration of 100 ppm. The salt rejection for NaCl, MgCl, Na2SO4 and MgSO4 at 1000 ppm concentration was found to be 36%, >50%, 85% and 85%, respectively. © 2025 The Royal Society of Chemistry.Item Fabrication and incorporation of MIL-53(Fe)-zwitterionic brushes into PVDF thin film composite membranes for enhancing heavy metal/dye rejection from aqueous body(Elsevier B.V., 2025) Prabhakar, N.; Isloor, A.M.; Farnood, R.; Fauzi Ismail, A.The bioaccumulation of heavy metal ions is a serious concern for researchers. The dyes and heavy metal ions also aquatic life impacting the biodiversity adversely. Synthesis of novel MIL-53(Fe)-PSBMA particles, and its incorporation into PVDF-based thin-film composite membranes is the crux of this work. Firstly, H2N-MIL-53(Fe) was synthesized by metal displacement reaction which was then modified into MIL-53(Fe)-PSBMA brushes. The brushes were synthesized by atom transfer radical polymerization method. The amine groups of the NH2-MIL-53(Fe) help connecting the MOF to the polymeric moiety. The as-synthesized material and the fabricated TFCs were characterized by BET, FTIR, XRD, XPS, TGA, AFM, FE-SEM, zeta potential, and DLS particle sizer. The presence of sulphur groups on the XPS spectrum of modified MOF ensured the successful polymer grafting on it. Zwitterionic moieties have both positive and negative charges within a single molecule which gave a resultant zeta potential of ?13.1 mV for the brushes. A pure water flux of 26.32 Lm?2 h?1 and 97.33 %, 95.19 %, 82.06 %, and 78.47 % rejections for Pb2+, Hg2+, As3+, Cd2+ ions and 96.23 % and 94.04 % rejection for 100 ppm reactive black-5 and sunset yellow dyes respectively were obtained for the optimized membrane having 0.035 wt% loading of zwitterionic MOF. This result was attributed to the enhanced membrane hydrophilicity which was also correlated with contact angle and water uptake studies. © 2024 Elsevier B.V.