Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
15 results
Search Results
Item Microstructure and mechanical properties of magnesium alloy processed by equal channel angular pressing (ECAP)(Elsevier Ltd, 2017) Gopi, K.R.; Shivananda Nayaka, H.Equal Channel Angular Pressing (ECAP) with different passes was carried out for Mg-Al-Mn (AM) series magnesium alloy to investigate the microstructure and mechanical properties. ECAP process was carried up to 4 passes using route BC, where the samples are rotated by 90° in the same direction between consecutive passes. Microstructures were studied using optical microscope (OM) and scanning electron microscope (SEM) and it was observed that the grain size was reduced from 100 μm to 1 μm after 4 passes. Tensile test was conducted and the ultimate tensile strength (UTS) increased up to 2 passes but decreased with higher passes, even though grain size became finer with increase in ECAP passes. Microhardness was carried out and it was observed that the hardness was increased up to 2 passes of ECAP and decreased with higher passes. © 2017 Elsevier Ltd.Item Influence of Multi Axial Forging (MAF) on Microstructure and Mechanical Properties of Cu-Ti Alloy(Elsevier Ltd, 2018) Ramesh, S.; Shivananda Nayaka, H.S.; Gopi, K.R.Multi axial forging (MAF) is one among the severe plastic deformation (SPD) processes, where large strains are imposed into the component. In the present work, as-received Cu-1.5%Ti alloy was subjected to MAF for 2 and 4 cycles at room temperature. Microstructure showed grain refinement after 2 and 4 cycles. Average grain size obtained for MAF processed samples after 2 and 4 cycles are 120 μm and 40 μm, respectively compared to initial grain size of 800 μm. The Mechanical properties were analyzed for as-received and MAF processed samples. Tensile test showed increased ultimate tensile strength (493 MPa) for MAF 4-cycle sample compared to as-received (191 MPa) condition with accumulated strain of 2.18 for 4 cycles. Increase in hardness was observed for MAF processed sample of 143 Hv for 4-cycle compared to as-received sample of 67 Hv. © 2018 Elsevier Ltd.Item Influence of cold rolling process on microstructure and mechanical properties of Cu-1.5%Ti alloy(American Institute of Physics Inc. subs@aip.org, 2018) Ramesh, S.; Shivananda Nayaka, H.S.; Anne, G.; Gopi, K.R.The effects of cold rolling on the microstructure evolution and mechanical properties of Cu-1.5%Ti alloy were investigated. The results showed that the tensile strength of the Cu-1.5%Ti alloy increased with an increase of rolling deformation at room temperature. Significant grain refinement took place during rolling process revealed in optical microstructure and transmission electron microscope analysis. XRD patterns revealed peaks indexed to Cu, Cu3-Ti2 and Cu4-Ti3 after 8-pass rolling process. Microhardness of the rolled Cu-1.5%Ti alloy layers increased incessantly with increase in the number of rolling passes. Tensile strength increased up to 294 MPa which was about 1.54 times higher than that of the cast Cu-1.5%Ti alloy. Fracture surfaces of the rolled Cu-1.5%Ti alloy revealed the dimples in the structure, which is an indication of ductile fracture. © 2018 Author(s).Item Electrochemical Behaviour of ECAP-Processed AM Series Magnesium Alloy(Springer International Publishing, 2019) Gopi, K.R.; Shivananda Nayaka, H.Equal channel angular pressing (ECAP) is a technique for inducing high strain into the material to achieve ultrafine grain refinement. AM80 magnesium was processed by ECAP with processing route BC. ECAP-processed samples were tested for microstructural studies and electrochemical measurements. Potentiodynamic polarization test revealed decrease in corrosion current density due to uniform refined microstructure of the processed samples. Increment in charge transfer resistance (Rt) was observed for ECAPed samples with increase in capacitive arc diameters in Nyquist plots showing increased corrosion resistance in comparison with as-cast condition. The increment in corrosion resistance is because of grain refinement and uniform dispersal of intermetallic particles, which improved development of protective layer and bonding