Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
7 results
Search Results
Item Influence of microballoon wall thickness on dynamic mechanical analysis of closed cell foams(Institute of Physics Publishing helen.craven@iop.org, 2019) Doddamani, M.Thermoplastics are most commonly used in industrial and consumer products. The growing interest in making them lightweight is always a priority in industrial practices. Investigations on thermoplastic based closed cell foams wall thickness variations for dynamic mechanical analysis (DMA), and crystallinity are scarce. The present study investigates storage modulus, loss modulus, damping, and % crystallinity as a function of glass microballoon/high-density polyethylene (GMB/HDPE) foam wall thickness and volume fraction variations. Crystallinity percentage variation in HDPE and their foams are analyzed through DSC traces. GMBs are mixed with HDPE in plasticorder, and subsequently, GMB/HDPE composite blend is compression molded. Varying wall thickness (particle density variations) GMB particles across three different volume fractions (20, 40 and 60%) are prepared. Storage modulus, loss modulus, and damping are observed to be increasing with particle wall thickness and volume fraction as compared to HDPE matrix resin. Thick walled GMB particle with the highest GMB content registered enhanced storage modulus compared to thin walled ones at lower temperatures. DMA properties increase with increasing wall thickness. Damping is noted to be less sensitive than the storage and loss modulus. Crystallinity is observed to be decreasing with increasing wall thickness and GMB content. Higher crystalline phase contributes towards DMA properties at lower filler loadings while higher wall thickness plays a vital role at higher filler content. © 2020 IOP Publishing Ltd.Item Eco-friendly lightweight filament synthesis and mechanical characterization of additively manufactured closed cell foams(Elsevier Ltd, 2019) Patil, B.; Bharath Kumar, B.R.; Bontha, S.; Balla, V.K.; Powar, S.; Hemanth Kumar, V.H.; Suresha, S.N.; Doddamani, M.Environmentally pollutant fly ash cenospheres (hollow microballoons) are utilized with most widely consumed, relatively expensive high density polyethylene (HDPE) for developing lightweight eco-friendly filament for 3D printing of closed cell foams. Cenospheres (20, 40 and 60 by volume %) are blended with HDPE and subsequently extruded in filament to be used for 3D printing. Cenosphere/HDPE blends are studied for melt flow index (MFI) and rheological properties. MFI decreases with cenospheres addition. Complex viscosity, storage and loss modulus increase with filler loading. DSC results on the filament and printed samples reveal increasing crystallization temperature and decreasing crystallinity % with no appreciable change in peak melting temperature. Cooling rate variations exhibit crystallinity differences between the filament and the prints. CTE decreases with increasing cenosphere content resulting in lower thermal stresses and under diffusion of raster leading to non-warped prints. Micrography on freeze fractured filament and prints show cenospheres uniform distribution in HDPE. Intact cenospheres lower the foam density making it lightweight. Tensile tests are carried out on filaments and printed samples while flexural properties are investigated for 3D prints. Cenospheres addition resulted in improved tensile modulus and decreased filament strength. Tensile and flexural modulus of printed foams increases with filler content. Results are also compared with injection molded samples. Printed foams registered comparable tensile strength. Specific tensile modulus is noted to be increased with cenospheres loading implying weight saving potential of 3D printed foams. Property map reveals printed foams advantage over other fillers and HDPE composites synthesized through injection and compression molding. © 2019 Elsevier LtdItem Mechanical behavior of additively manufactured nanoclay/HDPE nanocomposites(Elsevier Ltd, 2020) Beesetty, P.; Kale, A.; Patil, B.; Doddamani, M.Nanoclay (NC) has blended with relatively inexpensive, widely consumed HDPE (high density polyethylene) for the development of filament to be used in 3D printers. NC/HDPE blends are prepared by varying NC wt. % (0.5, 1, 2, and 5) and are subjected to melt flow index (MFI) measurements. MFI has noted to be decreasing with NC loadings. NC/HDPE nanocomposite blends are further extruded using a single screw extruder. Developed nanocomposites filaments are fed to the fused filament fabrication (FFF) based 3D printer for realizing NC/HDPE nanocomposite prints. The density of printed sample increases with filler content. Filament and printed samples thermal study is carried out using differential scanning calorimeter (DSC). NC addition increases crystallinity and crystallization temperature without significant change in melting peak temperature. Freeze fractured prints reveal the uniform distribution of NC in HDPE. The tensile test is conducted on the filaments and prints. Further printed nanocomposites are subjected to flexural investigations. Tensile modulus and strength of filament increase with NC additions in HDPE matrix. Tensile and flexural properties (modulus and strength) of the nanocomposite prints increases with NC content. Finally, results obtained from the tensile and flexural tests of prints are compared with different HDPE composites available in the literature. © 2020 Elsevier LtdItem Material extrusion additive manufacturing of bioactive glass/high density polyethylene composites(Elsevier Ltd, 2021) Jeyachandran, P.; Bontha, S.; Bodhak, S.; Balla, V.K.; Doddamani, M.Bioactive glasses (BAG) are renowned for their unique ability to bond with tissues and therefore are used extensively for bone repair and functional recovery. In this work, high density polyethylene (HDPE) reinforced with BAG is processed using material extrusion additive manufacturing (MEAM) for potential orthopaedic applications. The constituents are melt compounded by varying BAG proportions (5, 10, and 20 wt %) and subsequently extruded into filaments. DSC curves show an insignificant change in the peak melting temperature, increase in crystallization temperature, and a decrease in the crystallinity of HDPE with BAG addition. Warpage analysis confirms that the enhanced temperature parameters