Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item Electroplating and characterization of Zn-Ni, Zn-Co and Zn-Ni-Co alloys(2010) Eliaz, N.; Venkatakrishna, K.; Hegde, A.C.Zn-Ni, Zn-Co and Zn-Ni-Co coatings were electrodeposited on mild steel from an acidic chloride bath containing p-aminobenzenesulphonic acid (SA) and gelatin. These additives changed the phase content in the coatings, most likely as a result of their adsorption at the surface of the cathode. The effect of gelatin was more pronounced than that of SA. The Faradaic efficiency was higher than 90%. As the current density was increased or the bath temperature was decreased, the concentration of the nobler metal in the coating increased. Both concentrations of Ni and Co in the ternary alloy increased as the applied current density was increased. Nickel and cobalt were found to have a synergistic catalytic effect. The thickness of all coatings increased as the applied current density was increased. The hardness increased with current density to a peak value, and then decreased. The rate of Zn deposition was heavily influenced by mass-transport limitation at high applied current densities, while the rates of Ni and Co deposition were not. The anomalous codeposition was explained by the great difference between the exchange current densities of Zn and the iron-group metal. Potentiodynamic polarization scans and electrochemical impedance spectroscopy showed that the corrosion resistance of the ternary Zn-Ni-Co alloy coatings was approximately 10 times higher than that of Zn-Ni and 7 times higher than that of Zn-Co. The improved corrosion resistance of the ternary alloy was attributed to its surface chemistry, phase content, texture, and surface morphology. The ternary Zn-Ni-Co coating may thus replace the conventional Zn-Ni and Zn-Co coatings in a variety of applications. © 2010 Elsevier B.V.Item Magnetically induced electrodeposition of Zn-Ni alloy coatings and their corrosion behaviors(Elsevier B.V., 2013) Rao, V.R.; Bangera, K.V.; Hegde, A.C.The less magnetic features of Zn-Ni alloy compared to Fe-Ni and Fe-Co alloys made it interesting to develop them under the influence of applied magnetic field. In this regard, the effects of a magnetic field (B) applied in a direction parallel and perpendicular to the nominal current, during electrodeposition process of Zn-Ni alloy have been investigated by means of X-ray diffraction and EDX analysis. The modification of crystal orientation by superimposition of a varying magnetic field is studied for alloys of constant nickel content (8 a %.), deposited at optimal current density (j) of 3.0 A dm-2. The effect of magnetic field on crystallographic orientation and hence the corrosion behaviors of the coatings were studied. The preferential orientations (101) and (002) of the zinc phase and (330) ?-Ni 5Zn21 phase are always favored to exist with parallel and perpendicular magnetic field. The preferential (321) ?-Ni 5Zn21 orientation is found to be the characteristic of perpendicular magnetic field. Further, Zn (100) orientation is found to be non-responsive to the effect of parallel magnetic field. The coatings developed using perpendicular magnetic field is more corrosion resistant compare to that for parallel magnetic field. This is attributed to the additional (321) ?-Ni5Zn21 orientations. The changes in the phase structure of the coatings deposited at different magnetic field are attributed to the effect caused by the magnetic convection induced in the electrolytic solution, called MHD effect (magneto-hydrodynamic effect). The chemical composition of the alloy was found to be same in both natural and magnetically induced deposition due to constant Ni content in the bath. The variation in the surface morphology of the coatings was studied by scanning electron microscopy (SEM). The Zn-Ni alloy coating deposited at 0.8 T perpendicular B showed the highest corrosion resistance (with corrosion rate=0.26 × 10-2 mm y-1) compared to the one with no B (corrosion rate = 14.46 × 10-2 mm y-1). The improved corrosion resistance of the coatings was discussed in the light of magnetic field effect on crystallographic orientation. © 2013 Elsevier B.V. All rights reserved.Item Compositionally Modulated Multilayered Zn-Co Deposits for Better Corrosion Resistance(Springer, 2020) Bhat, R.S.; Venkatakrishna, K.; Nayak, J.; Hegde, A.C.Zn-Co compositionally modulated multilayer alloy (CMMA) deposits have been developed onto mild steel using single bath technique. Multilayer alloy coatings have been galvanostatically produced using square current pulses. The switched cathode current density and number of layers have been designed for improved corrosion resistance. Experimental data revealed that multilayer coating with 120 layers at 10/30 mA/cm2 demonstrated ~ 125 times higher resistance to corrosion than monolayer alloy coating of the same thickness. The improved corrosion resistance of multilayer coatings is due to small changes in the wt.% cobalt, leading to change in the phase structure of deposit in alternate layers. The defects and failures occurring in a single layer in the deposition process are covered by the alternatively deposited coating layers. Therefore, the direction of the corrosive agent is extended or blocked. Further, the better corrosion resistances afforded by Zn-Co CMMA coatings were explained through changes in electronic properties at the interface, supported by Mott-Schottky’s plot. However, the decrease of corrosion resistance at a high degree of layering is attributed to the less relaxation time for redistribution of solutes in the diffusion layer, during plating. Potentiodynamic polarization and electrochemical impedance data showed its good protection ability. The enhanced corrosion resistance of multilayered deposits is due to small change in cobalt content, leading to alter the phase structure of the alternate-layers of the deposits. The structural morphology