Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
9 results
Search Results
Item Structural characterization of nano-crystalline Co3O4 ultra-fine fibers obtained by sol-gel electrospinning(2013) George, G.; Anandhan, S.In this paper, we report the obtention of ultrafine fibers of cobalt oxide (Co3O4) by combining electrospinning method with high-temperature calcinations from the precursor sol of poly(2-ethyl-2- oxazoline) (PEtOx)/cobalt acetate tetrahydrate [Co(CH3COO) 2·4H2O] in water. The optimum electrospinning conditions for obtaining precursor composite nanofibers from PEtOx/Co(CH 3COO)2·4H2O solution in water, to produce ceramic nanofibers, were studied. The average fiber diameter of the precursor composite fibers measured by scanning electron microscopy (SEM) was approximately 200 nm. Thermogravimetric analysis of PEtOx was performed to estimate the suitable calcination temperature of the precursor fibers. SEM images of the ceramic fibers obtained after calcination revealed the shrinkage in diameter due to complete degradation of the polymer and Co(CH 3COO)2·4H2O. Fourier transform infrared spectroscopy was used to ensure the complete pyrolysis of polymer during calcinations of the composite fibers. Crystalline properties of the ceramic fibers were studied by X-ray diffraction and high resolution transmission electron microscopy. The ceramic fibers are polycrystalline with an average grain size of ?40 nm obtained at a calcination temperature of 773 K. It was observed that the grain sizes increased as the calcination temperature was increased, due to self assembly mechanism. © 2013 Springer Science+Business Media New York.Item Synthesis and characterisation of nickel oxide nanofibre webs with alcohol sensing characteristics(Royal Society of Chemistry, 2014) George, G.; Anandhan, S.In this study, nickel oxide (NiO) nanofibres were obtained by a sol-gel electrospinning process followed by calcination from an aqueous sol of poly(2-ethyl-2-oxazoline)/nickel acetate tetrahydrate. Thermogravimetric analysis was used to determine the degradation temperature of the composite fibres, so as to get nickel oxide nanofibres. X-ray photoelectron spectroscopy and X-ray diffraction studies revealed the complete elimination of the organic phase from NiO fibres during calcination. The change in grain size with calcination temperature was determined by X-ray diffraction. The defects in fibres resulted in the modification of their Raman spectra as compared with that of a single crystal. The magnetic properties of the fibres were reduced as the calcination temperature was increased; this is due to the presence of non-stoichiometric defects. As the calcination temperature was increased, the amount of defects was reduced, which induced a difference in the band gap energy of the fibres. Sensitivity of the NiO fibres towards five different alcohols was studied, and the sensitivity towards ethanol was the highest. © The Royal Society of Chemistry 2014.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Comparison of structural, spectral and magnetic properties of NiO nanofibers obtained by sol-gel electrospinning from two different polymeric binders(Elsevier Ltd, 2015) George, G.; Anandhan, S.NiO is a p-type semiconductor with wide band gap energy. In this study, nickel oxide nanofibers were fabricated by sol-gel electrospinning followed by high temperature calcination, using two sacrificial polymeric binders. Poly(2-ethyl-2-oxazoline) (PEtOx) in water and styrene-acrylonitrile random copolymer (SAN) in N,N- dimethylformamide (DMF) along with nickel (II) acetate tetrahydrate (NATH), as metal oxide precursor, were the two distinct polymeric systems used in this study. The morphological and structural properties of NiO fibers obtained from the aforementioned systems were compared with each other. The degradation behavior of the sacrificial polymeric binder imparted a significant effect on the properties of the obtained NiO fibers. The grain sizes and the activation energies for grain growth of NiO fibers from two systems were different. The non-stoichiometric NiO fibers obtained from the SAN/NATH system had a better ferromagnetic behavior as compared with that produced from the PEtOx/NATH system. This non-stoichiometry made a difference also in the optical band gap energies of the NiO nanofibers. © 2015 Elsevier Ltd.Item Morphological and structural characterisation of sol-gel electrospun Co3O4 nanofibres and their electro-catalytic behaviour(Royal Society of Chemistry, 2015) George, G.; Elias, L.; Hegde, A.C.; Anandhan, S.Evolution of hydrogen and oxygen are a crucial part of many renewable energy systems. The replacement of the essential and expensive components in such systems can reduce the capital cost and improve the effectiveness of those systems. In this study, Co3O4 nanofibres were fabricated from sol-gel assisted electrospun poly(styrene-co-acrylonitrile)/cobalt acetate tetrahydrate precursor composite fibres. The morphological and compositional features of the Co3O4 nanofibres obtained after calcination of the precursor nanofibers were studied using scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The results of X-ray diffraction study and Raman spectroscopy revealed that the average grain size of the fibres increased with the calcination temperature. Clear evidence of defects in the fibres was observed in ultraviolet-visible-near infrared and energy dispersive spectroscopic measurements. The electrocatalytic behaviour of Co3O4 nanofibres obtained at different calcination temperatures was studied using them for the water splitting reaction in an alkaline medium. The maximum efficiency in the hydrogen evolution reaction was achieved using the Co3O4 nanofibres obtained at the lowest calcination temperature, which had the highest surface area and the smallest grain size. © The Royal Society of Chemistry 2015.Item A comparative study on the physico-chemical properties of sol-gel electrospun cobalt oxide nanofibres from two different polymeric binders(Royal Society of Chemistry, 2015) George, G.; Anandhan, S.In this study, two different sacrificial polymeric binders, namely poly(2-ethyl-2-oxazoline) (PEtOx) and poly(styrene-co-acrylonitrile) (SAN) along with cobalt acetate tetrahydrate (CATH), as the metal oxide precursor, were used for the fabrication of Co3O4 nanofibres through sol-gel electrospinning. It was observed that the degradation behaviour and physical properties of SAN and PEtOx influenced the structure, morphology and spectral properties of Co3O4 nanofibres, as the properties of the nanofibres obtained from the aforementioned systems were compared with each other. The grain size, shape and the activation energies for grain growth of Co3O4 nanofibres obtained from these two polymeric systems were different. This difference in grain size and shape caused a difference in the optical band gap energies and the magnetic properties of the Co3O4 nanofibres. This study reveals that one can tailor the characteristics of cobalt oxide nanofibres by an appropriate selection of polymeric binders for sol-gel electrospinning. © The Royal Society of Chemistry.Item Tuning characteristics of Co3O4 nanofiber mats developed for electrochemical sensing of glucose and H2O2(Elsevier B.V., 2016) George, G.; Anandhan, S.Nano-crystalline Co3O4 nanofibrous mats were fabricated by calcining the precursor nanofibers obtained by electrospinning of a sol comprising of a unique polymeric binder poly(2-ethyl-2-oxazoline) and cobalt acetate tetrahydrate in water. The influence of the calcination temperature used for the synthesis of the oxide nanofibers from the xerogel fibers on various physico-chemical properties of the former was studied. The Co3O4 nanofibers obtained at 400 °C had the highest electrochemical sensitivity towards glucose and H2O2. Further, the results prove that Co3O4 nanofibers can be used for the detection of glucose and H2O2 concurrently as the response times taken by these moieties are different. Therefore, one can differentiate the concentration of glucose and H2O2 by analyzing the signals obtained after the respective response time and this multiple sensitivity of Co3O4 can be applied in the field of biosensors. © 2016 Elsevier B.V.Item Understanding the interplay of solution and process parameters on the physico-chemical properties of ZnO nanofibers synthesized by sol-gel electrospinning(Institute of Physics, 2023) Prabhu, N.N.; Rajendra, B.V.; Anandhan, S.; Murthy, K.; Jagadeesh Chandra, R.B.; George, G.; Kumar, B.; Shivamurty, B.Aging populations and the increase in chronic diseases worldwide demand efficient healthcare tools for simple, rapid, and accurate diagnosis and monitoring the human health. In this context, gas sensors are used to analyze the type of gas in the breath to diagnose chronic diseases. Metal oxide and ceramic nanofibers (NFs) produced by the electrospinning (ES) method have been investigated for potential use as gas sensors in the engineering and medical sectors. The material and process parameters are the main influencing factors on the functional performance of electrospun metal oxide NFs. Zinc oxide (ZnO) based NFs are used in various gas sensors due to the wide band gap (3.37eV), large exciton binding energy, and high mobility of charge carriers of ZnO. In this research, we made an attempt to study the effect of poly(vinyl alcohol) (PVA) and zinc acetate dihydrate (ZnAc2) concentrations and feed rate, voltage, spinneret tip-to-collector distance (TCD), and pyrolysis temperature on the physical properties of ZnO NFs. An average fiber diameter of 119 nm was obtained after pyrolysis at 600 °C of electrospun fiber produced from an aqueous PVA solution of concentration 15 w% with 7.5 w% ZnAc2 based on the weight of PVA. The grain size, transmittance, structural defects, and band gap energy of NFs were found to increase as a function of the pyrolysis temperature, which could be beneficial for the functional applications of these NFs. © 2023 The Author(s). Published by IOP Publishing Ltd