Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.Hegde, A.C.Subject: search.filters.subject.Electrodeposition

Search Results

Now showing 1 - 10 of 22
  • No Thumbnail Available
    Item
    Electrodeposition of Sn-Ni alloy coatings and their characterization
    (Trans Tech Publications Ltd ttp@transtec.ch, 2015) Shetty, S.; Hegde, A.C.
    A new alkaline bath has been proposed for deposition of bright Sn-Ni alloy coatings on mild steel (MS). Depositions were carried out at different current densities (c.d.) and their corrosion behaviors were studied in 5% NaCl solution by electrochemical AC and DC methods. Sn-Ni coating, deposited at low c.d. i.e. at 1.0 A/dm2 was found to be the most corrosion resistant compared to those at other higher c.d., even up to 4.0 A/dm2. This least corrosion rate (CR) is attributed to high wt. % Sn in the deposit. Increase of CR at high c.d. range is due to decrease of wt. % Sn, explained by the observed anomalous type of codeposition, followed by the bath. Regardless of the deposition c.d., the bath developed bright coatings, inherent of Sn-Ni alloy. Experimental results are discussed taking in account of the phase structure, composition and surface morphology of the coatings, evidenced by X-ray diffraction (XRD), Energy Dispersive X-ray (EDX) and Scanning Electron Microscopy (SEM) analysis. © (2015) Trans Tech Publications, Switzerland.
  • No Thumbnail Available
    Item
    Electrodeposition of high performance multilayer coatings of Zn-Co using triangular current pulses
    (2010) Yogesha, S.; Hegde, A.C.
    Compositionally modulated alloy (CMA) coatings of Zn-Co were electrodeposited on to mild steel from an acid chloride bath containing thiamine hydrochloride, as an additive. Electroplating was carried out galvanostatically from a single bath containing Zn2+ and Co2+ ions. Gradual change in composition in each layer was effected by triangular current pulses, cycling between two cathode current densities. Compositionally modulated alloy coatings were developed under different conditions of cyclic cathode current density and number of layers, and their corrosion resistances were evaluated by potentiodynamic polarisation and electrochemical impedance spectroscopy. The formation of multilayer and corrosion mechanism was analysed using scanning electron microscopy. The corrosion resistances of CMA and monolithic alloy coatings were compared with that of the base metal. Compositionally modulated alloy coating at optimal configuration, represented as (Zn-Co) 2•0/4•0/300, was found to exhibit ?80 times better corrosion resistance compared with monolithic (Zn-Co)3•0 alloy, deposited for the same length of time from the same bath. Improved corrosion resistance was attributed to the formation of n-type semiconductor film at the interface, supported by Mott-Schottky plots. Decrease in corrosion resistance at high degree of layering was found, and is due to lower relaxation time for redistribution of solutes in the diffusion double layer, during plating. © 2010 Maney Publishing.
  • No Thumbnail Available
    Item
    Electroplating and characterization of Zn-Ni, Zn-Co and Zn-Ni-Co alloys
    (2010) Eliaz, N.; Venkatakrishna, K.; Hegde, A.C.
    Zn-Ni, Zn-Co and Zn-Ni-Co coatings were electrodeposited on mild steel from an acidic chloride bath containing p-aminobenzenesulphonic acid (SA) and gelatin. These additives changed the phase content in the coatings, most likely as a result of their adsorption at the surface of the cathode. The effect of gelatin was more pronounced than that of SA. The Faradaic efficiency was higher than 90%. As the current density was increased or the bath temperature was decreased, the concentration of the nobler metal in the coating increased. Both concentrations of Ni and Co in the ternary alloy increased as the applied current density was increased. Nickel and cobalt were found to have a synergistic catalytic effect. The thickness of all coatings increased as the applied current density was increased. The hardness increased with current density to a peak value, and then decreased. The rate of Zn deposition was heavily influenced by mass-transport limitation at high applied current densities, while the rates of Ni and Co deposition were not. The anomalous codeposition was explained by the great difference between the exchange current densities of Zn and the iron-group metal. Potentiodynamic polarization scans and electrochemical impedance spectroscopy showed that the corrosion resistance of the ternary Zn-Ni-Co alloy coatings was approximately 10 times higher than that of Zn-Ni and 7 times higher than that of Zn-Co. The improved corrosion resistance of the ternary alloy was attributed to its surface chemistry, phase content, texture, and surface morphology. The ternary Zn-Ni-Co coating may thus replace the conventional Zn-Ni and Zn-Co coatings in a variety of applications. © 2010 Elsevier B.V.