due to increased grain boundary density by ECAP process. © 2019, The Minerals, Metals & Materials Society.Item Investigation of Microstructure and Mechanical Properties of ECAP-Processed AM Series Magnesium Alloy(Springer New York LLC barbara.b.bertram@gsk.com, 2016) Gopi, K.R.; Shivananda Nayaka, H.S.; Sahu, S.Magnesium alloy Mg-Al-Mn (AM70) was processed by equal channel angular pressing (ECAP) at 275 °C for up to 4 passes in order to produce ultrafine-grained microstructure and improve its mechanical properties. ECAP-processed samples were characterized for microstructural analysis using optical microscopy, scanning electron microscopy, and transmission electron microscopy. Microstructural analysis showed that, with an increase in the number of ECAP passes, grains refined and grain size reduced from an average of 45 to 1 µm. Electron backscatter diffraction analysis showed the transition from low angle grain boundaries to high angle grain boundaries in ECAP 4 pass sample as compared to as-cast sample. The strength and hardness values an showed increasing trend for the initial 2 passes of ECAP processing and then started decreasing with further increase in the number of ECAP passes, even though the grain size continued to decrease in all the successive ECAP passes. However, the strength and hardness values still remained quite high when compared to the initial condition. This behavior was found to be correlated with texture modification in the material as a result of ECAP processing. © 2016, ASM International.Item Tribological and corrosion properties of AM70 magnesium alloy processed by equal channel angular pressing(Cambridge University Press, 2017) Gopi, K.R.; Shivananda Nayaka, H.Wear and corrosion properties of AM70 magnesium alloy subjected to equal channel angular pressing (ECAP) were investigated using pin-on-disc dry sliding wear test and electrochemical impedance spectroscopy (EIS), respectively. Wear test was conducted with 30 and 40 N loads with sliding distance of 5000 m and at a constant speed of 3 m/s. Reduced coefficient of friction (COF) and wear mass loss of ECAP processed samples showed increased wear resistance. Worn surface analysis by scanning electron microscope (SEM) showed the presence of delamination, wear debris, and plowing. Energy dispersive X-ray spectrometer (EDS) revealed the occurrence of oxidation, and the wear mechanism was identified as abrasion and oxidation wear. EIS plots showed the improvement in corrosion resistance of ECAP processed magnesium alloy compared to initial condition due to grain refinement and homogeneous distribution of secondary particles. © Materials Research Society 2017.Item Wear Properties of ECAP-Processed AM80 Magnesium Alloy(Springer New York LLC barbara.b.bertram@gsk.com, 2017) Gopi, K.R.; Shivananda Nayaka, H.; Sahu, S.AM80 magnesium alloy was subjected to equal-channel angular pressing (ECAP), and microstructural evolution was studied using scanning electron microscope (SEM). Grain size was found to decrease up to 3 µm after four passes. An increase in number of ECAP passes led to a corresponding increase in hardness of the processed samples. Unprocessed and ECAP-processed samples were subjected to wear test using pin-on-disk wear test machine to study the wear behavior. Effects of varying loads (30 and 40 N) with sliding distances (2500 and 5000 m) were studied. The results showed reduction in wear mass loss for the ECAP-processed samples in comparison with unprocessed condition. Coefficient of friction (COF) was studied for different loads, and improvement in COF values was observed for ECAP-processed samples compared to unprocessed condition. Worn surfaces were studied using SEM and energy-dispersive x-ray spectrometer, and they exhibited plastic deformation, delamination, plowing, wear debris and oxidation in the sliding direction. X-ray diffraction analysis was conducted on the worn surfaces to identify the phases. It revealed the presence of magnesium oxide and magnesium aluminum oxide which led to oxidation wear in the sliding direction. Wear mechanism was found to be abrasive and oxidation wear. © 2017, ASM International.Item Microstructural Evolution and