Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Compressive and flexural properties of functionally graded fly ash cenosphere-epoxy resin syntactic foams(John Wiley and Sons Inc, 2015) Doddamani, M.; Kishore; Shunmugasamy, V.C.; Gupta, N.; Vijayakumar, H.B.The present study focuses on developing functionally graded syntactic foams (FGSFs) based on a layered co-curing technique. The FGSFs were characterized for compressive and flexural properties and compared with plain syntactic foams. The results showed that the specific compressive modulus was 3-67% higher in FGSFs compared to plain syntactic foams. FGSF exhibited 5-34% and 34-87% higher specific modulus and strength, respectively in flexural mode. The microscopic examinations of comparative responses of the filler and matrix to deformation suggest that the failure is dominated by the matrix. The gradient in the composition of syntactic foams helps in effectively distributing the stress throughout the microstructure and results in improved mechanical performance of syntactic foams. From the microscopy studies, it is evident that, the failure mechanism in the FGSF under flexural loading is governed by a crack that initiated on the tensile side of the specimen and propagated through the thickness to cause complete fracture. The microscopic observations further clearly demonstrate the existence of seamless interfaces between the layers and a clear difference in the cenosphere concentration across the interface, affirming the gradation in the prepared samples. The results show that appropriate compositions of FGSFs can be selected to develop materials with improved mechanical performance. © 2014 Society of Plastics Engineers.Item Dynamic behavior of concurrently printed functionally graded closed cell foams(Elsevier Ltd, 2021) Dileep, B.; Prakash, R.; Bharath, H.S.; Jeyaraj, J.; Doddamani, M.In this work, functionally graded foams (FGFs) of closed cell types are three-dimensionally printed (3DP) concurrently. These closed cell syntactic foams are manufactured by reinforcing 20, 40, and 60 vol% hollow glass microballoons (GMBs) in the high density polyethylene (HDPE) matrix and are investigated for their mechanical buckling and free vibration response. The critical buckling load (Pcr) of the FGFs are evaluated using the Double Tangent Method (DTM), Modified Budiansky Criteria (MBC), and Vibration Correlation Technique (VCT). It is observed that Pcr evaluated by all three methods are in good agreement. Among all FGFs, FGF-2 exhibited higher buckling strength with 22–26% higher than FGF-1 and FGF-3. Under no-load and uniaxial compressive loads, the first three natural frequency of FGFs and their corresponding damping factors are evaluated. At first mode, the natural frequency of FGFs decreases in the pre-buckling zone and started increasing in the post-buckling zone. Damping factor exhibited reverse trend compared to the trend shown by the natural frequencies. Among all FGFs, FGF-2 (20-40-60 GMB gradation) exhibited better natural frequency. Experimental results are compared with a finite element based simulation results. © 2021 Elsevier LtdItem Sound absorption and transmission loss characteristics of 3D printed bio-degradable material with graded spherical perforations(Elsevier Ltd, 2022) Sailesh, R.; Yuvaraj, L.; Doddamani, M.; Mailan Chinnapandi, L.B.M.; Jeyaraj, J.The influence of spherical bubble perforations and their grading on acoustic characteristics of a 3D printed bio-degradable material is investigated. Samples with spherical bubble perforations of different sizes are distributed either uniformly or graded across the specimen thickness. A sample having typical cylindrical perforations is also analyzed for comparative analysis. Sound absorption (SA) and sound transmission loss (STL) characteristics are estimated by the impedance tube method. The results reveal that the SA of all functionally graded (FG) perforations is higher at low frequencies. The SA and bandwidth are higher for a specimen with uniform, lower diameter bubbles at higher frequencies. The STL of FG perforations is highest among the specimens, and the difference increases significantly with frequency. The numerical and experimental results match a high degree of accuracy. FG perforations exhibited superior performance for both SA and STL. The proposed graded spherical porosity can be effectively utilized in soundproofing applications across