  • No Thumbnail Available
    Item
    Electrodeposition of Zn-Ni, Zn-Fe and Zn-Ni-Fe alloys
    (2010) Hegde, A.C.; Venkatakrishna, K.; Eliaz, N.
    Zn-Fe, Zn-Ni and Zn-Ni-Fe coatings were electrodeposited galvanostatically on mild steel from acidic baths (pH 3.5) consisted of ZnCl2, NiCl2, FeCl2, gelatin, sulfanilic (p-aminobenzenesulfonic) acid and ascorbic acid. Cyclic voltammetry showed that the effect of gelatin was more pronounced than that of sulfanilic acid, and that the deposition of the ternary alloy behaved differently from the deposition of the binary alloys. In all three systems, the Faradaic efficiency was higher than 88%, the rate of Zn deposition was heavily influenced by mass-transport limitation at high applied current densities, and the deposition was of anomalous type. For each applied current density, the concentrations of Ni and Fe in the ternary alloy were higher than the corresponding concentrations in the binary alloys. The hardness of Zn-Ni coatings was the highest, while that of Zn-Fe coatings was the lowest. The Zn-Ni-Fe coatings were the smoothest, had distinguished surface morphology, and contained ZnO in the bulk, not just on the surface. The lowest corrosion rate in each alloy system (214, 325 and 26?m year-1 for Zn-Ni, Zn-Fe and Zn-Ni-Fe, respectively) was characteristic of coatings deposited at 30, 30 and 40mAcm-2, respectively. The higher corrosion resistance of the ternary alloy was also reflected by a higher corrosion potential, a higher impedance and a higher slope of the Mott-Schottky line. The enhanced corrosion behavior of the ternary alloy was thus attributed to its chemical composition, phase content, roughness and the synergistic effect of Ni and Fe on the n-type semiconductor surface film. © 2010 Elsevier B.V.
  • No Thumbnail Available
    Item
    Composition modulated multilayer Zn-Fe alloy coatings on mild steel for better corrosion resistance
    (2011) Venkatakrishna, K.; Hegde, A.C.
    Composition modulated alloy (CMA) of Zn-Fe coatings were developed on mild steel galvanostatically from chloride bath containing sulphanilic acid (SA) and ascorbic acid (AA) through single bath technique (SBT). The properties of CMA coatings were found to depend on the thickness of individual layers and switching cathode current densities (SCCDs). The CMA (Zn-Fe) coating, having 120 layers, deposited at 20 and 50mAcm-2, were found to show the least corrosion rate (1.545 × 10-2mmy-1) compared to monolithic alloy (32.5 × 10-2mmy-1) of the same thickness. The improved corrosion resistance of multilayered coatings was due to the fact that the defects and failures occurring in a single layer in the deposition process is covered by the successively deposited coating layers, and hence the corrosive agent path is extended or blocked. Further, the high corrosion resistance of CMA Zn-Fe coatings was attributed to the "dielectric barrier" of the coatings, evidenced by dielectric spectroscopy and Mott-Schottky's plot. The corrosion rate was found to increase at high degree of layering, and is attributed to less relaxation time for redistribution of metal ions in diffusion layer, during plating. In other words, at higher layer thickness, the CMA coating tends to become a monolithic. CMA coatings were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). © Taylor & Francis Group, LLC.