Strengthening of AM90 Magnesium Alloy Processed by ECAP(Springer Verlag, 2017) Gopi, K.R.; Shivananda Nayaka, H.S.; Sahu, S.Equal-channel angular pressing (ECAP) was applied on AM90 magnesium alloy using processing route B C at 275?C up to four passes. Microstructural evolution and the corresponding modification in mechanical properties (strength, elongation and hardness) corresponding to the number of ECAP passes were evaluated using X-ray diffraction (XRD), electron backscatter diffraction, scanning electron microscopy, transmission electron microscopy, tensile test and microhardness test. Shear deformation was found to refine the microstructure by breaking it into smaller grains formed by dislocation reconstruction. Tensile strength and hardness were found to increase by ? 128 and 23%, respectively, for ECAP-processed 2-pass sample in comparison with that of the homogenized condition. After two passes, tensile strength and hardness started decreasing even though the grain size was still decreasing, which was found to be associated with texture modification during ECAP processing as observed by XRD analysis. © 2017, King Fahd University of Petroleum & Minerals.Item Corrosion Behavior of ECAP-Processed AM90 Magnesium Alloy(Springer Verlag, 2018) Gopi, K.R.; Shivananda Nayaka, H.; Sahu, S.Magnesium AM90 alloy was subjected to equal-channel angular pressing (ECAP) using route B C. Microstructural characterization revealed refined grains having average grain size ?3?m after ECAP 4 passes. Samples were subjected to electrochemical measurements to study the corrosion behavior. Potentiodynamic polarization test showed reduced corrosion current density (Icorr) for processed samples up to ECAP 3 pass due to grain refinement. Electrochemical impedance spectroscopy showed an increase in the diameter of the capacitive arcs and charge-transfer resistance (Rt) for ECAP-processed 3 pass sample indicating the reduction in corrosion rate. Increase in corrosion resistance is due to refined microstructure and uniform distribution of secondary particles forming a protective passivation layer (Mg (OH) 2) on the sample’s surface. Immersion test indicated lower hydrogen evolution from ECAP-processed samples compared to the unprocessed condition indicating decreased corrosion rate. © 2018, King Fahd University of Petroleum & Minerals.Item Numerical Simulation of Shot Peening Process on Equal Channel Angular Pressed Magnesium Alloy(Springer Netherlands rbk@louisiana.edu, 2018) Praveen, T.R.; Gopi, K.R.; Shivananda Nayaka, H.This paper presents the numerical simulation of inducing residual stresses on equal channel angular pressed (ECAP) magnesium alloy by shot peening process. Mg-Al-Mn (AM) series magnesium alloy was ECAP processed up to 4 passes using route BC. Microstructures were analysed and grain size reduced from 100 µm for the as-received sample to 3 µm for ECAP 4 pass sample. Tensile test was carried out and maximum tensile strength was found in ECAP 2 pass sample and decreased with higher ECAP passes. Grain refinement was characterized by optical microscopy, electron backscatter diffraction analysis (EBSD) and X-ray diffraction (XRD). Material (tensile) behaviour of 2 pass sample was implemented for finite element modelling. A finite element method was used to estimate the intensity of residual stresses developed due to shot peening in ECAP processed AM80 alloy. Simulation was done with different boundary condition such as impact velocity, geometry of shot-peen media, angle of impact and multiple impacts. The results are presented and the relationship between process parameters and the intensity of residual stresses are discussed. Increase in velocity of shot peening media showed an increase in the magnitude of residual stresses. Change in geometry of shot media altered the contact area between target and shot media during impact which influenced the magnitude of residual stresses and coverage area. The magnitude of residual stresses varied with the angle of impact and the multiple repeated impacts showed that the effective depth of residual stresses increased with the number of impacts. © 2018, Springer Science+Business Media B.V., part of Springer Nature.