Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
3 results
Search Results
Item Experimental studies on cyclic variations in a single cylinder diesel engine fuelled with raw biogas by dual mode of operation(Elsevier Ltd, 2020) Jagadish, C.; Gumtapure, V.In this research work, cycle-by-cycle variations of a single cylinder, diesel engine operated with raw biogas is investigated. The biogas used to run the engine is obtained from food waste and as the composition of 88.10%-CH4 + 11.895%-CO2. To study the combustion characteristics, the naturally aspirated diesel engine is converted into dual mode by inducting the biogas into the intake manifold for different proportions from BG20 to BG60 with a step of 10% is mixed with air (i.e. BG60-60% of biogas by mass) respectively. Combustion parameters are measured and recorded by the means of the data acquisition system (DAQ) for 100 combustion cycle. By determining the parameters such as standard deviation, coefficient of variation and return map, the cycle variability is analyzed. From the experimental result, it is observed that as the engine is operated at higher loads and as the biogas is increased from BG20 to BG60 the cyclic variations for maximum cylinder pressure (Pmax) and indicated mean effective pressure (IMEP) increases. Coefficient of variation of Pmax for BG20 and BG40 is lower by 2.3% and 11.98% as compared to diesel. From time return map, BG40 showed good combustion stability and lesser NOx emission compared to diesel. © 2020 Elsevier LtdItem Experimental investigation of methane-enriched biogas in a single cylinder diesel engine by the dual fuel mode(Taylor and Francis Ltd., 2022) Chandrashekar, J.; Gumtapure, V.In this experimental work characteristic such as performance, combustion and emission of a single cylinder, four-stroke constant speed, direct injection, water-cooled diesel engine is investigated. The engine is operated by dual fuel mode using methane-enriched biogas (88.10%-CH4 + 11.89%-CO2) obtained from the food waste. Biogas (BG) is inducted into the engine at intake manifold with various mixtures like BG20, BG30 and BG40 mixed with air (i.e. BG40-40% of CH4 by mass respectively) at actual injection timing of 27.5° before top dead centre (bTDC) for different loads. The performance, combustion and emission characteristics of the engine operated by dual fuel mode were experimentally investigated, and compared with respect to diesel. By observing the experimental results, BG40 was optimized on the basis of lesser emissions and improved performance. BG40 showed lesser brake thermal efficiency and higher brake specific energy consumption than BG20 and BG30 for all loads. On the other hand, BG40 showed lower BTE by 15.5% and 15.62% compared to diesel at 3/4th and full load. Whereas the cylinder peak pressure for BG40 is higher than diesel by 5.36% and the net heat release rate is 14.9% higher than the diesel at full load. BG40 emitted higher carbon monoxide (CO) emissions than diesel by 5% at full load. The nitrogen oxide (NOx) emission for BG40 was lesser by 26.60% than diesel at full load, whereas the soot emission was 22.71% lower than diesel at full load respectively. © 2022 Taylor & Francis Group, LLC.Item Experimental Study on the Effect of Injection Timing on a Dual Fuel Diesel Engine Operated With Biogas Derived From Food Waste(American Society of Mechanical Engineers (ASME), 2022) Chandrashekar, J.; Gumtapure, V.The present work emphasizes the effects of injection timing on the characteristics of a 5.2-kW powered four-stroke diesel engine using biogas and its heat loss analysis. The biogas is obtained from food waste consisting of methane (CH4)-88.1% and carbon dioxide (CO2)-11.8% as the composition. The biogas (BG) is selected by mass basis ranging from 20% to 60% with 10% increments and is used to operate the engine by dual-fuel mode. The effect of three injection timings such as 25.5 deg (retarded), 27.5 deg (actual), and 29.5 deg (advanced) before top-dead center (bTDC) under dual-mode operation to enhance the properties of the engine is studied, and the results are compared with diesel mode at actual injection timing. Maximum brake thermal efficiency of 30.1% was observed for BG20 operated at 29.5-deg bTDC injection timing (IT). The dual mode operated at the injection timing of 29.5-deg bTDC showed an increase in cylinder pressure compared to diesel by 11.9% at full load conditions, whereas carbon monoxide emission was lower by 5.2% at 29.5-deg bTDC IT than diesel, and nitrogen oxide emission was lower at 25.5 deg bTDC IT than diesel mode by 45%. Besides, at 75% engine load, the least amount of heat losses was observed for BG50 exhibiting effective conversion of fuel energy into equivalent work higher than that of diesel by 2.2%, respectively. © © 2022 by ASME.