Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
9 results
Search Results
Item Corrosion behavior of composition modulated multilayer Zn-Co electrodeposits produced using a single-bath technique(2009) Thangaraj, V.; Eliaz, N.; Hegde, A.Composition modulated alloy (CMA) electrodeposits of Zn-Co were produced from acid chloride baths by the single-bath technique. Their corrosion behavior was evaluated as a function of the switched cathode current densities and the number of layers. The process was optimized with respect to the highest corrosion resistance. Enhanced corrosion resistance was obtained when the outer layer was slightly richer with cobalt. At the optimum switched current densities 40/55 mA cm-2, a coating with 600 layers showed ~6 times higher corrosion resistance than monolithic Zn-Co electrodeposit having the same thickness. The CMA coating exhibited red rust only after 1,130 h in a salt-spray test. The increased corrosion resistance of the multilayer alloys was related to their inherent barrier properties, as revealed by Electrochemical Impedance Spectroscopy. The corrosion resistance was explained in terms of n-type semiconductor films at the interface as supported by Mott-Schottky plots. © 2008 Springer Science+Business Media B.V.Item Electrodeposition and characterization Zn-Co alloy(2009) Hegde, A.; Thangaraj, V.The present work details optimization of a stable acid chloride bath for electroplating of bright Zn-Co alloy on mild steel using gelatin and glycine as additives. It was found that the addition of gelatin along with glycine changed the deposition pattern markedly. A suitable bath has been formulated using conventional Hull cell experiments. The bath under plating conditions were found to exhibit anomalous codeposition with preferential deposition of less noble (zinc) over more noble (cobalt) as characterized by Zn-Fe group metal alloys. Investigation revealed that the current density (c.d.), temperature, and pH of the bath have strong effect on the composition of the deposit. Influence of bath constituents and operating parameters on appearance and composition of deposits were studied as measure of their performance against corrosion. A variety of deposits were obtained and their corrosion resistances were measured by Tafel method with/without chrome passivation. Experimental results demonstrated the fact that the corrosion resistances of Zn-Co alloys increased with percent of Co in the deposit except at very high c.d. This is due to the fact at very high c.d. the deposit becomes very porous and thick as evidenced by SEM image. The formation of Zn-Co alloy is confirmed by EDAX analysis. A stable chloride bath for Zn-Co alloy deposition has been proposed and discussed. The formation of passive film on chromatization is indicated by almost same E corr value of all Zn-Co electroplates irrespective of the current densities at which they have been deposited. © 2009 Pleiades Publishing, Ltd.Item Magnetic property and corrosion resistance of electrodeposited nanocrystalline iron-nickel alloys(Elsevier B.V., 2012) Pavithra, G.P.; Hegde, A.In the present investigation we have galvanostatically synthesized nanocrystalline Fe-Ni alloys on copper substrate. The effect of current density (c.d.) on composition, surface morphology and phase structure were studied for explaining the magnetic and electrochemical properties of the nanocrystalline alloy. The bath found to exhibit the preferential deposition of less noble Fe than Ni, and at no conditions of c.d., the deposition has changed from anomalous to normal type. Surface morphology and structural characteristics of the deposits were examined using scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. As composition of the alloy varied, consequent to the current density a change of body centered cubic structure (bcc) to face centered cubic structure (fcc) was observed for nanocrystalline materials. Finally, the conditions responsible for peak magnetic property and corrosion resistance were optimized. Factors responsible for improved functional properties were explained in terms of surface morphology and crystalline grain size of the coatings. © 2012 Elsevier B.V.Item Production of layer by layer Zn-Fe compositional multilayer alloy coatings using triangular current pulses for better corrosion protection(Maney Publishing, 2015) Bhat, R.S.; Hegde, A.Multiple-layer coatings of Zn-Fe alloy having alternatively the same compositions have been developed galvanostatically on mild steel (MS) from a single plating bath using triangular current pulses. Thiamine hydrochloride (THC) and citric acid (CA) were used as additives. Multiple-layer