Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Use of nano-ATH as a multi-functional additive for poly(ethylene-co-vinyl acetate-co-carbon monoxide)(Springer Verlag service@springer.de, 2014) George, G.; Mahendran, A.; Anandhan, S.Flame retardant aluminum hydroxide (ATH) nanoparticles of size ?10-20 nm were dispersed in ethylene-vinyl acetate-carbon monoxide terpolymer (EVACO) via solution casting. The effect of filler loading on the crystallizability, thermal, mechanical, flammability, optical and electrical properties of EVACO was evaluated. At 1 % filler loading nano-ATH particles exhibited very good dispersibility in the EVACO matrix and the % crystallinity of EVACO is the highest at this filler loading. The changes in crystallinity were studied by X-ray diffractometry and differential scanning calorimetry. The highest tensile strength was observed for the composite with 1 % nano-ATH loading, which has the best filler dispersion, and the decay in the tensile properties at higher filler loading is due to agglomerations of ATH nanoparticles and polymer-filler interface debonding. The UV absorption of these composites is augmented irrespective of the nano-ATH loading and ATH emerges as a good absorber of UV light. The DC electrical conductivity study of the composites proves that the addition nano-ATH is an efficient way to improve the dielectric properties of EVACO. The presence of nano-ATH improves the flame retardance of these composites. © 2014 Springer-Verlag Berlin Heidelberg.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Structure-property relationship of halloysite nanotubes/ethylene-vinyl acetate-carbon monoxide terpolymer nanocomposites(SAGE Publications Ltd info@sagepub.co.uk, 2017) George, G.; SelvaKumar, M.; Mahendran, A.; Anandhan, S.Poly(ethylene-co-vinyl acetate-co-carbon monoxide) (EVACO)/halloysite nanotube (HNT) nanocomposite films were solution cast. Dispersion of HNTs in the matrix was analyzed by elemental mapping and the role of HNTs on crystallizability, flammability and thermal, mechanical, and electrical properties of the polymer was evaluated. The nature of interaction between the EVACO matrix and HNTs was studied using Fourier transform infrared spectroscopy. The highest tensile strength was observed for the composite with 1% filler loading, whereas the highest crystallinity was observed for that with 3% filler loading. The decay in the tensile properties at higher filler loading was due to agglomeration of HNTs and debonding of polymer-filler interface. The electrical volume resistivity of the composites decreased with HNT loading because of the ionic charge transfer. The direct current electrical resistivity study of the composites proves that the addition of HNT can improve the antistatic properties of the polymer. © The Author(s) 2015.Item Influence of multiwalled carbon nanotubes on the structure and properties of poly(ethylene-co-vinyl acetate-co-carbon monoxide) nanocomposites(John Wiley and Sons Inc, 2021) George, G.; Mahendran, A.R.; SelvaKumar, S.; Anandhan, S.In this work, composites of poly(ethylene-co-vinyl acetate-co-carbon monoxide) (EVACO)/surface-modified multiwalled carbon nanotubes (m-MWCNTs) were prepared using a solution casting technique. Acid treatment was employed for the surface modification of MWCNTs to improve the compatibility between polar EVACO and MWCNTs. The influences of m-MWCNTs on the crystalline, mechanical, thermal, and electrical properties of EVACO at very low filler loading were systematically evaluated. The presence of m-MWCNTs in the EVACO matrix influenced the crystallinity, and the respective changes were determined and quantified using dynamic scanning calorimetry and X-ray diffraction. The mechanical properties of the composites were improved remarkably by the addition of a minute quantity (0.05, 0.1, 0.15, 0.2, and 0.25 wt%) of m-MWCNTs. Additionally, m-MWCNTs in the EVACO matrix improved the thermal stability and electrical properties of EVACO. However, the filler loading is below the threshold loading of the fillers, and there was no drastic improvement in the electrical conductivity of the composite. © 2021 Society of Plastics Engineers.