Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Dry sliding wear of epoxy/cenosphere syntactic foams(Elsevier Ltd, 2015) Manakari, V.; Parande, G.; Doddamani, M.; Gaitonde, V.N.; Siddhalingeshwar, I.G.; Kishore; Shunmugasamy, V.C.; Gupta, N.Abstract Dry sliding wear behavior of epoxy matrix syntactic foams filled with 20, 40 and 60 wt% fly ash cenosphere is reported based on response surface methodology. Empirical models are constructed and validated based on analysis of variance. Results show that syntactic foams have higher wear resistance than the matrix resin. Among the parameters studied, the applied normal load (F) had a prominent effect on wear rate, specific wear rate (ws) and coefficient of friction (?). With increasing F, the wear rate increased, whereas ws and ? decreased. With increase in filler content, the wear rate and ws decreased, while the ? increased. With increase in sliding velocity as well as sliding distance, the wear rate and ws show decreasing trends. Microscopy revealed broken cenospheres forming debris and extensive deformation marks on the wear surface. © 2015 Elsevier Ltd.Item Processing of cenosphere/HDPE syntactic foams using an industrial scale polymer injection molding machine(Elsevier Ltd, 2016) Bharath Kumar, B.R.; Doddamani, M.R.; Zeltmann, S.E.; Gupta, N.; Ramesh, M.R.; Ramakrishna, S.Rapid production of high quality components is the key to cost reduction in industrial applications. The present work is the first attempt of manufacturing syntactic foams, hollow particle filled lightweight composites, using an industrial scale injection molding machine. High density polyethylene (HDPE) is used as the matrix material and fly ash cenospheres are used as the filler. Development of syntactic foams with cenospheres serves dual purpose of beneficial utilization of industrial waste fly ash and reduction in the cost of the component. The pressure and temperature used in the injection molding process are optimized to minimize fracture of cenospheres and obtain complete mixing of cenospheres with HDPE. The optimized parameters are used for manufacturing syntactic foams with 20, 40 and 60 wt.% cenospheres. With increasing cenosphere content, density and strength reduce and modulus increases. Surface modification of constituents results in rise in strength with increasing filler content. A theoretical model based on a differential scheme is used to estimate the properties of cenospheres by conducting parametric studies because of inherent difficulties in direct measurement of cenosphere properties. The potential for using the optimized injection molding process is demonstrated by casting several industrial components. © 2015 Elsevier Ltd.Item Effect of particle surface treatment and blending method on flexural properties of injection-molded cenosphere/HDPE syntactic foams(Springer New York LLC barbara.b.bertram@gsk.com, 2016) Bharath Kumar, B.R.; Doddamani, M.R.; Zeltmann, S.E.; Gupta, N.; Uzma; Gurupadu, S.; Sailaja, R.R.N.The present work on cenosphere/high-density polyethylene (HDPE) syntactic foams aims at understanding the effect of surface treatment of cenospheres and functionalization of HDPE on flexural properties. Cenospheres are treated with silane, and HDPE is functionalized with 10 % dibutyl maleate. Effects of mechanical and Brabender mixing methods are also studied. Flexural test specimens are cast with 20, 40, and 60 wt% of cenospheres using injection molding. The flexural modulus and strength are found to increase with increasing cenosphere content. Particle breakage increases with the cenosphere content, and the measured properties show increased dependence on processing method. Brabender mixing resulted in 70 and 41 % higher modulus and strength for 60 wt% cenospheres than HDPE. Modulus of syntactic foams is predicted by two theoretical models. Bardella–Genna model provides close estimates for syntactic foams having 20 and 40 wt% cenospheres, while predictions are higher for higher cenosphere content, likely due to particle breakage during processing. The uncertainty in the properties of cenospheres due to defects contributes to the variation in the predicted values. © 2015, Springer Science+Business Media New York.Item Effect of cenosphere surface treatment and blending method on the tensile properties of thermoplastic matrix syntactic foams(John Wiley and Sons Inc. P.O.Box 18667 Newark NJ 07191-8667, 2016) Bharath Kumar, B.R.; Zeltmann, S.E.; Doddamani, M.R.; Gupta, N.; Uzma; Gurupadu, S.; Sailaja, R.R.N.The influence of cenosphere surface treatment and blending method on the properties of injection molded high-density polyethylene (HDPE) matrix syntactic foams is investigated. Cenospheres are treated with silane and HDPE is functionalized with dibutyl maleate. Tensile test specimens are cast with 20, 40, and 60 wt % of cenospheres using injection molding. Modulus and strength are found to increase with increasing cenosphere content for composites with treated constituents. Highest modulus and strength were observed for 40 and 60 wt % untreated mechanically mixed and treated brabender mixed cenospheres/HDPE blends, respectively. These values are 37 and 17% higher than those for virgin and functionalized HDPE. Theoretical models are used to assess the effect of particle properties and interfacial bonding on modulus and strength of syntactic foams. Brabender mixing method provided highest ultimate tensile and fracture strengths, which is attributed to the effectiveness of Brabender in breaking particle clusters and generating the higher particle–matrix surface area compared to that by mechanical mixing method. Theoretical trends show clear benefits of improved particle–matrix interfacial bonding in the strength results. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43881. © 2016 Wiley Periodicals, Inc.Item Development of glass microballoon/HDPE syntactic foams by compression molding(Elsevier Ltd, 2017) Jayavardhan, M.L.; Bharath Kumar, B.R.; Doddamani, M.; Singh, A.K.; Zeltmann, S.E.; Gupta, N.Thermoplastic resins are widely used in consumer products and industrial components. There is a significant interest in weight reduction of many of those components. Although glass hollow particle filled lightweight syntactic foams with thermoset matrices have been studied in detail, studies on thermoplastic syntactic foams are scarce. The present study is focused on developing a compression molding based processing method for glass microballoon/high density polyethylene (GMB/HDPE) syntactic foams and studying their mechanical properties to develop structure-property correlations. Blending of GMB in HDPE is carried out using a Brabender mixer with processing parameters optimized for minimal filler breakage. Flexural and tensile test specimens are compression molded with 20, 40 and 60 vol% of GMB. Particle fracture increases with increasing GMB content due to increased particle to particle interaction during processing. Additionally, increasing wall thickness makes GMBs stronger and results in reduced particle fracture. Flexural modulus increases while strength decreases with increasing filler content. Tensile strength decreases with increasing filler content, while tensile modulus is relatively unchanged. GMB volume fraction has a more prominent effect than the wall thickness on the mechanical properties of syntactic foams. Specific moduli of GMB/HDPE foams are superior while specific strength is comparable to neat HDPE. © 2017 Elsevier LtdItem Influence of materials and machining parameters on drilling performance of syntactic foams(ASTM International, 2018) Ashrith, H.S.; Doddamani, M.; Gaitonde, V.N.; Gupta, N.The effects of drilling parameters and material properties are investigated on epoxy matrix syntactic foams reinforced with 20, 40, and 60 volume percent glass microballoon. The influences of cutting speed, feed, drill diameter, and filler content on drilling performance are studied based on the full factorial design of experiments using tungsten carbide twist drills. Based on experimental results, machinability aspects within the range of the chosen input parameters are predicted using response surface methodology-based models, which can guide industrial practitioners for choosing the appropriate process parameters. Microscopy is conducted on the drilled specimens to understand crack initiation and propagation mechanisms. The thrust force and specific cutting coefficient of syntactic foam are 40 % lower as compared to those of neat epoxy. The surface roughness of syntactic foams is higher than that of neat epoxy. The micrographs of drill bits show negligible tool wear. These results show the possibility of using syntactic foams in industrial applications in which the drilling of material is required for reasons such as joining using bolts. © © 2018 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959Item Buckling and free vibration behavior of cenosphere/epoxy syntactic foams under axial compressive loading(ASTM International, 2018) Waddar, S.; Jeyaraj, P.; Doddamani, M.; Gupta, N.The buckling and free vibration behavior of cenosphere/epoxy syntactic foams under axial compressive loading are investigated experimentally in this work. The buckling load is obtained from the load-deflection curve based on the Double Tangent Method (DTM) and Modified Budiansky Criteria (MBC). Furthermore, the influence of an axial compression load on the natural frequencies associated with the first three transverse bending modes is analyzed. Finally, the buckling loads predicted using DTM and MBC are compared to the buckling load calculated based on the vibration correlation technique. It is observed that the buckling loads predicted through the three different methods are in close agreement. The experimental results revealed that the buckling load and natural frequency of the syntactic foams increase with the cenosphere volume fraction. It is observed that the natural frequencies reduce with increases in the axial compression load for all the modes. However, a rapid increase in the fundamental frequency is observed when the compressive load is near and beyond the critical buckling load. © © 2018 by ASTM International.Item Additive Manufacturing of Three-Phase Syntactic Foams Containing Glass Microballoons and Air Pores(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2019) Singh, A.K.; Deptula, A.J.; Anawal, R.; Doddamani, M.; Gupta, N.High-density polyethylene and its syntactic foams reinforced with 20 vol.% and 40 vol.% glass microballoons were 3D printed using the fused filament fabrication method and studied for their compressive response. The three-phase microstructure of syntactic foams fabricated in this work also contained about 10 vol.% matrix porosity for obtaining light weight for buoyancy applications. Filaments for 3D printing were developed using a single screw filament extruder and printed on a commercial 3D printer using settings optimized in this work. Three-dimensional printed blanks were machined to obtain specimens that were tested at 10 ?4 s ?1 , 10 ?3 s ?1 , 10 ?2 s ?1 and 1 s ?1 strain rates. The compression results were compared with those of compression-molded (CM) specimens of the same materials. It was observed that the syntactic foam had a three-phase microstructure: matrix, microballoons and air voids. The air voids made the resulting foam lighter than the CM specimen. The moduli of the 3D-printed specimen were higher than those of the CM specimens at all strain rates. Yield strength was observed to be higher for CM samples than 3D-printed ones. © 2019, The Minerals, Metals & Materials Society.