Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Additive Manufacturing of Syntactic Foams: Part 2: Specimen Printing and Mechanical Property Characterization(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2018) Singh, A.K.; Saltonstall, B.; Patil, B.; Hoffmann, N.; Doddamani, M.; Gupta, N.High-density polyethylene (HDPE) and its fly ash cenosphere-filled syntactic foam filaments have been recently developed. These filaments are used for three-dimensional (3D) printing using a commercial printer. The developed syntactic foam filament (HDPE40) contains 40 wt.% cenospheres in the HDPE matrix. Printing parameters for HDPE and HDPE40 were optimized for use in widely available commercial printers, and specimens were three-dimensionally (3D) printed for tensile testing at strain rate of 10?3 s?1. Process optimization resulted in smooth operation of the 3D printer without nozzle clogging or cenosphere fracture during the printing process. Characterization results revealed that the tensile modulus values of 3D-printed HDPE and HDPE40 specimens were higher than those of injection-molded specimens, while the tensile strength was comparable, but the fracture strain and density were lower. © 2018, The Minerals, Metals & Materials Society.Item Additive Manufacturing of Syntactic Foams: Part 1: Development, Properties, and Recycling Potential of Filaments(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2018) Singh, A.K.; Patil, B.; Hoffmann, N.; Saltonstall, B.; Doddamani, M.; Gupta, N.This work focuses on developing filaments of high-density polyethylene (HDPE) and their hollow particle-filled syntactic foams for commercial three-dimensional (3D) printers based on fused filament fabrication technology. Hollow fly-ash cenospheres were blended by 40 wt.% in a HDPE matrix to produce syntactic foam (HDPE40) filaments. Further, the recycling potential was studied by pelletizing the filaments again to extrude twice (2×) and three times (3×). The filaments were tensile tested at 10?4 s?1, 10?3 s?1, and 10?2 s?1 strain rates. HDPE40 filaments show an increasing trend in modulus and strength with the strain rate. Higher density and modulus were noticed for 2× filaments compared to 1× filaments because of the crushing of some cenospheres in the extrusion cycle. However, 2× and 3× filament densities are nearly the same, showing potential for recycling them. The filaments show better properties than the same materials processed by conventional injection molding. Micro-CT scans show a uniform dispersion of cenospheres in all filaments. © 2018, The Minerals, Metals & Materials Society.Item Eco-friendly lightweight filament synthesis and mechanical characterization of additively manufactured closed cell foams(Elsevier Ltd, 2019) Patil, B.; Bharath Kumar, B.R.; Bontha, S.; Balla, V.K.; Powar, S.; Hemanth Kumar, V.H.; Suresha, S.N.; Doddamani, M.Environmentally pollutant fly ash cenospheres (hollow microballoons) are utilized with most widely consumed, relatively expensive high density polyethylene (HDPE) for developing lightweight eco-friendly filament for 3D printing of closed cell foams. Cenospheres (20, 40 and 60 by volume %) are blended with HDPE and subsequently extruded in filament to be used for 3D printing. Cenosphere/HDPE blends are studied for melt flow index (MFI) and rheological properties. MFI decreases with cenospheres addition. Complex viscosity, storage and loss modulus increase with filler loading. DSC results on the filament and printed samples reveal increasing crystallization temperature and decreasing crystallinity % with no appreciable change in peak melting temperature. Cooling rate variations exhibit crystallinity differences between the filament and the prints. CTE decreases with increasing cenosphere content resulting in lower thermal stresses and under diffusion of raster leading to non-warped prints. Micrography on freeze fractured filament and prints show cenospheres uniform distribution in HDPE. Intact cenospheres lower the foam density making it lightweight. Tensile tests are carried out on filaments and printed samples while flexural properties are investigated for 3D prints. Cenospheres addition resulted in improved tensile modulus and decreased filament strength. Tensile and flexural modulus of printed foams increases with filler content. Results are also compared with injection molded samples. Printed foams registered comparable tensile strength. Specific tensile modulus is noted to be increased with cenospheres