Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item A high efficiency on-chip reconfigurable Doherty power amplifier for LTE communication cells(John Wiley and Sons Inc. P.O.Box 18667 Newark NJ 07191-8667, 2018) Kumar, R.; Kanuajia, B.K.; Dwari, S.; Kumar, S.; Song, H.In this paper, a high efficiency on-chip reconfigurable Doherty power amplifier (DPA) with proposed topology is proposed for LTE or 4G communication cells. The proposed DPA consists of input driver topology, hybrid coupler, asymmetric amplifiers, and 1:1 balun filtered network. The proposed input driver circuit provides wide amplified signal operation within range of 2.3GHz to 6GHz with flat gain of 33 dB. The amplified signal is unsteadily divided into two paths toward the carrier and the power amplifier by 900 hybrid couplers and demonstrates 27.6 dB and 28.3 dB of gain along with 83.2% and 84.5% of power added efficiency at average output power of 40 dBm. The high efficiency and almost flatness in gain stability of proposed DPA providing better solution in order to overcome the interference and the broadband issues for LTE communication cells. The balun-filtered network is employed for combined the two outputs of carrier and peak amplifiers that provides more uniform desired band of operation in the frequency responses. The proposed DPA circuit are implemented and optimized by using advanced design RF simulator platform. The fabricated chip is made by using 0.13 ?m GaN HEMT on Si-Nitride monolithic microwave integrated circuit die process. The fabricated chip of DPA provides 85% of PAE with 28 dB gain which are made close agreement with simulation results. The size of chip is 2.8*1.2mm2 which occupies less die area as compared to existing DPAs. © 2018 Wiley Periodicals, Inc.Item An integrated cascode DE power amplifier for RF calibration system towards measurement of bio-sensor applications(John Wiley and Sons Inc. P.O.Box 18667 Newark NJ 07191-8667, 2019) Kumar, R.; Kumar Kanaujia, B.K.; Dwari, S.; Kumar, S.; Song, H.The integrated cascode DE power amplifier for RF calibration system toward measurement of bio-sensor applications is presented in this paper. The proposed architecture includes cascode class-D and class-E amplifier stages that could provide better calibration accuracy in terms of wide bandwidth, power efficiency, high gain, minimum group delay, and lowest calibration system. The achieved high performance of proposed amplifier overcomes conventional measurement issues toward bio-sensor application. The inductive ?-shape matching network drives RF input to class-D stage and provides wide bandwidth of operation. While class-E stage with T-shape matching network maintains stable gain and high efficiency in desired band of operation. The performance of the CMOS proposed amplifier is executed in RF ADS simulator along with fabricated chip using commercial TSMC 65 nm manufacturing process. The simulated and measured data achieves Ku band (12 GHz to 18 GHz) with almost flat gain of 30 dB. The DE amplifier provides an output and saturated power of 17 dBm with highest power efficiency of 45%. The measured calibration factor at maximum resonant frequency of 13.5 GHz achieves best value of less than 2 dB within input power range of ?50 dBm to 0 dBm. The lowest calibration factor provides best accuracy along with the other parameters and could be beneficial toward bio-sensor measurement in the various applications. The calculated area of the fabricated chip is as 0.45*0.45mm2 where class-E consuming area of 38% and class-D of 44%. The fabricated chip consumes less power consumption of 3.2 mW under power supply of 1 V. © 2018 Wiley Periodicals, Inc.Item Investigation of CMOS Based Integration Approach Using DAI Technique for Next Generation Wireless Networks(Springer New York LLC barbara.b.bertram@gsk.com, 2019) Roy, G.M.; Kanuajia, B.K.; Dwari, S.; Kumar, S.; Song, H.This research work investigates a CMOS based low noise amplifier (LNA) using differential active inductor with eight-shaped patch antenna for next generation wireless communication. The proposed work conceded into three different phases. The first phase proposes LNA architecture which includes multistage cascode amplifier with a gate inductor gain peaking technique. The ground approach for this architecture employs active inductor technique that includes two stages of differential amplifier. The proposed novel technique leads to give incremental in inductance by using of common mode feedback resistor and lowers the undesirable parasitic resistance effect. Additionally, this technique offers gain enhanced noise cancellation and achieves a frequency band of around 5.7 GHz. The proposed architecture includes single stage differential AI and enhances the bandwidth up to 6.8 GHz with peak gain of 21 dB at 7.8 GHz. The noise figure and stability factor are achieved which is reasonably good at 1 dB. The proposed architecture is design and optimized on advanced design RF simulator using 0.045 µm CMOS process technology. While in second phase, a narrow band eight-shaped patch antenna is designed which provides operating band range from 5.8 to 6.5 GHz with 6.2 GHz resonating frequency. Highest peak gain of 15 dB and maximum radiation power of 42.5 dBm is succeed by proposed antenna. The final phase provides integration strategy of LNA with antenna and achieves desired gain of nearly 21 dB with minimum NF of 1.2–1.5 dB in the same band. © 2018, Springer Science+Business Media, LLC, part of Springer Nature.Item Performance of cascode Class-EF?1 PA with built-in techniques for UWB radar toward monitoring of patient actions(Institution of Engineering and Technology kvukmirovic@theiet.org, 2020) Kumar, R.; Dwari, S.; Kumar Kanaujia, B.K.; Kumar, S.; Song, H.This work proposes a performance of the cascode Class-EF?1 power amplifier (PA) for UWB radar transmitter. The cascode Class-E PA with built-in