coatings were developed under different conditions of cyclic cathode current density (CCCD) and number of layers. Cyclic voltammetry demonstrated that the addition of THC and CA improves the deposit character by increasing the Ni content (through suppressing the deposition of Zn) via preferential adsorption on the cathode surface. The corrosion behaviours of the coatings were evaluated by electrochemical AC and DC methods. The optimum multiple-layer coating, represented as (Zn-Fe)3.0/5.0/300, was found to exhibit about four to five times better corrosion resistance when compared with monolayer (Zn-Fe)3.0 alloy, developed from the same bath for the same duration. Distinct phase structures responsible for interface formation between successive layers (which changes alternatively) were confirmed by X-ray diffraction analysis. Better corrosion resistance afforded by multiple-layer coating was attributed to the increased specific surface area of the coating because of layering. A synergistic effect of both structural difference between layers and individual layer thickness is responsible for enhanced corrosion resistance of the multiple-layer coatings. The formation of multiple layers and corrosion mechanism were analysed by scanning electron microscopy. © 2015 Institute of Materials Finishing.Item Electrodeposition of laminar coatings of Ni-W alloy and their corrosion behaviour(Elsevier, 2015) Elias, L.; Hegde, A.The attractiveness of electroplating for the synthesis of advanced materials is linked to large selection of plating conditions coupled with different mass transfer processes towards the cathode, and this allows the tailoring of different properties of many electrodeposited coatings. This theme has been exploited effectively in the development of a new class of coatings; called composition modulated multilayered (CMM), or in short laminar coatings. The work embodied in this paper is to demonstrate how the corrosion resistance of monolayer Ni-W alloys can be increased to many fold of its magnitude by multilayer deposition. Ni-W coatings have been deposited on mild steel (MS) in a laminar multilayer pattern from a citrate bath using single bath technique (SBT). Electrodeposits having alternate layers of alloys, having different compositions were developed by modulating the direct current (DC). CMM coating configurations have been optimized from a newly developed bath, in terms of current pulse height and thickness of each layer to maximize its corrosion protection ability, in relation to its monolayer coating, developed from same bath for same time. The process and product of the Ni-W coatings have been characterized using different instrumental methods, such as cyclic voltammetry (CV), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) study. The better corrosion resistance behaviour of CMM Ni-W coatings has been analysed in the light of increased surface areas of the coatings due to layering, and results are discussed. © 2015 Elsevier B.V.Item Ultrasound induced multilayer Ni-Co alloy coatings for better corrosion protection(Elsevier B.V., 2017) Shetty, A.R.; Hegde, A.Ultrasound induced multilayer Ni-Co alloy coatings have been developed galvanostatically by periodic modulation of ultrasound effect, parallel to the process of conventional electroplating. Multilayer Ni-Co alloy having alternative layers of different composition were developed by turning the sonicator probe, ON and OFF periodically, while keeping the current density (c.d.) constant. The deposition conditions, in terms of pulsing power density (p.d.) and degree of layering have been optimized for the highest performance of coating against corrosion, evaluated by electrochemical testing methods. Corrosion data revealed that under optimal conditions, multilayer Ni-Co alloy coating having 150 layers, represented as (Ni-Co)2/2/150 is about 11 times more corrosion resistant than its homogeneous coating, represented as (Ni-Co)4.0 A dm ? 