and the topographical structure of the coating were analyzed by scanning electron microscopy and atomic force microscopy. Evaluation of the chemical composition of the alloy coatings was carried out by x-ray photoelectron spectroscopy. © 2020, ASM International.Item Anomalous codeposition of NiCo alloy coatings and their corrosion behaviour(Elsevier Ltd, 2022) Raveendran, M.N.; Hegde, A.C.Here, we report the electrodeposition NiCo alloy coatings from a new bath using the glycine, as additive. A bright and uniform coatings NiCo alloy have been developed at different current densities and their corrosion performances have been evaluated. The surface morphology, composition and phase structure of alloy coatings have been analyzed using Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Spectroscopy (EDS) and X-ray diffraction (XRD) techniques, respectively. The compositional information of NiCo alloy coatings revealed that the proposed bath follows anomalous type of codeposition over range of current density studied (1.0–4.0 A dm−2), by demonstrating more Wt. % of Co in the deposits, than in the bath. A constant increase in the Wt. % of Ni with current density was found, supported by XRD analyses; and it may be attributed to the depletion of more readily depositable Co+2 ions at cathode film by following the principle of codeposition of NiCo alloy. The corrosion study revealed that NiCo alloy deposited at 4.0 A dm−2, represented as (NiCo) 4.0 A dm-2 coating is the most corrosion resistant compared to all other coatings. The highest corrosion stability of (NiCo) 4.0 A dm-2 alloy attributed to its highest Ni content (38.6 wt%) and increased surface smoothness, supported by EDS and SEM study. © 2022Item Electrodeposition of Zn–Co Coating and its Electrochemical Performance(Pleiades journals, 2022) Bhat, R.S.; Manjunatha, K.B.; Venkatakrishna, K.; Hegde, A.C.Abstract: We report the acid chloride bath based electroplating of Zn–Co alloy on low carbon steel (LCS). As additives, the sulphanilic acid (SA) and gelatin were used for electroplating. The bath exhibited an anomalous co-deposition with a higher deposition of Zn over nobler Co. The role of bath composition, current density, partial current density, pH, and temperature on thickness, hardness, and corrosion resistance of deposit was studied. The corrosion behavior in 3.5 wt % sodium chloride solution and electrochemical behavior in acid chloride solutions of Zn–Co alloy coatings were studied using the potentiodynamic polarization method and cyclic voltammetry technique respectively. Mott–Schottky plot with positive slope confirms the development of n-type semiconductor layer at the interface of substrate and coating, which results in superior corrosion resistance of coatings. The colorimetric method has been used to estimate the composition of the deposit and further verified by energy dispersive X-ray spectroscopy (EDX) technique. The surface features and the topographical structure of the alloy film were obtained by scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques. The results indicate that the Zn–Co alloy films exhibited superior corrosion resistance with the lowest corrosion rate (138 µm y–1). Hence this alloy coating will find suitable applications in automobile and aerospace industries. © 2022, Pleiades Publishing, Ltd.Item Effect of Magnetic Field on Corrosion Performance of Ni–Co Alloy Coatings(Springer Science and Business Media Deutschland GmbH, 2023) Shetty, A.R.; Hegde, A.C.The corrosion protection efficacy of Ni–Co alloy coatings was tried to improve by magnetoelectrodeposition (MED) approach. The magnetic field of varying strength (B) was applied in perpendicular and parallel to the direction of diffusion of metal ions, simultaneously to the process of deposition. The corrosion behaviour of the deposited coatings was studied through electrochemical DC method and results revealed that Magneto-electrodeposited (MED) Ni–Co alloys coatings were found to be more corrosion resistant than their conventionally electrodeposited (ED) counterparts. Moreover, the effect of magnetic field is more pronounced in perpendicular field direction and was explained by Lorentz force. Under optimal condition, MED Ni–Co alloy coating obtained at a magnetic field intensity of B = 0.3 T (Perpendicular) was found to be less prone to corrosion than its ED alloy (B = 0 T) counterpart. The increased limiting current density (iL) of Co2+ ions in turn increases the corrosion resistant properties of MED Ni–Co alloy coatings. The effect of magnetic field on improved corrosion resistance of the deposited coatings have been investigated in terms of their changed surface morphology, composition, phase structure and surface roughness using Scanning electron microscopy (SEM), Energy dispersion spectroscopy (EDS), X-Ray diffraction (XRD) technique and Atomic Force Microscopy (AFM) respectively. © 2022, The Author(s).Item Electrodeposition and Electrocatalytic Study of Ni–Co Alloy Coatings(Pleiades Publishing, 2024) Yathish Rai, T.; Hegde, A.C.Abstract: The present work focusses on the fabrication of new Ni–Co electrolyte for the development of Ni–Co electrocatalysts for water splitting application. All the Ni–Co alloy coatings were deposited from an acid sulphate bath and their electrocatalytic activity was tested in 1 M KOH. The Ni–Co alloys developed at range of current density from 3.0 to 6.0 A dm–2 were found to be good electrode materials for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER), as demonstrated by cyclic voltammetry (CV) and chronopotentiometry (CP) methods. The Ni–Co alloy deposits which are catalytically active for HER are found to be inactive for OER and vice versa. The change in surface appearance, composition, and the phase structure of all developed coatings were analysed using instrumental techniques like scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD), respectively. © Pleiades Publishing, Ltd. 2024.