techniques overcomes the traditional mismatch and provides good performance of PA. Incurs the resonance and switching effect is observed in cascode Class-E PA that compensates for the parasitic effects and provides a wide-impedance range. While design-II includes negative capacitance and inverse Class-F, which achieves a redundant performance of wide bandwidth and power-added efficiency (PAE). Design-II achieves the redundant performance compared with design-I. Both design-I and design-II are implemented and analysed through simulation and experimental results using RF 65 nm Samsung Magnachip Hynix CMOS process. Design-I achieves a wide-impedance bandwidth ranging from 3 to 11.7 GHz with drain efficiency (DE) and maximum PAE of 80 and 73% at the output power of 26.4 dBm. The global efficiency (GE) and error vector magnitude (EVM) of 70 and 5.2% are also achieving for design-I. The redundant performance in design-II achieves wide bandwidth with operating frequency range of 2-13 GHz with maximum DE and PAE of 85 and 76%. For design-II, GE and EVM are investigated as 68 and 4.9% that could validate the accuracy and robustness of the UWB radar. © The Institution of Engineering and Technology 2019Item Performance of ultra-wide band DCBLNA with suspended strip line radiator for human breast cancer diagnosis medical imaging application(Institution of Engineering and Technology, 2020) Roy, G.M.; Kumar Kanaujia, B.K.; Dwari, S.; Kumar, S.; Song, H.This study presents the performance of differential cascode balun low noise amplifier (DCBLNA) with ultra-wideband (UWB) for human breast cancer diagnosis. The proposed DCBLNA design-I with bulky spiral inductors achieves insufficient bandwidth with large power consumption of 10.8 mW. To attain the proper UWB band of operation, suspended strip line (SSLIN) radiators have employed in the proposed design-I. The performance of SSLIN is evaluated in terms of line capacitance and characteristic impedance by optimising its width. It is observed that best 50 ?n-II. DCBLNA design-II using SSLIN have achieving a desired band of operation ranging from 1.5 to 15.7 GHz and best NF of 0.5 dB. The gain and phase imperfections are simulated to characterise balun networks. The smallest gain imperfection achieved is 0.1 dB at 10 GHz while the simulated phase imperfection turns out to be sufficiently good with 2.35° at 8 GHz. The proposed DCBLNA design-II is implemented and fabricated using RFCMOS 45 nm Taiwan Semiconductor Manufacturing Company (TSMC) process under commercial conditions. The highest figure of merit comes out to be 3.2 that ensures good accuracy of medical imaging for breast cancer diagnosis. © The Institution of Engineering and Technology 2020.Item Active feedback supported CMOS LNA blended with coplanar waveguide-fed antenna for Wi-Fi networks(John Wiley and Sons Inc, 2021) Roy, G.M.; Dwari, S.; Kumar Kanaujia, B.K.; Kumar, S.; Song, H.This study presents integration of complementary CMOS active feedback low noise amplifier with coplanar waveguide fed patch antenna for Wi-Fi networks. The LNA design-I, involves a cascode amplifier followed by active feedback common source amplifier offering wideband impedance matching with lowered parasitic losses. The inductor-less feedback mechanism is used to nullify noise effect with extended bandwidth in the range of 2.2 to 5.8 GHz and a peak forward gain of 22.5 dB. It is implemented on agilent's advance design system using 45 nm CMOS process. The noise figure (NF) is approximately 2 dB while the stability factors µ and µ prime are well above 1 dB with IIP3 of about 15 dBm. The chip area is 0.57 x 0.57 mm2 under dc power supply of 1V while power consumption of 0.8 mW. A CPW fed antenna design-II, achieves a wide band response similar to the bandwidth of LNA. The size of the fabricated antenna is calculated as 40 x 40 mm2. The peak gain is approximately 4.1 dBi at 3.9 GHz. The codesign-III, proposes a receiver achieving a much wider band of 1.6 to 6 GHz with a gain of 16.5 dB and NF of 2.59 dB at 2.06 GHz. The codesign improves the system integration by reducing overall chip area and offers saving in the effective cost. © 2021 The Authors. IET Microwaves, Antennas & Propagation published by John Wiley & Sons Ltd on behalf of The Institution of Engineering and Technology.Item A 8–12 GHz, 44.3 dBm RF output class FF?1 DPA using quad-mode coupled technique for new configurable front-end 5G transmitters(Springer, 2021) Kumar, R.; Dwari, S.; Kumar Kanaujia, B.K.; Kumar, S.; Song, H.This paper presents a high-efficiency Class FF - 1 DPA using the quad-mode coupled technique for new configurable front-end 5G transmitters. The proposed DPA consists of carrier PA, main PA, input–output matching network and hybrid power network (HPN). The HPN includes a quad-mode coupled technique which is four-section U-shaped transmission line. The HPN is used for even–odd mode impedance analysis to ensures the high-selectivity of output power and achieve a wideband response in the presence of harmonic control conditions. The optimum harmonic impedance is analyzed for the desired band to achieve high output power and efficiency. The DPA circuit is fabricated by using 0.25 µm GaN HEMT on silicon nitride monolithic microwave integrated circuit die process. At maximum output power level of 44.3 dBm, the delivered power-added efficiency (PAE) of 64.3–67.3% and drain efficiency (DE) of 71.7–73.7% at even–odd mode operation are achieved with a gain of 13.0–14.3 dB. For the output power level of 39.045 dBm corresponding to 9 dB output back-off (OBO), the drain efficiency lies between 55–62% with 73% fractional bandwidth. All the demonstrated transmission parameters are working in the band of 8–12 GHz. The size of the chip is 2.8 × 1.9 mm2 and it occupies less die area as compared to the existing DPAs. © 2021, The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature.