Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
10 results
Search Results
Item Electrolytic preparation of cyclic multilayer Zn-Ni alloy coating using switching cathode current densities(2010) Venkatakrishna, K.; Hegde, A.C.Cyclic multilayer alloy (CMA) coating of Zn-Ni was developed on mild steel using single bath technique, by proper manipulation of cathode current densities. The thickness and composition of the individual layers were altered precisely and conveniently by cyclic modulation of cathode current densities. Multilayer coatings, having sharp change in compositions were developed using square current pulses. Gelatin and sulphanilic acid (SA) acid were used as additives. Laminar deposits with different configurations were produced, and their corrosion behaviors were studied, in 5% NaCl solution by electrochemical methods. It was observed that the corrosion resistance of CMA coating increased progressively with number of layers (up to certain optimal numbers) and then decreased. Cyclic voltammetry study demonstrated the role of gelatin and SA in multilayer coating. The coating configuration has been optimized for the peak performance against corrosion. The substantial decrease of corrosion rate, in the case of multilayer coatings was attributed to the changed intrinsic electric properties, evidenced by Electrochemical Impedance Spectroscopy (EIS) study. The surface morphology and its roughness were examined by Atomic Force Microscopy (AFM). The surface and cross-sectional view of coatings were examined, using Scanning Electron Microscopy (SEM). X-ray photoelectron spectrum (XPS) study was carried out for surface analysis. The relative performance of pure Zn, monolithic and CMA coatings were compared and discussed. © 2010 Springer Science+Business Media B.V.Item Electrodeposition of high performance multilayer coatings of Zn-Co using triangular current pulses(2010) Yogesha, S.; Hegde, A.C.Compositionally modulated alloy (CMA) coatings of Zn-Co were electrodeposited on to mild steel from an acid chloride bath containing thiamine hydrochloride, as an additive. Electroplating was carried out galvanostatically from a single bath containing Zn2+ and Co2+ ions. Gradual change in composition in each layer was effected by triangular current pulses, cycling between two cathode current densities. Compositionally modulated alloy coatings were developed under different conditions of cyclic cathode current density and number of layers, and their corrosion resistances were evaluated by potentiodynamic polarisation and electrochemical impedance spectroscopy. The formation of multilayer and corrosion mechanism was analysed using scanning electron microscopy. The corrosion resistances of CMA and monolithic alloy coatings were compared with that of the base metal. Compositionally modulated alloy coating at optimal configuration, represented as (Zn-Co) 2•0/4•0/300, was found to exhibit ?80 times better corrosion resistance compared with monolithic (Zn-Co)3•0 alloy, deposited for the same length of time from the same bath. Improved corrosion resistance was attributed to the formation of n-type semiconductor film at the interface, supported by Mott-Schottky plots. Decrease in corrosion resistance at high degree of layering was found, and is due to lower relaxation time for redistribution of solutes in the diffusion double layer, during plating. © 2010 Maney Publishing.Item Composition modulated multilayer Zn-Fe alloy coatings on mild steel for better corrosion resistance(2011) Venkatakrishna, K.; Hegde, A.C.Composition modulated alloy (CMA) of Zn-Fe coatings were developed on mild steel galvanostatically from chloride bath containing sulphanilic acid (SA) and ascorbic acid (AA) through single bath technique (SBT). The properties of CMA coatings were found to depend on the thickness of individual layers and switching cathode current densities (SCCDs). The CMA (Zn-Fe) coating, having 120 layers, deposited at 20 and 50mAcm-2, were found to show the least corrosion rate (1.545 × 10-2mmy-1) compared to monolithic alloy (32.5 × 10-2mmy-1) of the same thickness. The improved corrosion resistance of multilayered coatings was due to the fact that the defects and failures occurring in a single layer in the deposition process is covered by the successively deposited coating layers, and hence the corrosive agent path is extended or blocked. Further, the high corrosion resistance of CMA Zn-Fe coatings was attributed to the "dielectric barrier" of the coatings, evidenced by dielectric spectroscopy and Mott-Schottky's plot. The corrosion rate was found to increase at high degree of layering, and is attributed to less relaxation time for redistribution of metal ions in diffusion layer, during plating. In other words, at higher layer thickness, the CMA coating tends to become a monolithic. CMA coatings were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). © Taylor & Francis Group, LLC.Item Development of anti-corrosive multi-layered coatings of zinc-nickel alloy(2011) Subbaiah, Y.; Kaje, V.; Hegde, A.C.Purpose: The purpose of this paper is to develop and optimize anti-corrosive multi-layered coatings of zinc-nickel alloy on carbon steel. Design/methodology/approach: A variety of composition-modulated multi-layer alloy (CMMA) coatings of zinc-nickel were