building and transportation sectors. © 2021 Elsevier LtdItem Buckling and dynamic responses of 3D printed nanocomposites and their graded variants(Elsevier Ltd, 2023) Kumar, S.; Ramesh, M.R.; Jeyaraj, P.; Doddamani, M.The experimental and numerical investigations are carried out for buckling and vibration of 3D printed functionalized MWCNTs/HDPE based nanocomposite (NC) and their functionally graded nanocomposite (FGNC) variants. Pcr(critical buckling load) is computed through MBC (modified budiansky criteria) and DTM (double tangent method) techniques. It is observed that Pcr of the 3D printed NCs and FGNCs increases with the functionalized MWCNTs content. The Pcr values for the NCs (H0.5-H5) computed using DTM and MBC increased in the range of 16–79%, while for FGNC-1 (H0.5-H1-H3) and FGNC-2 (H1-H3-H5), the Pcr increased from 54 to 91% compared to HDPE. Further, it is observed that the natural frequency of the NCs and FGNCs increases with the functionalized MWCNTs loading while decreases with rise in compression. The natural frequency of the NCs (H0.5-H5) and FGNCs increased up to 41% than HDPE. The highest Pcr and the natural frequency is noted for H5 and FGNC-2 prints. The experimental and numerical results showed good agreement. © 2023 Elsevier LtdItem Buckling behavior of non-uniformly heated 3D printed plain and functionally graded nanocomposites(John Wiley and Sons Inc, 2023) Kumar, S.; Ramesh, M.R.; Jeyaraj, J.; Powar, S.; Doddamani, M.The functionalized multi-walled carbon nanotubes (MWCNTs) (0.5–5 wt.%) are compounded with high density polyethylene (HDPE), and, subsequently, used for extruding nanocomposite filaments to fabricate nanocomposites (NCs) and functionally graded nanocomposites (FGNCs) through 3D printing. The 3D printed NCs are investigated for coefficient of thermal expansion (CTE), and buckling under different non-uniform temperature distributions (case-1: left edge heating, case-2: centre heating, and case-3: left and right edge heating). A significant reduction in CTE is observed with MWCNT addition and gradation. The highest reduction in CTE is observed for H5 (5 wt.% of MWCNT in HDPE) NC and H1 ⟶ H3 ⟶ H5 (FGNC-2) among the NCs and the FGNCs. It is noted that Tcr (critical buckling temperature) is highest for case-3 and lowest for case-2. The highest deflection is noticed in case-2, while no significant difference is observed in case-1 and case-3 heating conditions. It is also observed that Tcr increases with gradation and MWCNTs addition. The H5 NC and FGNC-2 exhibited the highest Tcr among the NCs and FGNCs, respectively. The maximum deflection is noticed for HDPE, whereas the minimum deflection is noticed for FGNC-2 and H-5 NC among the tested samples. The results also revealed that Tcr is very sensitive to type of heating. © 2023 Society of Plastics Engineers.Item 3D printed functionally graded foams response under transverse load(Elsevier B.V., 2023) Bonthu, D.; Mahesh, V.; Powar, S.; Doddamani, M.The applications of 3D printing are rapidly increasing in aerospace and naval applications. Nonetheless, 3D printing (3DP) of graded foams exhibiting property variation along the thickness direction is yet to be explored. In the current work, the different volume fractions of hollow glass micro balloon (GMB) reinforced high-density polyethylene (HDPE) composite based graded foams are 3D printed using the fused deposition modelling (FDM) technique. The bonding between successive layers and porosity distribution of these graded configurations are studied using micro-CT scan. Further, the 3D Printed functionally graded foams (FGFs) are tested for flexural response, and results are compared with numerical values. The micro-CT results showed delamination absence between the layers. In neat HDPE layers, porosity is not evident, while minor porosity creeps in the layers having the highest GMB content. Experimental results of the flexural test showed that the graded sandwiches exhibited better strength than the graded core alone. Compared to neat HDPE, the modulus of FGF-2 (H20–H40–H60) increased by 33.83%, implying better mechanical stiffness. Among all the FGFs, FGF-2 exhibited a better specific modulus. A comparative study of experimental and numerical results showed a slight deviation due to neglecting the induced porosity. © 2023 The AuthorsItem Dynamic response of 3D printed functionally graded sandwich foams(Emerald Publishing, 2023) Bonthu, D.; Bharath, B.; Bekinal, S.I.; Jeyaraj, J.; Doddamani, M.Purpose: The purpose of this study was to introduce three-dimensional printing (3DP) of functionally graded sandwich foams (FGSFs). This work was continued by predicting the mechanical buckling and free vibration behavior of 3DP FGSFs using experimental and numerical analyses. Design/methodology/approach: Initially, hollow glass microballoon-reinforced high-density polyethylene-based polymer composite foams were developed, and these materials were extruded into their respective filaments. These filaments are used as feedstock materials in fused filament fabrication based 3DP for the development of FGSFs. Scanning electron microscopy analysis was performed on the freeze-dried samples to observe filler sustainability. Furthermore, the density, critical buckling load (Pcr), natural frequency (fn) and damping factor of FGSFs were evaluated. The critical buckling load (Pcr) of the FGSFs was estimated using the double-tangent method and modified Budiansky criteria. Findings: The density of FGSFs decreased with increasing filler percentage. The mechanical buckling load increased with the filler percentage. The natural frequency corresponding to the first mode of the FGSFs exhibited a decreasing trend with an increasing load in the pre-buckling regime and an increase in post-buckled zone, whereas the damping factor exhibited the opposite trend. Originality/value: The current research work is valuable for the area of 3D printing by developing the functionally graded foam based sandwich beams. Furthermore, it intended to present the buckling behavior of 3D printed FGSFs, variation of frequency and damping factor corresponding to first three modes with increase in load. © 2023, Emerald Publishing Limited.Item 3D printing of functionally graded nanocomposites: An investigation of microstructural, rheological, and mechanical behavior(John Wiley and Sons Inc, 2024) Kumar, S.; Rajath, S.; Shivakumar, N.D.; Ramesh, M.R.; Doddamani, M.Manufacturing functionally graded material through 3D printing is challenging owing to the deposition of different materials with different thermal properties in each layer, leading to a higher thermal gradient between deposited and depositing layers, resulting in improper bonding between them and, hence, reduced mechanical properties. This study focuses on 3D printing of functionalized multi-walled carbon nanotubes (MWCNTs)/high-density polyethylene (HDPE)-based lightweight functionally graded nanocomposites (FGNCs) and their investigation for microstructural, rheological, physical, and mechanical properties. Functionalized MWCNTs (0.5% → 5%) are initially compounded with widely utilized HDPE to develop nanocomposites (H0.5→H5 pellets) for extruding filaments for 3D printing. 3D-printed FGNC samples are investigated through scanning electron microscopy (SEM), rheology, density, tensile, and flexural tests. SEM and rheology confirm the homogeneous dispersion of the filler in HDPE and the processing parameters suitability in blending, extrusion, and 3D printing. Complex viscosity (η*), loss modulus (E″), and storage modulus (E′) of FGNCs increase, while the damping decreases with the MWCNTs rise in the graded layers. Density results revealed the highest weight saving potential (~12%) of FGNC-2 (H1–H3–H5), showing great weight saving potential. Tensile and flexural properties rise when the MWCNTs content rises in the graded layer. The FGNC-2 showed the highest tensile strength and moduli, 37.12% and 90.41% higher than HDPE. Flexural strength and moduli are also found to be the highest for FGNC-2, 28.57%, and 26.83% higher than HDPE. The highest specific moduli and strength are found for FGNC-2, 46.16% and 44.14% higher than HDPE, respectively. Experimental findings are found to be strongly in agreement with numerical findings. 3D-printed FGNC-2 demonstrated the best flexural and tensile characteristics with the lowest weight and hence can be used to make practical parts and structures that need variable stiffness. Highlights: FGNCs functionally graded n anocomposites are concurrently 3D printed. FGNC-2 exhibited the highest weight saving potential of 12%. FGNC-2 showed 90.41% and 37.12% enhanced tensile modulus and strength. FGNC-2 displayed 28.57% and 26.83% improved flexural strength and modulus. FGNCs exhibited better mechanical performance than the homogeneous NCs. © 2024 Society of Plastics Engineers.