  • No Thumbnail Available
    Item
    Corrosion stability of electrodeposited cyclic multilayer Zn-Ni alloy coatings
    (2011) Bhat, R.S.; Udupa, K.R.; Hegde, A.C.
    This paper reports on a study of electrodeposition and characterisation of cyclic multilayer coatings of Zn-Ni alloy from a sulphate bath. Cyclic multilayer alloy coatings were deposited on mild steel through the single bath technique by appropriate manipulation of cathode current densities. The thickness and composition of the individual layers of the CMA deposits were altered precisely and conveniently by cyclic modulation of the cathode current during electrodeposition. Multilayer deposits with sharp change in composition were developed using square current pulses, using thiamine hydrochloride and citric acid as additives. Laminar deposits with different configurations were produced and their corrosion behaviours were studied by AC and DC methods in 5%NaCl solution. It was observed that the corrosion resistance of the CMA coating increased progressively with the number of layers (up to certain optimal numbers) and then decreased. The decrease in corrosion resistance at high degree of layering was attributed to interlayer diffusion due to less relaxation time for redistribution of metal ions at cathode during deposition. The coating configurations have been optimised for peak performance of the coatings against corrosion. It was found that CMA coating developed at cyclic cathode current densities of 3.0/5.0 A dm-2 with 300 layers showed the lowest corrosion rate (0.112×10-2 mm/year) which is ?54 times better than that of monolithic Zn-Ni alloy, deposited from the same bath. The protection efficacy of CMA coatings is attributed to the difference in phase structure of the alloys in successive layers, deposited at different current densities, evidenced by X-ray diffraction analysis. The formation of multilayers and corrosion mechanism were examined by scanning electron microscopy. © 2011 Institute of Metal Finishing.
  • No Thumbnail Available
    Item
    Magnetically induced electrodeposition of Zn-Ni alloy coatings and their corrosion behaviors
    (Elsevier B.V., 2013) Rao, V.R.; Bangera, K.V.; Hegde, A.C.
    The less magnetic features of Zn-Ni alloy compared to Fe-Ni and Fe-Co alloys made it interesting to develop them under the influence of applied magnetic field. In this regard, the effects of a magnetic field (B) applied in a direction parallel and perpendicular to the nominal current, during electrodeposition process of Zn-Ni alloy have been investigated by means of X-ray diffraction and EDX analysis. The modification of crystal orientation by superimposition of a varying magnetic field is studied for alloys of constant nickel content (8 a %.), deposited at optimal current density (j) of 3.0 A dm-2. The effect of magnetic field on crystallographic orientation and hence the corrosion behaviors of the coatings were studied. The preferential orientations (101) and (002) of the zinc phase and (330) ?-Ni 5Zn21 phase are always favored to exist with parallel and perpendicular magnetic field. The preferential (321) ?-Ni 5Zn21 orientation is found to be the characteristic of perpendicular magnetic field. Further, Zn (100) orientation is found to be non-responsive to the effect of parallel magnetic field. The coatings developed using perpendicular magnetic field is more corrosion resistant compare to that for parallel magnetic field. This is attributed to the additional (321) ?-Ni5Zn21 orientations. The changes in the phase structure of the coatings deposited at different magnetic field are attributed to the effect caused by the magnetic convection induced in the electrolytic solution, called MHD effect (magneto-hydrodynamic effect). The chemical composition of the alloy was found to be same in both natural and magnetically induced deposition due to constant Ni content in the bath. The variation in the surface morphology of the coatings was studied by scanning electron microscopy (SEM). The Zn-Ni alloy coating deposited at 0.8 T perpendicular B showed the highest corrosion resistance (with corrosion rate=0.26 × 10-2 mm y-1) compared to the one with no B (corrosion rate = 14.46 × 10-2 mm y-1). The improved corrosion resistance of the coatings was discussed in the light of magnetic field effect on crystallographic orientation. © 2013 Elsevier B.V. All rights reserved.
  • No Thumbnail Available
    Item
    Optimization of bright Zn-Co-Ni alloy coatings and its characterization
    (2013) Bhat, R.S.; Hegde, A.C.
