Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Properties of Mn3O4 thin film electrodes prepared using spray pyrolysis for supercapacitor application(Elsevier Ltd, 2023) Pramitha, A.; Hegde, S.S.; Badekai Ramachandra, B.R.; George, S.D.; Sudhakar, S.N.; Raviprakash, R.Film electrodes are made by depositing a thin layer of an electroactive material onto a conductive substrate. The performance of thin film electrodes in energy storage devices is significantly governed by their preparative conditions, particularly the molar concentration of the initial precursor. In the current study, the preparation of Mn3O4 thin film electrodes utilizing the chemical spray pyrolysis technique is discussed. The effect of molar concentration on the structural, morphological, and electrochemical properties of the thin film electrodes was thoroughly investigated using techniques including X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and galvanostatic charge/discharge (GCD) studies. Additionally, X-ray photoelectron spectroscopy (XPS) was employed to gain more insight into the oxidation states of the sample with the best electrochemical performance. Findings suggested that the molar concentration considerably affects the crystallite size, surface area, surface roughness, and wettability, which would directly impact the functionality of the electrode. It was concluded that the electrode deposited using the molar concentration of 0.06 M showed significantly improved performance according to the electrochemical measurements. The areal capacitance of up to 105.3 mF/cm2 in the aqueous electrolyte was recorded from CV measurements at a scan rate of 5 mVs−1. These electrodes could be an option for low-cost, environmentally friendly electrochemical capacitors if prepared under optimal deposition conditions. © 2023 Elsevier B.V.Item Biomass waste-derived porous graphitic carbon for high-performance supercapacitors(Elsevier Ltd, 2024) Hegde, S.S.; Badekai Ramachandra, B.R.Porous carbons possess considerable appeal and are in high demand as materials that can be produced from biomass waste. This study presents the transformation of Tectona grandis (Teak) sawdust into porous carbon materials, referred to as Tectona grandis sawdust-derived porous carbon (TPC), through a cost-effective FeCl3-assisted carbonization process, followed by a KOH activation. TPC samples were synthesized by carbonization at different temperatures (650–850 °C) and characterized comprehensively. Structural analysis via X-Ray diffraction (XRD), Raman, and Fourier Transform Infrared Spectroscopy (FTIR) revealed a progressive enhancement in graphitic structure and reduction of functional groups with increasing activation temperature. Field emission scanning electron microscopy (FESEM) displayed the development of intricate hollow tube-like porous networks in TPC-850, with the highest specific surface area (1767.66 m2/g) and pore volume (1.43 cm3/g). Electrochemical investigations showcased the superior performance of TPC-850 as a supercapacitor electrode due to its high graphitic nature, large surface area, and well-structured porosity. The galvanostatic charge-discharge (GCD) measurements exhibited a high specific capacitance of 572 F/g at 0.5 A/g in a 6 M KOH electrolyte. The high-frequency semicircle and low-frequency steeper region in electrochemical impedance spectroscopy (EIS) further indicated reduced resistance and enhanced ion diffusion in TPC-850. Significantly, TPC-850 demonstrated remarkable electrochemical cyclic stability, retaining 95.83 % of its initial capacity even after undergoing 4500 cycles at a scan rate of 500 mV/s. The findings underscore the viability of TPC-850 as a high-performance supercapacitor electrode material, providing insights into harnessing renewable resources for advanced energy solutions. This work highlights the potential of utilizing waste biomass for energy storage applications and demonstrates the feasibility of converting it into efficient porous carbon materials with substantial graphitization and porosity. © 2023 Elsevier LtdItem Sustainable energy storage: Mangifera indica leaf waste-derived activated carbon for long-life, high-performance supercapacitors(Royal Society of Chemistry, 2024) Hegde, S.S.; Badekai Ramachandra, B.R.Biomass waste-derived activated carbon has a wide range of applications, including air and water purification, gas separation, energy storage, and catalysis. This material has become increasingly popular in recent years as a result of the growing demand for sustainable and eco-friendly materials. In this study, Mangifera indica leaf waste-derived activated carbon has been investigated as an electrode material for high-performance supercapacitors. The dried Mangifera indica leaves were first carbonized using FeCl3 and then activated using KOH to increase their surface area and pore structure at different temperatures. The activated carbon prepared at 725 °C has shown a high specific capacitance of 521.65 F g−1 at a current density of 0.5 A g−1 and also achieved an energy density of 17.04 W h kg−1 at a power density of 242.50 W kg−1 in the 6 M KOH electrolyte. Significantly, it has demonstrated remarkable electrochemical cycling stability, retaining 96.60% of its initial capacity even after undergoing 10 001 cycles at a scan rate of 500 mV s−1. The superior electrochemical performance of the activated carbon can be attributed to its high surface area of 1232.63 m2 g−1, well-distributed pore size, and excellent degree of graphitization, which all facilitate the rapid diffusion of ions and enhance the accessibility of the electrolyte to the electrode surface. Hence, this study provides a promising route for utilizing waste biomass as a low-cost, sustainable electrode material for energy storage devices. © 2024 The Royal Society of Chemistry.Item Impact of electrolyte concentration on electrochemical performance of Cocos nucifera Waste-Derived High-Surface carbon for green energy storage(Elsevier Ltd, 2024) Hegde, S.S.; Badekai Ramachandra, B.R.The increasing popularity of utilizing biomass's natural structure represents a promising avenue for sustainable innovation, as it taps into the inherent characteristics of organic materials to address various environmental and industrial challenges. Researchers and industries continue to explore the full potential of biomass in creating more sustainable and efficient solutions. The transformation of biomass into carbon materials is an indirect means of utilizing CO2 as a carbon source, thus contributing to the sustainable development of energy storage technologies and also in pollution reduction. In the quest for sustainable energy solutions, this research unveils a cost-effective approach to supercapacitor development by harnessing the untapped potential of Cocos nucifera trunk sawdust-derived high-surface carbon (CHSC). Through a meticulous process involving ZnCl2 treatment and KOH activation at varying temperatures, CHSC-700 emerges as a standout electrode material with exceptional structural characteristics, boasting enhanced graphitization and a specific surface area of 1153.72 m2/g. Further, the study delved into the nuanced relationship between electrolyte concentration and supercapacitor performance, pinpointing 6 M KOH as the optimal condition. In 6 M KOH, the electrode exhibits a maximum specific capacitance of 559.27F/g at the current density of 0.5 A/g with outstanding cyclic stability, retaining 80.37 % capacitance after 20,000 cycles and an impressive energy density of 18.92 Wh/kg and power density of 246.75 W/kg. This systematic exploration provides valuable data for understanding the biomass-derived carbon electrode's behaviour under various electrolyte concentrations, offering crucial information for optimizing its performance in practical applications, such as energy storage devices. © 2024 Elsevier Ltd