Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
14 results
Search Results
Item Dry sliding wear of epoxy/cenosphere syntactic foams(Elsevier Ltd, 2015) Manakari, V.; Parande, G.; Doddamani, M.; Gaitonde, V.N.; Siddhalingeshwar, I.G.; Kishore; Shunmugasamy, V.C.; Gupta, N.Abstract Dry sliding wear behavior of epoxy matrix syntactic foams filled with 20, 40 and 60 wt% fly ash cenosphere is reported based on response surface methodology. Empirical models are constructed and validated based on analysis of variance. Results show that syntactic foams have higher wear resistance than the matrix resin. Among the parameters studied, the applied normal load (F) had a prominent effect on wear rate, specific wear rate (ws) and coefficient of friction (?). With increasing F, the wear rate increased, whereas ws and ? decreased. With increase in filler content, the wear rate and ws decreased, while the ? increased. With increase in sliding velocity as well as sliding distance, the wear rate and ws show decreasing trends. Microscopy revealed broken cenospheres forming debris and extensive deformation marks on the wear surface. © 2015 Elsevier Ltd.Item High temperature erosion behavior of plasma sprayed NiCrAlY/WC-Co/cenosphere coating(Elsevier B.V., 2017) Mathapati, M.; Ramesh, M.R.; Doddamani, M.High temperature erosive behavior of plasma sprayed NiCrAlY-25WC-Co/cenosphere coating deposited on MDN 321 steel is investigated in the present work. Coating is characterized using Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD). Microhardness, porosity, adhesion strength, fracture toughness and ductility of the coating are quantified. Solid particle erosion test is conducted at 200, 400 and 600 °C with 30 and 90° impact angles using alumina erodent. Optical profilometer is used to evaluate erosion volume loss. Erosion resistance of the coating is observed to be higher than the substrate for the test temperatures chosen and noted to be more prominent at lower impact angle and higher temperature. High temperature stability of mullite, alumina and oxide layer assists in increasing erosion resistance of coating. The eroded coating surface morphology reveals the brittle mode of material removal. © 2017 Elsevier B.V.Item Compressive behavior of cenosphere/epoxy syntactic foams in arctic conditions(Elsevier Ltd, 2018) Shahapurkar, K.; Garcia, C.D.; Doddamani, M.; Mohan Kumar, G.C.; Prabhakar, P.In this paper, the effects of arctic condition on the compressive response of ceno-sphere/epoxy syntactic foams are investigated. Understanding the behavior of such foams under extreme conditions is critical for exploring their suitability for constructing lightweight platforms used in arctic explorations, which are exposed to subzero temperatures for extended periods of time potentially degrading their mechanical properties. In the research study presented here, samples of cenosphere/epoxy syntactic foams were conditioned under arctic environment at a temperature of ?60 °C for a period of 57 days. Compression tests were then conducted at room temperature as well as in-situ ?60 °C on the conditioned samples and compared against unconditioned samples tested at room temperature. Combinations of surface modification and cenosphere volume fractions were considered. For the case of unconditioned samples, compressive strength decreased with increasing cenosphere volume fraction for both surface modified and unmodified cenospheres. For the arctic conditioned samples, cenospheres/epoxy foams did not present visible signs of degradation prior to testing, but manifested a reduction in compressive modulus in a range of 47–57% and 47–65% for untreated and treated cenospheres/epoxy syntactic foams as compared to their unconditioned counterparts. On the other hand, the compressive strength increased in a range between 32–68% for untreated and 59–80% for treated cenosphere foams in arctic environment, which can be attributed to the matrix hardening introduced by frigid in-situ environment. Also, under in-situ arctic compressive loading, the post peak response for all foam types have shifted from a progressive failure to a brittle type behavior. © 2017 Elsevier LtdItem High-Temperature Erosive Behavior of Plasma Sprayed Cr3C2-NiCr/Cenosphere Coating(Springer New York LLC barbara.b.bertram@gsk.com, 2018) Mathapati, M.; Doddamani, M.; Ramesh, M.R.This research examines the deposition of Cr3C2-NiCr/cenosphere and Cr3C2-NiCr coatings on MDN 321 steel through the process of plasma spray. In this process, the solid particle erosion test is established at 200, 400, 600 °C with 30° and 90° impact angles. Alumina erodent is adopted to investigate the erosive behavior of the coating at higher temperatures. The properties of the Cr3C2-NiCr/cenosphere coating are established based on the microhardness, the adhesive strength, the fracture toughness, and the ductility. To quantify volume loss as a result of erosion, an optical profilometer is used. At higher temperature, decrease in the erosion volume loss of Cr3C2-NiCr/cenosphere and Cr3C2-NiCr coatings is observed. The erosion-resistive property of Cr3C2-NiCr/cenosphere coating is higher than that of MDN 321 steel by 76%. This property is influenced by high-temperature stability of mullite, alumina, and protective oxide layer that is formed at elevated temperatures. The morphology of eroded coating discloses a brittle mode of material removal. © 2018, ASM International.Item Effect of arctic environment on flexural behavior of fly ash cenosphere reinforced epoxy syntactic foams(Elsevier Ltd, 2018) Garcia, C.D.; Shahapurkar, K.; Doddamani, M.; Mohan Kumar, G.C.M.; Prabhakar, P.In this paper, the effect of arctic conditions on the flexural response of cenosphere/epoxy syntactic foams is investigated. Understanding the behavior of such foams under extreme conditions is critical for exploring their suitability for constructing lightweight platforms used in arctic explorations. Such