developed on a carbon steel substrate by cyclic changes in cathode current during electrodeposition, coupled with variation of the thicknesses of the individual layers. The corrosion behavior of the coatings was studied in 5 percent NaCl solution by electrochemical methods. Cyclic cathode current densities (CCCDs) and the number of alloy layers were optimized for highest performance of the coatings against corrosion. The factors responsible for improved corrosion resistance were analyzed in terms of change in the intrinsic electrical properties of the capacitance value at the electrical double layer that was associated with micro/nanometric layering. The formation of the semi-conductive surface film, which was responsible for the improved corrosion resistance, was supported by a Mott-Schottky plot and the cyclic polarization study. The formation of multi-layered deposit and the mechanism of corrosion degradation of the coating were analyzed using scanning electron microscopy. Findings: CMMA coatings with an optimal configuration of (Zn-Ni)2.0/4.0/300 showed ~35 times better corrosion resistance compared to a monolithic (Zn-Ni)3.0 alloy coating of the same thickness. The peak performance was attributed to the change in intrinsic electrical properties of the coating and this conclusion was supported by dielectric spectroscopy. Originality/value: The paper describes the optimization of CCCD and the number of deposited layers by development of electrolytic deposition of anti-corrosive multi-layered zinc-nickel coatings from a single plating technique. © Emerald Group Publishing Limited.Item Development of nano-structured cyclic multilayer Zn-Ni alloy coatings using triangular current pulses(2011) Bhat, R.S.; Hegde, A.C.Cyclic multilayer alloy (CMA) deposits of Zn-Ni were developed on mild steel from sulphate bath having thiamine hydrochloride (THC) and citric acid (CA) as additives. CMA coatings were developed galvanostatically using triangular current pulses, under different conditions of cyclic cathode current density (CCCD's) and number of layers. The corrosion behaviors of the coatings were evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy methods, and were compared with that of monolayer Zn-Ni alloy of same thickness. At optimal configuration, CMA coating represented as, (Zn-Ni)2.0/5.0/300 was found to exhibit ?40 times better corrosion resistance compared to monolayer alloy, (Zn-Ni)3.0. Cyclic voltammetry study demonstrated that THC and CA have improved the appearance of the deposit by complexation with metal ions. The corrosion protection efficacy of CMA coatings was attributed to the difference in phase structure of the alloy in successive layers, evidenced by XRD analysis. The formation of multilayer and corrosion mechanism was analyzed by Scanning Electron Microscopy (SEM) study. © 2011 Allerton Press, Inc.Item Corrosion stability of electrodeposited cyclic multilayer Zn-Ni alloy coatings(2011) Bhat, R.S.; Udupa, K.R.; Hegde, A.C.This paper reports on a study of electrodeposition and characterisation of cyclic multilayer coatings of Zn-Ni alloy from a sulphate bath. Cyclic multilayer alloy coatings were deposited on mild steel through the single bath technique by appropriate manipulation of cathode current densities. The thickness and composition of the individual layers of the CMA deposits were altered precisely and conveniently by cyclic modulation of the cathode current during electrodeposition. Multilayer deposits with sharp change in composition were developed using square current pulses, using thiamine hydrochloride and citric acid as additives. Laminar deposits with different configurations were produced and their corrosion behaviours were studied by AC and DC methods in 5%NaCl solution. It was observed that the corrosion resistance of the CMA coating increased progressively with the number of layers (up to certain optimal numbers) and then decreased. The decrease in corrosion resistance at high degree of layering was attributed to interlayer diffusion due to less relaxation time for redistribution of metal ions at cathode during deposition. The coating configurations have been optimised for peak performance of the coatings against corrosion. It was found that CMA coating developed at cyclic cathode current densities of 3.0/5.0 A dm-2 with 300 layers showed the lowest corrosion rate (0.112×10-2 mm/year) which is ?54 times better than that of monolithic Zn-Ni alloy, deposited from the same bath. The protection efficacy of CMA coatings is attributed to the difference in phase structure of the alloys in successive layers, deposited at different current densities, evidenced by X-ray diffraction analysis. The formation of multilayers and corrosion mechanism were examined by scanning electron microscopy. © 2011 Institute of Metal Finishing.Item Production of layered coatings of Fe-Ni alloy for enhanced corrosion protection(2013) Pavithra, G.P.; Hegde, A.C.Layered Fe-Ni alloy coatings have been galvanostatically developed on copper using dual and triple square current pulse from acid sulfate bath. The cyclic cathode current density (CCCD) and number of layers have been optimized for enhanced performance of the coatings against corrosion. Corrosion behavior of the coatings is evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy methods in 1 M HCl solution. The polarization study confirms that coatings developed using triple square pulses are more corrosion resistant than those deposited by dual square pulses. The improved corrosion behavior of layered coatings is due to the changed intrinsic electric properties evidenced by the electrochemical impedance spectroscopy. Under optimal conditions, the coatings developed using dual and triple square current pulse have been found to be by about 23 and 57 times, respectively, more corrosion resistant than the monolithic alloys. Surface morphology and layered coatings have been examined by scanning electron microscopy. Saturation of corrosion resistance at a high degree of layering was found, which is attributed to a shorter relaxation time for redistribution of metal ions during plating. © 2013 Allerton Press, Inc.Item Nanofabricated multilayer coatings of Zn-Ni alloy for better corrosion protection(2013) Rao, V.R.; Hegde, A.C.As an effort to increase the corrosion resistance of conventional monolayer Zn-Ni alloy coating, the multilayer Zn-Ni alloy coating have been done electrolytically on mild steel (MS), using gelatin and glycerol as additives. Multilayered, or more correctly composition modulated multilayer alloy (CMMA) coatings have been developed using square current pulse. Successive layers of alloys, in nanometric scale having alternately changing composition were fabricated by making the cathode current to cycle between two values, called cyclic cathode current densities (CCCD's). The coatings having different configuration, in terms of composition and thicknesses of individual layers were developed and their corrosion performances were evaluated by electrochemical methods. The corrosion rate (CR)'s were found to decrease drastically with progressive increase in number of layers (up to 300 layers), and then increased. The coating configurations have been optimized for best protection against corrosion. The CMMA Zn-Ni coating having 300 layers was found to be about 37 times more corrosion resistant than corresponding monolayer alloy, developed from same bath for same time. High protection efficacy of the coatings were attributed to alternate layers of alloys having different surface structure and composition, supported by Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD) study, respectively. Optimization procedure has been explained, and results are discussed. © 2013 Pleiades Publishing, Ltd.Item Electrofabrication of multilayer Fe-Ni alloy coatings for better corrosion protection(Springer Verlag service@springer.de, 2014) Ullal, Y.; Hegde, A.C.Electrofabrication of multilayer Fe-Ni alloy coatings were accomplished successfully on mild steel and their corrosion behaviors were studied. Multilayer comprised of alternatively formed 'nano-size' layers of Fe-Ni alloy of different composition have been produced from a single bath having Fe 2+and Ni2+ ions using modulated (i.e. periodic pulse control) current density (cd). The deposition conditions were optimized for both composition and thickness of individual layers for best performance of the coatings against corrosion. The deposits were analyzed using scanning electron microscopy (SEM), powder X-ray diffraction (PXRD), Hardness Tester, electrochemical AC and DC methods respectively. The multi layered deposits showed better corrosion resistances compared to the monolayer Fe-Ni (CR = 3.77 mm year-1) coating deposited using DC from the same bath; the maximum corrosion resistance being shown by the coating having 300 layers, deposited at cyclic cathodic current densities of 2.0 and 4.0 A dm-2 (CR = 0.03 mm year-1). Drastic improvement in the corrosion performance of multilayer coatings were explained in the light of changed kinetics of mass transfer at cathode and increased surface area due to modulation and layering. © 2014 Springer-Verlag Berlin Heidelberg.Item Electrodeposition and electro-catalytic study of nanocrystalline Ni-Fe alloy(Elsevier Ltd, 2014) Ullal, Y.; Hegde, A.C.This paper presents the electrodeposition protocol for development of a stable, inexpensive and efficient electrode material for water splitting reaction. Nanocrystalline Ni-Fe alloy coatings were deposited on copper electrode from acidic bath, at different cathode current densities (c.d). Coatings were tested for their electro-catalytic behaviours, namely for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in 6 M KOH by cyclic voltammetry and chrono-potentiometry techniques. Experimental results demonstrated that these coatings can be used as potential material for water electrolysis. The corrosion stability of these coatings has also been tested in their working conditions (6 M KOH) by DC polarization method. The deposition conditions of Ni-Fe alloy were optimized for peak performance for both electro-catalytic reactions and corrosion stability. Ni-Fe alloy coatings deposited towards low and high c.d limits were found to be the better materials for OER and HER, respectively from same electrolytic solution. Further, Ni-Fe coating deposited at 6.0 Ad m-2 was found to be the most corrosion resistant. The structure-property relationship of electrodeposited coatings has been discussed by exploring PXRD, EDX and FESEM study. © 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.