Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Chemical-resistant Ultrafine Poly(styrene-co-acrylonitrile) Fibers by Electrospinning: Process Optimization by Design of Experiment(2013) Senthil, T.; George, G.; Anandhan, S.The effects of solution and processing parameters on the morphology and diameter of electrospun poly(styrene-co-acrylonitrile) fibers were investigated by design of experiment. Morphology of the electrospun fiber mats were investigated by scanning electron microscopy. With increasing solution concentration, fiber morphology changed from that of a spindle-like beaded one to smooth, and the average fiber diameter increased from 96 to 876 nm. Average fiber diameter gradually increased with applied voltage; however, fiber morphology was only slightly influenced by flow rate. Regression analysis results reveal that solution concentration has the most significant impact on the average and standard deviation of fiber diameter. © 2013 Copyright Taylor and Francis Group, LLC.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Comparison of structural, spectral and magnetic properties of NiO nanofibers obtained by sol-gel electrospinning from two different polymeric binders(Elsevier Ltd, 2015) George, G.; Anandhan, S.NiO is a p-type semiconductor with wide band gap energy. In this study, nickel oxide nanofibers were fabricated by sol-gel electrospinning followed by high temperature calcination, using two sacrificial polymeric binders. Poly(2-ethyl-2-oxazoline) (PEtOx) in water and styrene-acrylonitrile random copolymer (SAN) in N,N- dimethylformamide (DMF) along with nickel (II) acetate tetrahydrate (NATH), as metal oxide precursor, were the two distinct polymeric systems used in this study. The morphological and structural properties of NiO fibers obtained from the aforementioned systems were compared with each other. The degradation behavior of the sacrificial polymeric binder imparted a significant effect on the properties of the obtained NiO fibers. The grain sizes and the activation energies for grain growth of NiO fibers from two systems were different. The non-stoichiometric NiO fibers obtained from the SAN/NATH system had a better ferromagnetic behavior as compared with that produced from the PEtOx/NATH system. This non-stoichiometry made a difference also in the optical band gap energies of the NiO nanofibers. © 2015 Elsevier Ltd.Item Morphological and structural characterisation of sol-gel electrospun Co3O4 nanofibres and their electro-catalytic behaviour(Royal Society of Chemistry, 2015) George, G.; Elias, L.; Hegde, A.C.; Anandhan, S.Evolution of hydrogen and oxygen are a crucial part of many renewable energy systems. The replacement of the essential and expensive components in such systems can reduce the capital cost and improve the effectiveness of those systems. In this study, Co3O4 nanofibres were fabricated from sol-gel assisted electrospun poly(styrene-co-acrylonitrile)/cobalt acetate tetrahydrate precursor composite fibres. The morphological and compositional features of the Co3O4 nanofibres obtained after calcination of the precursor nanofibers were studied using scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The results of X-ray diffraction study and Raman spectroscopy revealed that the average grain size of the fibres increased with the calcination temperature. Clear evidence of defects in the fibres was observed in ultraviolet-visible-near infrared and energy dispersive spectroscopic measurements. The electrocatalytic behaviour of Co3O4 nanofibres obtained at different calcination temperatures was studied using them for the water splitting reaction in an alkaline medium. The maximum efficiency in the hydrogen evolution reaction was achieved using the Co3O4 nanofibres obtained at the lowest calcination temperature, which had the highest surface area and the smallest grain size. © The Royal Society of Chemistry 2015.Item A comparative study on the physico-chemical properties of sol-gel electrospun cobalt oxide nanofibres from two different polymeric binders(Royal Society of Chemistry, 2015) George, G.; Anandhan, S.In this study, two different sacrificial polymeric binders, namely poly(2-ethyl-2-oxazoline) (PEtOx) and poly(styrene-co-acrylonitrile) (SAN) along with cobalt acetate tetrahydrate (CATH), as the metal oxide precursor, were used for the fabrication of Co3O4 nanofibres through sol-gel electrospinning. It was observed that the degradation behaviour and physical properties of SAN and PEtOx influenced the structure, morphology and spectral properties of Co3O4 nanofibres, as the properties of the nanofibres obtained from the aforementioned systems were compared with each other. The grain size, shape and the activation energies for grain growth of Co3O4 nanofibres obtained from these two polymeric systems were different. This difference in grain size and shape caused a difference in the optical band gap energies and the magnetic properties of the Co3O4 nanofibres. This study reveals that one can tailor the characteristics of cobalt oxide nanofibres by an appropriate selection of polymeric binders for sol-gel electrospinning. © The Royal Society of Chemistry.