Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item Multi objective optimisation of thermally enhanced machining parameters of Inconel 718 using grey relational analysis(Inderscience Publishers, 2017) Ganta, V.; Kalichetty, K.S.; Dupadu, D.The present work investigates an experimental study of thermally enhanced machining of nickel-based superalloy Inconel 718 using uncoated tungsten carbide inserts. An inexpensive flame heating technique using an oxyacetylene flame is used as a heat source for thermal enhancement of workpiece. The effects of cutting parameters like cutting speed, feed rate, depth of cut and temperature of workpiece on the performance characteristics like surface roughness, tool wear and material removal rate were studied. A L27 orthogonal array with four parameters and three levels was adopted for experimental design. Multi response optimisation was done using grey relation analysis to simultaneously minimise surface roughness, tool wear and to maximise material removal rate. It was observed that at cutting speed at 85.21 m/min, feed rate at 0.048 m/min, depth of cut at 0.6 mm and workpiece temperature at 600°C were optimal cutting parameters. It is clearly shown that the above performance characteristics in thermally enhanced machining can be improved effectively through this approach. © © 2017 Inderscience Enterprises Ltd.Item Comparative evaluations of machining performance during turning of 17-4 PH stainless steel under cryogenic and wet machining conditions(Taylor and Francis Inc. 325 Chestnut St, Suite 800 Philadelphia PA 19106, 2018) Sivaiah, P.; Dupadu, D.Productivity in machining of 17-4 PH stainless steel is adversely affected by the premature failure of tool and poor surface finish as a consequence of high cutting temperatures. Conventional cutting fluids not only create environmental and health problems but also fail to overcome the high cutting temperatures during machining. Cryogenic cooling is an environmentally clean cooling technology for attractive management of machining zone temperatures. The present study investigates the effect of cryogenic liquid nitrogen (LN2 at ?196°C) on cutting temperatures, cutting forces (main cutting force, feed force), surface roughness, tool flank wear and chip morphology in turning of 17-4 PH stainless steel with AlTiN PVD-coated tungsten-coated carbide inserts and results were compared to wet machining. In overall, cryogenic machining reduces the cutting temperature, cutting forces, surface roughness and tool flank wear to a maximum of 73.4, 17.62, 44.29 and 55.55%, respectively. Improved chip breakability was found in cryogenic machining. © 2018 Taylor & Francis Group, LLC.Item Performance evaluation of mechanical micro-drilling, electrical discharge machining and laser beam machining on nimonic 80A alloy(National Institute of Science Communication and Information Resources (NISCAIR) ijact.editor@gmail.com Dr. K. S. Krishnan Marg (Near Pusa Gate) New Delhi 110-012, 2018) Sudhakar, S.; Kumar, P.; Srinivas, G.; Ravishankar, S.; Dupadu, D.; Barshilia, H.C.Micromachining techniques such as mechanical micro-drilling, electrical discharge machining (EDM) and laser beam machining (LBM) play an important role in the manufacturing of micro-devices used in mechanical, electronics, aerospace and medical applications. In this paper, an effort has been made to compare the performance of these micromachining techniques with regard to tool wear, burr formation and surface integrity. This is done by producing 20 micro-holes of approximately 800 ?m diameter on a rectangular block (90×30×3 mm3) of Nimonic 80A superalloy. TiAlN coated WC micro-drills, Cu electrodes and CO2 laser beam are used to produce these holes in conventional micro-drilling, EDM and LBM, respectively. The quality of the drilled hole (diameter, surface roughness and micro-burr formation), tool diameter analysis, taper angle and material removal rate (MRR) are compared and reported. A comprehensive analysis is also carried out on overcut, which leads to hole inaccuracy. Results show that mechanical micro-drilling produces better results in the above mentioned characteristics in comparison to LBM and EDM techniques. The relatively better performance of mechanical micro-drilling is attributed to the usage of TiAlN coating on WC tool. © 2018, National Institute of Science Communication and Information Resources (NISCAIR). All rights reserved.Item Influence of deep cryogenic treatment on performance of cemented carbide (WC-Co) inserts during dry end milling of maraging steel(Elsevier Ltd, 2019) Varghese, V.; Ramesh, M.R.; Dupadu, D.Cryogenic treatment has developed as a technique to improve the life of the cutting tool, especially tungsten carbide inserts. The present study investigates the effect of cryogenic treatment of cemented carbide (WC-Co) inserts at the different soaking period of 18 h (CT-18), 24 h (CT-24) and 32 h (CT-32) at a sub-zero temperature of ?196 °C. The soaking period plays a crucial role in improving the wear resistance of the cryogenically treated tools. It is vital to determine the critical soaking period for the