Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Processing of cenosphere/HDPE syntactic foams using an industrial scale polymer injection molding machine(Elsevier Ltd, 2016) Bharath Kumar, B.R.; Doddamani, M.R.; Zeltmann, S.E.; Gupta, N.; Ramesh, M.R.; Ramakrishna, S.Rapid production of high quality components is the key to cost reduction in industrial applications. The present work is the first attempt of manufacturing syntactic foams, hollow particle filled lightweight composites, using an industrial scale injection molding machine. High density polyethylene (HDPE) is used as the matrix material and fly ash cenospheres are used as the filler. Development of syntactic foams with cenospheres serves dual purpose of beneficial utilization of industrial waste fly ash and reduction in the cost of the component. The pressure and temperature used in the injection molding process are optimized to minimize fracture of cenospheres and obtain complete mixing of cenospheres with HDPE. The optimized parameters are used for manufacturing syntactic foams with 20, 40 and 60 wt.% cenospheres. With increasing cenosphere content, density and strength reduce and modulus increases. Surface modification of constituents results in rise in strength with increasing filler content. A theoretical model based on a differential scheme is used to estimate the properties of cenospheres by conducting parametric studies because of inherent difficulties in direct measurement of cenosphere properties. The potential for using the optimized injection molding process is demonstrated by casting several industrial components. © 2015 Elsevier Ltd.Item Prediction of strain rate sensitivity of high density polyethylene using integral transform of dynamic mechanical analysis data(Elsevier Ltd, 2016) Zeltmann, S.E.; Bharath Kumar, B.R.; Doddamani, M.R.; Gupta, N.Recent interest in understanding the effect of strain rate on mechanical properties has motivated this study to develop a correlation between frequency domain dynamic mechanical analysis (DMA) results and elastic modulus values that are obtained from a separate set of elaborate tensile tests conducted over a wide range of strain rates. Using the time-temperature superposition principle and the integral relations of viscoelasticity, the DMA results are converted into a time-domain relaxation function in order to predict the strain-rate dependent modulus. The transformation technique is validated with experimental results for high density polyethylene (HDPE) resin and is found to be accurate over a wide range of strain rates. Cross correlation between DMA results and tensile test results over a wide range of strain rates can help in substantially reducing the requirement for tests that are needed to characterize the material behavior with respect to strain rates, temperature and loading frequency. © 2016 Elsevier LtdItem Additive Manufacturing of Syntactic Foams: Part 2: Specimen Printing and Mechanical Property Characterization(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2018) Singh, A.K.; Saltonstall, B.; Patil, B.; Hoffmann, N.; Doddamani, M.; Gupta, N.High-density polyethylene (HDPE) and its fly ash cenosphere-filled syntactic foam filaments have been recently developed. These filaments are used for three-dimensional (3D) printing using a commercial printer. The developed syntactic foam filament (HDPE40) contains 40 wt.% cenospheres in the HDPE matrix. Printing parameters for HDPE and HDPE40 were optimized for use in widely available commercial printers, and specimens were three-dimensionally (3D) printed for tensile testing at strain rate of 10?3 s?1. Process optimization resulted in smooth operation of the 3D printer without nozzle clogging or cenosphere fracture during the printing process. Characterization results revealed that the tensile modulus values of 3D-printed HDPE and HDPE40 specimens were higher than those of injection-molded specimens, while the tensile strength was comparable, but the fracture strain and density were lower. © 2018, The Minerals, Metals & Materials Society.Item Additive Manufacturing of Syntactic Foams: Part 1: Development, Properties, and Recycling Potential of Filaments(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2018) Singh, A.K.; Patil, B.; Hoffmann, N.; Saltonstall, B.; Doddamani, M.; Gupta, N.This work focuses on developing filaments of high-density polyethylene (HDPE) and their hollow particle-filled syntactic foams for commercial three-dimensional (3D) printers based on fused filament fabrication technology. Hollow fly-ash cenospheres were blended by 40 wt.% in a HDPE matrix to produce syntactic foam (HDPE40) filaments. Further, the recycling potential was studied by pelletizing the filaments again to extrude twice (2×) and three times (3×). The filaments were tensile tested at 10?4 s?1, 10?3 s?1, and 10?2 s?1 strain rates. HDPE40 filaments show an increasing trend in modulus and strength with the strain rate. Higher density and modulus were noticed for 2× filaments compared to 1× filaments because of the crushing of some cenospheres in the extrusion cycle. However, 2× and 3× filament densities are nearly the same, showing potential for recycling them. The filaments show better properties than the same materials processed by conventional injection molding. Micro-CT scans show a uniform dispersion of cenospheres in all filaments. © 2018, The Minerals, Metals & Materials Society.