Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
9 results
Search Results
Item Electrolytic preparation of cyclic multilayer Zn-Ni alloy coating using switching cathode current densities(2010) Venkatakrishna, K.; Hegde, A.C.Cyclic multilayer alloy (CMA) coating of Zn-Ni was developed on mild steel using single bath technique, by proper manipulation of cathode current densities. The thickness and composition of the individual layers were altered precisely and conveniently by cyclic modulation of cathode current densities. Multilayer coatings, having sharp change in compositions were developed using square current pulses. Gelatin and sulphanilic acid (SA) acid were used as additives. Laminar deposits with different configurations were produced, and their corrosion behaviors were studied, in 5% NaCl solution by electrochemical methods. It was observed that the corrosion resistance of CMA coating increased progressively with number of layers (up to certain optimal numbers) and then decreased. Cyclic voltammetry study demonstrated the role of gelatin and SA in multilayer coating. The coating configuration has been optimized for the peak performance against corrosion. The substantial decrease of corrosion rate, in the case of multilayer coatings was attributed to the changed intrinsic electric properties, evidenced by Electrochemical Impedance Spectroscopy (EIS) study. The surface morphology and its roughness were examined by Atomic Force Microscopy (AFM). The surface and cross-sectional view of coatings were examined, using Scanning Electron Microscopy (SEM). X-ray photoelectron spectrum (XPS) study was carried out for surface analysis. The relative performance of pure Zn, monolithic and CMA coatings were compared and discussed. © 2010 Springer Science+Business Media B.V.Item Composition modulated multilayer Zn-Fe alloy coatings on mild steel for better corrosion resistance(2011) Venkatakrishna, K.; Hegde, A.C.Composition modulated alloy (CMA) of Zn-Fe coatings were developed on mild steel galvanostatically from chloride bath containing sulphanilic acid (SA) and ascorbic acid (AA) through single bath technique (SBT). The properties of CMA coatings were found to depend on the thickness of individual layers and switching cathode current densities (SCCDs). The CMA (Zn-Fe) coating, having 120 layers, deposited at 20 and 50mAcm-2, were found to show the least corrosion rate (1.545 × 10-2mmy-1) compared to monolithic alloy (32.5 × 10-2mmy-1) of the same thickness. The improved corrosion resistance of multilayered coatings was due to the fact that the defects and failures occurring in a single layer in the deposition process is covered by the successively deposited coating layers, and hence the corrosive agent path is extended or blocked. Further, the high corrosion resistance of CMA Zn-Fe coatings was attributed to the "dielectric barrier" of the coatings, evidenced by dielectric spectroscopy and Mott-Schottky's plot. The corrosion rate was found to increase at high degree of layering, and is attributed to less relaxation time for redistribution of metal ions in diffusion layer, during plating. In other words, at higher layer thickness, the CMA coating tends to become a monolithic. CMA coatings were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). © Taylor & Francis Group, LLC.Item Development of anti-corrosive multi-layered coatings of zinc-nickel alloy(2011) Subbaiah, Y.; Kaje, V.; Hegde, A.C.Purpose: The purpose of this paper is to develop and optimize anti-corrosive multi-layered coatings of zinc-nickel alloy on carbon steel. Design/methodology/approach: A variety of composition-modulated multi-layer alloy (CMMA) coatings of zinc-nickel were developed on a carbon steel substrate by cyclic changes in cathode current during electrodeposition, coupled with variation of the thicknesses of the individual layers. The corrosion behavior of the coatings was studied in 5 percent NaCl solution by electrochemical methods. Cyclic cathode current densities (CCCDs) and the number of alloy layers were optimized for highest performance of the coatings against corrosion. The factors responsible for improved corrosion resistance were analyzed in terms of change in the intrinsic electrical properties of the capacitance value at the electrical double layer that was associated with micro/nanometric layering. The formation of the semi-conductive surface film, which was responsible for the improved corrosion resistance, was supported by a Mott-Schottky plot and the cyclic polarization study. The formation of multi-layered deposit and the mechanism of corrosion degradation of the coating were analyzed using scanning electron microscopy. Findings: CMMA coatings with an optimal configuration of (Zn-Ni)2.0/4.0/300 showed ~35 times better corrosion resistance compared to a monolithic (Zn-Ni)3.0 alloy coating of the same thickness. The peak performance was attributed to the change in intrinsic electrical properties of the coating and this conclusion was supported by dielectric spectroscopy. Originality/value: The paper describes the optimization of CCCD and the number of deposited layers by development of electrolytic deposition of anti-corrosive multi-layered zinc-nickel coatings from a single plating technique. © Emerald Group Publishing Limited.Item Optimization of deposition conditions for development of high corrosion resistant Zn-Fe multilayer coatings(2011) Yogesha, S.; Hegde, A.C.Composition modulated multilayer alloy (CMMA) coating of Zn-Fe was developed galvanostatically on mild steel through single bath technique (SBT), using thiamine hydrochloride as additive. Electrodeposits with different coating matrices were developed, using square current pulses. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) methods were used to assess the corrosion performance of the coatings. The cyclic cathode current densities (CCCDs) and number of layers were optimized, for highest corrosion resistance. Experimental results showed that CMMA Zn-Fe coating, developed at 2.0-4.0 A/dm2, having 300 layers is ?30 times higher corrosion resistant than corresponding monolithic alloy of same thickness. The corrosion resistance increased with number of layers up to a certain number of layers; and then decreased. The better corrosion resistance was attributed to the dielectric barrier at the interface, evidenced by dielectric spectroscopy. The formation of multilayer and corrosion mechanism was analyzed using scanning electron microscopy (SEM). © 2011 Elsevier B.V. All rights reserved.Item Corrosion protection of electrodeposited multilayer nanocomposite Zn-Ni-SiO2 coatings(2013) Ullal, Y.; Hegde, A.C.Multilayer nanocomposite coatings of Zn-Ni-SiO2 were deposited galvanostatically on mild steel (MS) from Zn-Ni bath, having Zn+2 and Ni+2 ions and uniformly dispersed nano-SiO2 particles. The corrosion characteristics and properties of multilayered nanocomposite (MNC) coatings were evaluated by electrochemical polarization and impedance methods. Such deposition conditions as, bath composition, cyclic cathode current densities (CCCD's) and number of layers were optimized for peak performance of coatings against corrosion. A significant improvement in the corrosion performance of MNC coatings was observed when a coating was changed from a monolayer to multilayer type. Corrosion rate (CR) of MNC coating decreased progressively with number of layers up to an optimal level, and then started increasing. The increase of CR at a higher degree of layering is attributed to diffusion of layers due to a very short deposition time, failing to give the enhanced corrosion protection. The formation of layers, inclusion of silica particle in MNC coating matrix were confirmed by SEM and XRD study. At optimal current densities, i.e. at 3.0-5.0 A/cm2, the Zn-Ni-SiO2 coating having 300 layers, represented as (Zn-Ni-SiO2)30/5.0/300 is found to be about 107 times more corrosion resistant than a monolayer Zn-Ni-SiO2 coating, developed from the same bath for the same time. The reasons responsible for the extended corrosion protection of MNC Zn-Ni-SiO2 coatings, compared to corresponding monolayer Zn-Ni and (Zn-Ni-SiO2) coatings were analyzed, and results were discussed. © 2013 Allerton Press, Inc.Item Production of layered coatings of Fe-Ni alloy for enhanced corrosion protection(2013) Pavithra, G.P.; Hegde, A.C.Layered Fe-Ni alloy coatings have been galvanostatically developed on copper using dual and triple square current pulse from acid sulfate bath. The cyclic cathode current density (CCCD) and number of layers have been optimized for enhanced performance of the coatings against corrosion. Corrosion behavior of the coatings is evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy methods in 1 M HCl solution. The polarization study confirms that coatings developed using triple square pulses are more corrosion resistant than those deposited by dual square pulses. The improved corrosion behavior of layered coatings is due to the changed intrinsic electric properties evidenced by the electrochemical impedance spectroscopy. Under optimal conditions, the coatings developed using dual and triple square current pulse have been found to be by about 23 and 57 times, respectively, more corrosion resistant than the monolithic alloys. Surface morphology and layered coatings have been examined by scanning electron microscopy. Saturation of corrosion resistance at a high degree of layering was found, which is attributed to a shorter relaxation time for redistribution of metal ions during plating. © 2013 Allerton Press, Inc.Item Synergistic effect of gelatin and glycerol on electrodeposition of Zn-Ni alloy(2013) Rao, V.R.; Hegde, A.C.The use of organic compounds which improves corrosion resistance has attracted growing interest in electroplating technology. In this direction, this article presents the experimental results of electrodeposition of Zn-Ni alloy on mild steel (MS) from acid chloride bath using gelatin and glycerol as additives. The bath composition and operating parameters