2, deposited from the same bath for same duration of time. Improved corrosion resistance of multilayer Ni-Co alloy coatings was attributed to an increase in the number of interfaces, separating the layers of alloys of different composition, affected due to periodic pulsing of the sonicator. The dependence of corrosion behaviors at different combination of c.d. and p.d., on surface morphology, composition and phase structures were analyzed, using scanning electron microscopy (SEM), energy dispersion spectroscopy (EDS) and X-ray diffraction (XRD) technique, respectively. Experimental results are compared, and discussed. © 2017 Elsevier B.V.Item Development of Composition Modulated Multilayer (NiTi) Alloy Coatings for Improved Corrosion Protection of Mild Steel(Pleiades Publishing, 2024) Harshini Sa, G.; Hegde, A.Abstract: A new class of materials known as composition modulated multilayer (CMM) alloy coatings has created an ever-increasing interest in materials research due to their improved functional properties. In this direction, an effort has been made to improve the poorer corrosion resistance performance of conventional monolayer nickel–titanium (NiTi) alloy coatings (due to inherent induced type of codeposition), their multilayer alloy coatings have been developed. CMM (NiTi) alloy coatings have been fabricated electrolytically on mild steel (MS) from a citrate bath, using the glycerol as additive. Multilayer alloy coatings of varying matrices have been developed by periodic modulation of direct current (DC), in terms of pulse height and pulse duration. Coating configurations in both composition and thickness of alternate layers were optimized for best performance of the alloy coatings against corrosion. Corrosion behaviours were evaluated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization methods. Experimental study revealed that the corrosion rate (CR) of CMM coatings decreased successively with increase in number of layers up to certain limit, and then started increased. Experimental findings demonstrated that CMM (NiTi) alloy coating having optimal configuration, represented as (NiTi)2.0/4.0/120 is approximately five times more corrosion resistant than its monolayer counterpart, deposited from the same bath for same duration. Development of coatings in layered pattern was confirmed by scanning electron microscopy (SEM) analyses. EDX and XRD techniques confirms the composition and phase structure of alloy coatings. The corrosion mechanism responsible for delayed corrosion of multilayer coatings has been explained, and experimental results are discussed. © Pleiades Publishing, Ltd. 2024. ISSN 2070-2051, Protection of Metals and Physical Chemistry of Surfaces, 2024, Vol. 60, No. 2, pp. 178–189. Pleiades Publishing, Ltd., 2024.Item Combined effect of multidirectional forging and heat treatment on erosion and corrosion behaviour of the Mg-Zn-Mn alloys(Korean Society of Mechanical Engineers, 2024) Anne, G.; Hegde, A.; Kudva, S.A.; Sharma, P.; Kumar, P.; Matapati, M.; Ramesh, S.; Sharma, S.S.Multidirectional forging (MDF) was successfully applied to the Mg-4Zn-1Mn alloy for five passes at 300 °C. The grain size of 5 pass MDF processed samples reached 18 ± 3 µm from 256 ± 6 µm, and ?-Mg, MgZn2 and MnZn13 peaks were observed. Further MDF processed samples were solution treated (ST) at 300 °C for 2 h and quenched in SAE 20W40 oil and followed by artificial ageing (A) at 170 °C for four different timings including 1.5 h, 2 h, 2.5 h and 3.5 h respectively. The peak hardness of 219 Hv (5 pass MDF + H sample) was found in 2h artificial ageing which is 3.1 times higher compared to counterpart homogenised samples. Improvement of mechanical properties was attributed to smaller grain size and precipitation strengthening as well as distribution of the secondary phases. The combined effect of MDF and heat treatment was analysed using solid particle erosion tests at 30° and 90° impact angles using alumina. It was observed that higher impact angle (90°) had more erosion rate in all conditions and 5 pass MDF + H samples exhibited better erosion (0.0001 mg/g) due to higher hardness. On the other hand, polarisation and electrochemical impedance spectroscopy measurements were used to assess the alloys’ corrosion behaviour. The 3 pass MDF + H sample was found to have a corrosion rate of 0.0235 mm/y, which is two times lower than the counterpart 3 pass MDF processed samples and sixteen times lower than the homogenised sample (0.3838 mm/y). This was primarily due to the secondary phases’ better distribution and smaller grain size. © The Korean Society of Mechanical Engineers and Springer-Verlag GmbH Germany, part of Springer Nature 2024.Item Magnetic field-induced codeposition of (Ni–Co) alloy coatings for better corrosion protection(SAGE Publications Ltd, 2025) Yathish Rai, T.; Hegde, A.This paper explores the benefit of induced magnetic field (B) in the co-deposition of (Ni–Co) alloy coatings for better corrosion protection. The phenomenon of magnetohydrodynamic (MHD) convection has been used as the tool to deposit (Ni–Co) alloy coatings of high corrosion protection from an electrolytic bath having low [Co+2] ions. Experimental studies demonstrated that under optimal conditions of magnetic field intensity (B), magneto-electrodeposited (MED) coatings, developed under parallel (