    Acidic sulphate bath having ZnSO4.7H2O, CoSO4.7H2O, NiSO4.7H2O and thiamine hydrochloride (THC) and citric acid (CA) in combination, was optimized for deposition of bright Zn-Co-Ni alloy coating on mild steel. Bath constituents and operating parameters were optimized by Hull cell method, for highest performance of the coating against corrosion. The effect of current density (c.d.), on deposit characters, such as corrosion resistance and hardness, thickness were studied and discussed. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) methods were used to assess the corrosion behaviors. The composition of deposits were determined by spectrophotometeric method and confirmed by EDX analysis. Surface morphology of the deposits was examined using scanning electron microscopy (SEM). The Zn-Co-Ni alloy, with intense peaks corresponding to Zn (100) and Zn (101) and Zn (110) phases, showed highest corrosion resistance, evidenced by X-ray diffraction (XRD) study. A new and cheap sulphate bath, for bright Zn-Co-Ni alloy coating on mild steel has been proposed, and results are discussed. © 2013 by CEE.
  • No Thumbnail Available
    Item
    Synergistic effect of gelatin and glycerol on electrodeposition of Zn-Ni alloy
    (2013) Rao, V.R.; Hegde, A.C.
    The use of organic compounds which improves corrosion resistance has attracted growing interest in electroplating technology. In this direction, this article presents the experimental results of electrodeposition of Zn-Ni alloy on mild steel (MS) from acid chloride bath using gelatin and glycerol as additives. The bath composition and operating parameters have been optimized by the conventional Hull cell method. The effect of gelatin and glycerol, individually and in combination on the deposition process, was identified by a cyclic voltammetry (CV) study at different scan rates. Bright deposition of Zn-Ni alloy was found at optimal current density (c.d.) due to the preferential deposition of gelatin and glycerol by controlling the Ni content of the alloy. The CV study demonstrated that alloy deposition is diffusion controlled when additives were used individually and is adsorption controlled when used in combination. Corrosion behaviors at different current densities (c.d.s) were evaluated by potentiodynamic polarization and electrochemical impedance (EIS) methods. The surface morphology and phase structure of the coatings were analyzed by field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) studies. The experimental results revealed that both gelatin and glycerol have synergistic effects in improving the electrocrystallization process and, hence, the corrosion stability of the coatings. At an optimal c.d. (3.0 A dm-2), the Zn-Ni alloy coating showed peak performance against corrosion with the least corrosion rate. Better corrosion protection at optimal c.d., which was attributed to specific Zn(101), ?-(411,330), and Zn(103) reflections, is evidenced by the XRD study. © 2013 The Minerals, Metals & Materials Society and ASM International.
  • No Thumbnail Available
    Item
    Electrodeposition and electro-catalytic study of nanocrystalline Ni-Fe alloy
    (Elsevier Ltd, 2014) Ullal, Y.; Hegde, A.C.
    This paper presents the electrodeposition protocol for development of a stable, inexpensive and efficient electrode material for water splitting reaction. Nanocrystalline Ni-Fe alloy coatings were deposited on copper electrode from acidic bath, at different cathode current densities (c.d). Coatings were tested for their electro-catalytic behaviours, namely for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in 6 M KOH by cyclic voltammetry and chrono-potentiometry techniques. Experimental results demonstrated that these coatings can be used as potential material for water electrolysis. The corrosion stability of these coatings has also been tested in their working conditions (6 M KOH) by DC polarization method. The deposition conditions of Ni-Fe alloy were optimized for peak performance for both electro-catalytic reactions and corrosion stability. Ni-Fe alloy coatings deposited towards low and high c.d limits were found to be the better materials for OER and HER, respectively from same electrolytic solution. Further, Ni-Fe coating deposited at 6.0 Ad m-2 was found to be the most corrosion resistant. The structure-property relationship of electrodeposited coatings has been discussed by exploring PXRD, EDX and FESEM study. © 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.