have been optimized by the conventional Hull cell method. The effect of gelatin and glycerol, individually and in combination on the deposition process, was identified by a cyclic voltammetry (CV) study at different scan rates. Bright deposition of Zn-Ni alloy was found at optimal current density (c.d.) due to the preferential deposition of gelatin and glycerol by controlling the Ni content of the alloy. The CV study demonstrated that alloy deposition is diffusion controlled when additives were used individually and is adsorption controlled when used in combination. Corrosion behaviors at different current densities (c.d.s) were evaluated by potentiodynamic polarization and electrochemical impedance (EIS) methods. The surface morphology and phase structure of the coatings were analyzed by field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) studies. The experimental results revealed that both gelatin and glycerol have synergistic effects in improving the electrocrystallization process and, hence, the corrosion stability of the coatings. At an optimal c.d. (3.0 A dm-2), the Zn-Ni alloy coating showed peak performance against corrosion with the least corrosion rate. Better corrosion protection at optimal c.d., which was attributed to specific Zn(101), ?-(411,330), and Zn(103) reflections, is evidenced by the XRD study. © 2013 The Minerals, Metals & Materials Society and ASM International.Item Nanofabricated multilayer coatings of Zn-Ni alloy for better corrosion protection(2013) Rao, V.R.; Hegde, A.C.As an effort to increase the corrosion resistance of conventional monolayer Zn-Ni alloy coating, the multilayer Zn-Ni alloy coating have been done electrolytically on mild steel (MS), using gelatin and glycerol as additives. Multilayered, or more correctly composition modulated multilayer alloy (CMMA) coatings have been developed using square current pulse. Successive layers of alloys, in nanometric scale having alternately changing composition were fabricated by making the cathode current to cycle between two values, called cyclic cathode current densities (CCCD's). The coatings having different configuration, in terms of composition and thicknesses of individual layers were developed and their corrosion performances were evaluated by electrochemical methods. The corrosion rate (CR)'s were found to decrease drastically with progressive increase in number of layers (up to 300 layers), and then increased. The coating configurations have been optimized for best protection against corrosion. The CMMA Zn-Ni coating having 300 layers was found to be about 37 times more corrosion resistant than corresponding monolayer alloy, developed from same bath for same time. High protection efficacy of the coatings were attributed to alternate layers of alloys having different surface structure and composition, supported by Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD) study, respectively. Optimization procedure has been explained, and results are discussed. © 2013 Pleiades Publishing, Ltd.Item Role of cadmium on corrosion resistance of Zn-Ni alloy coatings(Allerton Press Inc. journals@allertonpress.com, 2014) Rao, V.R.; Hegde, A.C.Cadmium (Cd) catalyzed Zn-Ni alloy plating has been accomplished galvanostatically on mild steel (MS) using gelatin and glycerol as additives. The effect of addition of Cd into Zn-Ni bath has been examined in terms of nickel (Ni) content and corrosion resistance of Zn-Ni-Cd ternary alloy coatings. The process and product of electrolysis under different concentrations of additives and Cd have been investigated by cyclic voltammetry (CV). The effects of current density (c.d.) on Ni content of the alloy have been studied by spectrophotometric method, supported by EDX analysis. The deposition has been carried out under different concentrations of Cd ranging from 0.004 to 0.1 M. The corrosion rates (CR) of Zn-Ni alloy coatings have been found to decrease drastically with addition of Cd. It has been also revealed that the CR of binary Zn-Ni alloy coatings decreased with the increase of Cd concentration only up to a certain optimal concentration, i.e., up to 0.02 M, and then remained unchanged. An effort to change the anomalous type of codeposition into normal one by changing the molar ratios of the metal ions, i.e. [Cd2+]/[Ni2+] as 0.01, 0.05 and 0.25 has remained futile. CV study demonstrated an important role of Cd in mutual depositions of Zn2+ and Ni2+ ions by its preferential adsorption, thus leading to the increased Ni content of the alloy. The bath composition and operating parameters have been optimized for deposition of bright and uniform Zn-Ni-Cd alloy coatings. Changes in the surface morphology and phase structure of Zn-Ni alloy coatings due to addition of Cd has been confirmed by Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD) study respectively. Experimental investigations so as to identify the role of Cd in codeposition Zn-Ni alloy coatings have been carried out and the results are discussed. © 2014 Allerton Press, Inc.