loading implying weight saving potential of 3D printed foams. Property map reveals printed foams advantage over other fillers and HDPE composites synthesized through injection and compression molding. © 2019 Elsevier LtdItem Compressive behavior of fly ash based 3D printed syntactic foam composite(Elsevier B.V., 2019) Patil, B.; Bharath Kumar, B.R.; Doddamani, M.Syntactic foams are widely used in damage tolerance and low-density applications. In present work compressive behavior of 3D printed three-phase syntactic foams under quasi-static strain rates (0.001, 0.01 and 0.1 s?1) are investigated. Extruded filaments of High density polyethylene (HDPE) with environmentally pollutant fly ash cenospheres (0, 20, 40 and 60 vol%) are used for 3D printing. Micrography reveal that syntactic foam filament and 3D printed samples are three phase systems comprising matrix, cenosphere and porosity. Matrix porosity of about 7% makes these foams lightweight and suitable for buoyant applications. The compressive properties are extracted from the stress-strain plots. It is observed that modulus and specific modulus increases with strain rate and cenosphere content. Specific compressive strength increases with strain rate and decrease with cenosphere content. © 2019 Elsevier B.V.Item Mechanical behaviour of additively manufactured bioactive glass/high density polyethylene composites(Elsevier Ltd, 2020) Jeyachandran, P.; Bontha, S.; Bodhak, S.; Balla, V.K.; Kundu, B.; Doddamani, M.Bioactive glass (BAG) is a well-known biomaterial that can form a strong bond with hard and soft tissues and can also aid in bone regeneration. In this study, BAG is added to a polymer to induce bioactivity and to realize fused filament fabrication (FFF) based printing of polymer composites for potential orthopaedic implant applications. BAG (5, 10, and 20 wt%) is melt compounded with high density polyethylene (HDPE) and subsequently extruded into feedstock filament for FFF-printing. Tensile tests on developed filaments reveal that they are stiff enough to resist forces exerted during the printing process. Micrography of printed HDPE/BAG reveals perfect diffusion of raster interface indicating proper selection of printing parameters. Micrography of freeze fractured prints shows the homogeneous distribution and good dispersion of filler across the matrix. The tensile, flexural, and compressive modulus of FFF-printed HDPE/BAG parts increases with filler addition. BAG addition to the HDPE matrix enhances flexural and compressive strength. The tensile and flexural behaviour of FFF-prints is comparable to injection molded counterparts. Property maps exhibit the merits of present study over the existing literature pertaining to desired bone properties and polymer composites used in biomedical applications. It is envisioned that the development of HDPE/BAG composites for FFF-printing can lead to possible orthopaedic implants and scaffolds to mimic the bone properties in customised anatomical sites or injuries. © 2020 Elsevier LtdItem Effect of axial compression on dynamic response of concurrently printed sandwich(Elsevier Ltd, 2021) Bharath, H.S.; Waddar, S.; Bekinal, S.I.; Jeyaraj, J.; Doddamani, M.In this work, the sandwich is concurrently realized using high density polyethylene (HDPE) skins and syntactic foam core through three-dimensional printing (3DP). Syntactic foam core is printed using lightweight feedstock filaments having glass microballoons (GMBs) by 20–60 vol% embedded in HDPE. These lightweight filaments are used as feed material in FFF (fused filament fabrication) based three-dimensional printer. The concurrently printed sandwich is loaded axially in a compressive mode for investigating the influence of GMB loading on buckling and natural frequency. The experimental load–deflection data and modal analysis are utilized for estimating critical buckling load and natural frequencies, respectively, under axial compression. Increasing GMB content enhances load to buckle and frequency of the printed sandwiches. The natural frequency decrease with higher compressive loads. Furthermore, the fundamental natural frequency increases exponentially when these printed sandwiches are subjected to axial compression loads that are higher than the load required for critical buckling. The load–deflection data and frequency obtained experimentally are compared with numerical predictions deduced using finite element analysis (FEA), which are noted to match well. © 2020 Elsevier Ltd