cryogenic treatment of cemented carbides. The mechanical and metallurgical characterization of cryogenically treated cemented carbide insert is carried out to understand the changes in the microstructure, grain size, chemical composition, microhardness and electrical conductivity after cryogenic treatment. The end milling experiments on maraging steel under dry environment are carried out using cryogenically treated inserts at different holding time and untreated inserts (UT). The machining performance of treated and untreated inserts are compared with respect to tool wear, surface roughness and cutting forces. The results revealed that cryogenic treatment is effective in resisting tool wear even at high spindle speeds. The cryogenically treated inserts exhibited higher tool life, better surface finish and lower cutting forces during machining at different spindle speeds. The optimum soaking time for cryogenic treatment of WC-Co inserts is found to be 24 h (CT-24) beyond which there is no improvement in microhardness and wear resistance. © 2018Item Characterisation and performance evaluation of TiSiN &tiAlSiN coatings by RF magnetron sputtering deposition during end milling of maraging steel(Institute of Physics Publishing helen.craven@iop.org, 2019) Varghese, V.; Ramesh, M.R.; Dupadu, D.; Shaik, H.Monolayer nanostructured thin films of TiSiN & TiAlSiN were deposited on WC-Co milling inserts using RF magnetron sputtering for metal cutting. The alloy targets of TiSi (80/20 at%) & TiAlSi (34/56/10 at%) were used for the deposition in an Ar + N atmosphere. The deposition time and parameters are optimized to develop a uniform and homogenous coating. The mechanical and metallurgical properties are characterized to analyze the wear resistance of the coating. The machinability studies on MDN 250 maraging steel is carried out using TiSiN and TiAlSiN coated WC-Co inserts under dry and wet environment. The machining responses such as surface roughness, cutting force, tool wear and tool life are analyzed by varying spindle speed. The results showed that TiAlSiN coating had a higher wear resistance and machining performance compared to the TiSiN coating owing to the high hardness and plasticity index of the coating. © 2020 IOP Publishing Ltd.Item Investigation on the performance of AlCrN and AlTiN coated cemented carbide inserts during end milling of maraging steel under dry, wet and cryogenic environments(Elsevier Ltd, 2019) Varghese, V.; K, A.; Ramesh, M.R.; Dupadu, D.The present study investigates the machining performance of AlCrN and AlTiN coated cemented carbide inserts during end milling of MDN 250 maraging steel. The mechanical and metallurgical characterization is carried out to determine the properties of the PVD coatings developed. The end milling experiments under dry, wet and cryogenic environment is carried out using coated uncoated inserts (UC) at different spindle speeds to evaluate the machining performance in terms of tool life, surface roughness and cutting forces. The coated inserts showed higher tool life, better surface finish, and low cutting forces during machining at different spindle speeds. It is found that the AlCrN coating had a better wear resistance and machining performance in comparison with AlTiN coating. The cryogenic environment reduced the surface roughness & cutting force and improved the tool life of the cutting tool compared to conventional dry and wet environment. It is revealed that coated tools along with cryogenic cooling can be employed for high-speed machining applications. © 2019 The Society of Manufacturing EngineersItem Experimental investigation of cryogenic end milling on maraging steel using cryogenically treated tungsten carbide-cobalt inserts(Springer, 2019) Varghese, V.; Ramesh, M.R.; Dupadu, D.The cryogenic machining and cryogenic treatment have already emerged as the sustainable manufacturing process of the future generation. The cryogenic treatment improves the cutting tool life, but the high cutting temperature developed during high-speed machining reduces the effect of cryogenic treatment of cutting tool. This study investigates the possible improvements in cutting tool life by combining cryogenic cooling and cryogenic treatment. The authors believe that these two techniques can replace conventional machining approaches using dry and wet machining conditions using coated carbide tools. The tungsten carbide-cobalt inserts are cryogenically treated (CT) at a soaking temperature of ? 195.8 °C for a period of 24 h and are used to evaluate milling performance under dry, wet, and cryogenic cutting environments. The machining experiments are conducted on maraging steel MDN 250 using one factor at a time approach by varying spindle speed and keeping feed rate and depth of cut as constant. The cutting force, surface roughness, tool wear, and subsurface microhardness are some of the machining responses evaluated and compared with an untreated cutting tool (UT). The tool life improved up to 24% during cryogenic machining using CT tools at a spindle speed of 270 rpm. © 2019, Springer-Verlag London Ltd., part of Springer Nature.