Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item Parametric study of manufacturing ultrafine polybenzimidazole fibers by electrospinning(Springer, 2012) Anandhan, S.; Ponprapakaran, K.; Senthil, T.; George, G.Polybenzimidazole (PBI), a high performance polymer, was synthesized from 3,3?-diaminobenzidine (DAB) and isophthalic acid (IPA) through polycondensation. The chemical structure of PBI was confirmed by Fourier transform infrared spectroscopy. Thermal characterization of PBI was done by thermogravimetry and differential scanning calorimetry. PBI nanofibers were fabricated by electrospinning of N, N-dimethyl acetamide solutions of PBI of different solution concentrations, at different voltages. The effects of solution and process parameters (namely, solution concentration and DC voltage) on morphology and average diameter of electrospun PBI fibers were investigated. The electrospun ultrafine fibers' diameter and morphology were characterized by using scanning electron microscopy. Nanofibers were obtained only from PBI solutions of concentrations 12 and 14 % (w/v). At concentrations of 8, 10, and 16 %, fibers could not be obtained. The process parameters were optimized by using the statistical tool, factorial or two-way ANOVA (analysis of variance), DOE (design of experiments) and the results indicate that the applied voltage and the interaction of voltage and solution concentration are influential in determining the diameter and morphology of the electrospun ultrathin PBI fibers. Electrospun PBI fibers, as small as 56 nm, could be successfully produced by using the right combination of solution concentration and spinning voltage. © 2012 Central Institute of Plastics Engineering & Technology.Item Structural characterization of nano-crystalline Co3O4 ultra-fine fibers obtained by sol-gel electrospinning(2013) George, G.; Anandhan, S.In this paper, we report the obtention of ultrafine fibers of cobalt oxide (Co3O4) by combining electrospinning method with high-temperature calcinations from the precursor sol of poly(2-ethyl-2- oxazoline) (PEtOx)/cobalt acetate tetrahydrate [Co(CH3COO) 2·4H2O] in water. The optimum electrospinning conditions for obtaining precursor composite nanofibers from PEtOx/Co(CH 3COO)2·4H2O solution in water, to produce ceramic nanofibers, were studied. The average fiber diameter of the precursor composite fibers measured by scanning electron microscopy (SEM) was approximately 200 nm. Thermogravimetric analysis of PEtOx was performed to estimate the suitable calcination temperature of the precursor fibers. SEM images of the ceramic fibers obtained after calcination revealed the shrinkage in diameter due to complete degradation of the polymer and Co(CH 3COO)2·4H2O. Fourier transform infrared spectroscopy was used to ensure the complete pyrolysis of polymer during calcinations of the composite fibers. Crystalline properties of the ceramic fibers were studied by X-ray diffraction and high resolution transmission electron microscopy. The ceramic fibers are polycrystalline with an average grain size of ?40 nm obtained at a calcination temperature of 773 K. It was observed that the grain sizes increased as the calcination temperature was increased, due to self assembly mechanism. © 2013 Springer Science+Business Media New York.Item Influence of nano-aluminum-hydroxide on tribological, mechanical and flammability properties of E-glass fabric/epoxy multi-layered laminates(Huthig GmbH, 2014) Shivamurty, B.; George, G.; Bhat, K.U.; Anandhan, S.E-glass fabric/nano aluminum hydroxide (ATH)/epoxy composites were prepared by manual lay-up and compression molding. An image processing tool was used to quantify fineness of dispersion of nano-ATH particles in epoxy. Fourier transform infrared (FTIR) spectroscopy was used to understand the interaction between nano-ATH and epoxy. Mechanical properties, sliding wear resistance and fire retardance of these composites improved upon addition of nano-ATH. The composite containing 0.125 wt% of nano-ATH exhibited optimum mechanical properties and low specific wear rate.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Morphological and structural characterisation of sol-gel electrospun Co3O4 nanofibres and their electro-catalytic behaviour(Royal Society of Chemistry, 2015) George, G.; Elias, L.; Hegde, A.C.; Anandhan, S.Evolution of hydrogen and oxygen are a crucial part of many renewable energy systems. The replacement of the essential and expensive components in such systems can reduce the capital cost and improve the effectiveness of those systems. In this study, Co3O4 nanofibres were fabricated from sol-gel assisted electrospun poly(styrene-co-acrylonitrile)/cobalt acetate tetrahydrate precursor composite fibres. The morphological and compositional features of the Co3O4 nanofibres obtained after calcination of the precursor nanofibers were studied using scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The results of X-ray diffraction study and Raman spectroscopy revealed that the average grain size of the fibres increased with the calcination temperature. Clear evidence of defects in the fibres was observed in ultraviolet-visible-near infrared and energy dispersive spectroscopic measurements. The electrocatalytic behaviour of Co3O4 nanofibres obtained at different calcination temperatures was studied using them for the water splitting reaction in an alkaline medium. The maximum efficiency in the hydrogen evolution reaction was achieved using the Co3O4 nanofibres obtained at the lowest calcination temperature, which had the highest surface area and the smallest grain size. © The Royal Society of Chemistry 2015.Item Structure-property relationship of halloysite nanotubes/ethylene-vinyl acetate-carbon monoxide terpolymer nanocomposites(SAGE Publications Ltd info@sagepub.co.uk, 2017) George, G.; SelvaKumar, M.; Mahendran, A.; Anandhan, S.Poly(ethylene-co-vinyl acetate-co-carbon monoxide) (EVACO)/halloysite nanotube (HNT) nanocomposite films were solution cast. Dispersion of HNTs in the matrix was analyzed by elemental mapping and the role of HNTs on crystallizability, flammability and thermal, mechanical, and electrical properties of the polymer was evaluated. The nature of interaction between the EVACO matrix and HNTs was studied using Fourier transform infrared spectroscopy. The highest tensile strength was observed for the composite with 1% filler loading, whereas the highest crystallinity was observed for that with 3% filler loading. The decay in the tensile properties at higher filler loading was due to agglomeration of HNTs and debonding of polymer-filler interface. The electrical volume resistivity of the composites decreased with HNT loading because of the ionic charge transfer. The direct current electrical resistivity study of the composites proves that the addition of HNT can improve the antistatic properties of the polymer. © The Author(s) 2015.