and BAG addition result in reduced warpage and improved dimensional stability. Rheological results show that the addition of BAG increases complex viscosity, storage and loss modulus. Melt behavior and print parameters are tailored to improve first layer adhesion and interfacial bonding rendering dimensionally stable prints without any print induced defects. Dynamic mechanical analysis (DMA) of printed samples show an increase in storage (E?), loss (E?) modulus, and a decrease in damping factor (Tan ?) with BAG addition. MEAM of the developed H/BAG composites shows a strong potential for developing customizable scaffolds and implants as bone replacements. © 2021 Elsevier LtdItem Recycling potential of MWCNTs/HDPE nanocomposite filament: 3D printing and mechanical characterization(Springer, 2023) Kumar, S.; Ramesh, M.R.; Doddamani, M.Fused filament fabrication (FFF) based additive manufacturing (AM) process is a widely used and emerging manufacturing process for polymer-based products. The recycled filaments are realized through wastage generated while extruding the constant diameter feedstock filament, which is otherwise dumped in landfills or incinerated, releasing hazardous and toxic gases that influence the ecological environment. The wastage of these filaments can be eliminated by recycling and reusing them, addressing materials circular economy effectively, presented in this paper. The functionalized MWCNT reinforced HDPE (high-density polyethylene) nanocomposite (NC) is realized through a brabender, which is further used for filament extrusion. The waste/unrecycled (W/UR) and the recycled filaments are checked for quality. The density of the recycled filaments increases compared to the W/UR filament in each extrusion pass. The crystallinity and tensile properties of the recycled filaments increase compared to the W/UR filament with each additional extrusion cycle. Further, these filaments are used for 3D printing, and investigated for density, XRD and tensile tests. It is observed that the density, crystallinity and tensile properties of the recycled prints increase compared to the W/UR print. The tensile strength and modulus of 1 × , 2 × and 3 × prints are 63.82, 67.11 and 67.76%, and 45.63, 55.34 and 97.81% respectively, higher than those of the W/UR print. The highest tensile strength and modulus are observed for 3 × print which is 67.76 and 97.81% respectively, higher than those of the W/UR print. 3D prints exhibited enhanced performance as compared to their respective filaments. Finally, the present tensile results are mapped on a property chart, and compared with the available HDPE composites. © 2023, Springer Nature Japan KK, part of Springer Nature.Item A comprehensive characterization of 3D printable poly ether ketone ketone(Elsevier Ltd, 2024) Ojha, N.; Kumar, S.; Ramesh, M.R.; Balan, A.A.S.; Doddamani, M.The current work focuses on the comprehensive characterization of a 3D printable biomaterial, polyether ketone ketone (PEKK). The PEKK granules are first characterized and then utilized for extrusion of the PEKK filaments. The extruded PEKK filaments are characterized for crystallinity, quality, and printability, wherein they exhibit amorphous nature, good quality, and appropriate printability. Utilizing the filaments, the samples are printed with the appropriate printing parameters, which are further characterized for layer adhesion, voids, and crystallinity, wherein they showed seamless layer adhesion, improper beads consolidation, and the amorphous nature. The as printed samples are further annealed at different temperatures (200 and 250 °C). The scanning electron microscopy (SEM) of the annealed samples (A-200 and A-250) revealed better void consolidation, while the X-ray diffraction (XRD) revealed better crystallinity compared to the un-annealed sample. The printed samples are also investigated for dynamic mechanical analysis (DMA), shape memory, and tensile properties. The storage moduli of the annealed samples are observed to be better than the un-annealed sample. The annealed samples exhibited better shape memory properties: shape fixity and shape recovery ratio of A-200 and A-250 samples, 90.28 and 90.75%, and 99.16 and 94.73%, respectively, compared to the un-annealed samples. The highest shape fixity ratio and the shape recovery ratio are noted for A-250 (90.75%) and A-200 (∼ 100%). The A-200 and A-250 samples showed enhanced tensile modulus and strength, 4.16 and 49.67%, and 36.61 and 35.06%, respectively compared to the un-annealed sample. The highest modulus is noted for A-250, while the strength is comparable (36.61 and 35.06%) for A-200 and A-250. © 2023 Elsevier LtdItem Green synthesis of fe/ni/cr oxide nanoparticles using costus pictus plant extract: Microstructure and biological properties(World Scientific, 2024) Kumar, P.; Ramesh, M.R.; Doddamani, M.; Suresh, J.Superior qualities to bulk material and larger surface area to volume ratio are some of the primary reasons that account for the wide use of nanoparticles (NPs) in biological applications. Advancements in molecular-level engineering and environmental and health concerns are driving factors in the green synthesis of NPs. Plant-based NP synthesis provides a good alternative compared to hazardous physical and chemical techniques of synthesis of NPs. An experimental study is carried out on the green synthesis of Fe/Ni/Cr oxide NPs using Costus pictus extract. The study encompassed an array of characterization techniques, including UV-visible spectroscopy for absorption properties, X-ray diffraction (XRD) for crystallinity assessment, and Fourier-transform infrared (FTIR) spectroscopy to probe the presence of phenolic groups in flavonoids that influence NP formation. Surface morphology and composition were elucidated using scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), while transmission electron microscopy (TEM) affirmed the NPs' size (approximately 20 nm). The surface area of the NPs, 96.806 m2/g, was determined through BET analysis. Furthermore, the antibacterial potential of the NPs against various bacterial strains, including S. mutans, E. coli, P. aeruginosa, and S. aureus, was investigated using the agar well diffusion method. The NPs showed good antibacterial potential against bacterial species E. coli and P. aeruginosa. © 2024 World Scientific Publishing Company.