platforms are exposed to subzero temperatures for extended periods of time potentially degrading their mechanical properties. In the research study presented here, samples of cenosphere/epoxy syntactic foams were conditioned under arctic environment at ?60 °C temperature for a period of 57 days. Flexural tests were then conducted at room temperature as well as in-situ ?60 °C on the conditioned samples and compared against unconditioned samples. Combinations of surface modification and cenosphere volume fractions were considered. Experimental findings showed that an increase in flexural modulus can be observed at room temperature with increasing cenosphere volume content for both untreated and treated cenosphere reinforced syntactic foams. In contrast, a decrease in flexural strength was observed as compared to neat resin. For the case of arctic exposed samples, an apparent increase in flexural modulus was recorded between 7-15% as compared to room temperature cenospheres/epoxy syntactic foams. In addition, an apparent increase of 3–80% in the flexural strength was observed under arctic environment. The conditioning of cenosphere/epoxy syntactic foams under low temperatures manifested lower strains to failure as compared to neat epoxy and they exhibit quasi-brittle behavior leading to sudden failure in the post peak regime. © 2018 Elsevier LtdItem Influence of surface modification on wear behavior of fly ash cenosphere/epoxy syntactic foam(Elsevier Ltd, 2018) Shahapurkar, K.; Chavan, V.B.; Doddamani, M.; Mohan Kumar, G.C.M.The present study deals with investigating the surface modification effect of fly ash cenosphere (as received and surface treated) on the friction and wear response of epoxy syntactic foams. Such lightweight syntactic foams have the potential in using them as tribo-materials for friction applications like in brake pad composites. This study also addresses the environmental linked disposal issues of fly ash cenospheres by incorporating them (up to 60 vol%) in the epoxy matrix. Cenosphere content and surface modification influence on the friction and wear response of cenosphere/epoxy syntactic foams is investigated against EN31 steel disc under dry sliding conditions. Wear behavior is studied at room temperature for different velocities (2 and 5 m/s), applied loads (30 and 50 N) and sliding distances (3, 5 and 7 km). Neat epoxy exhibits maximum wear rate as compared to foams. Wear rate decreases with increasing sliding distance and cenosphere content at all tested conditions. With the increase in the applied load and the sliding velocity, higher wear rate is noted for neat epoxy samples while it decreases with increasing filler loading. Surface modified cenosphere reinforced foams exhibit better wear resistance compared to as received cenosphere dispersed foams and neat epoxy for all the operating conditions owing to the good interfacial bonding of treated cenospheres with epoxy matrix. Specific wear rate decreases significantly with an increase in applied load. Further, the coefficient of friction decreases with higher filler loading and surface modifications. Scanning electron microscopy is used to study the wear mechanisms. Wear debris is analyzed and disc temperature is also reported. Finally, wear rate results are summarised and compared with the data available from literature and are presented in a property map. © 2018 Elsevier B.V.Item Microstructure and tribological behavior of plasma sprayed NiCrAlY/WC-Co/cenosphere/solid lubricants composite coatings(Elsevier B.V., 2018) Doddamani, M.; Mathapati, M.; Ramesh, M.R.Present investigation deal with NiCrAlY/WC-Co/Cenosphere/MoS2/CaF2, NiCrAlY/WC-Co/Cenosphere/MoS2/CaSO4 and NiCrAlY/WC-Co/Cenosphere coatings deposited on MDN 321 steel using atmospheric plasma spraying. Tribological properties of MDN 321 steel and coatings are evaluated from room temperature (RT) to 600 °C under dry lubrication conditions using a pin on disc high-temperature tribometer. Scanning Electron Microscopy (SEM), X-ray diffraction (XRD) and Energy Dispersive Spectroscopy (EDS) are used to characterize the coatings. Presence of cenospheres in these coatings might effectively reduce wear acting as localized regions accumulating wear debris. The result shows that wear rate of all the coatings are lower as compared to MDN 321 substrate at all the test conditions. NiCrAlY/WC-Co/Cenosphere/MoS2/CaF2 and NiCrAlY/WC-Co/Cenosphere/MoS/CaSO4 coatings registered lower friction coefficient as compared to NiCrAlY/WC-Co/Cenosphere coating and MDN 321 substrate. Characterization of the NiCrAlY/WC-Co/Cenosphere/MoS2/CaF2 and NiCrAlY/WC-Co/Cenosphere/MoS2/CaSO4 coatings worn out surface suggests that MoS2 provides lubrication at 200 °C and formation of CaMoO4, MoO3 through tribo chemistry reaction at higher temperature provides lubrication at 600 °C. SEM micrograph of worn surface demonstrates that the main wear mechanism is plowing and delamination. © 2018 Elsevier B.V.Item Plasma sprayed Cr3C2-NiCr/fly ash cenosphere coating: Cyclic oxidation behavior at elevated temperature(Institute of Physics Publishing helen.craven@iop.org, 2018) Doddamani, M.; Mathapati, M.; Ramesh, M.R.Oxidation is one of the major degradation phenomena observed in components subjected to higher temperatures like in thermal power plants (boiler tubes), steam and gas turbines blades etc. Developing protective coatings for such components mitigate oxidation. In the present study, plasma spray technique is utilized to deposit the Cr3C2-NiCr/Cenospheres coating on MDN 321 steel substrate. Thermo cyclic oxidation test is conducted at 600 °C (20 cycles) on both the coating and MDN 321 steel substrate. The thermogravimetric methodology is employed to estimate the oxidation kinetics. Energy Dispersive Spectroscopy (EDS), x-ray Diffraction (XRD), Scanning Electron Microscope (SEM) and x-ray mapping technique is employed to characterize the oxidized samples. Cr3C2-NiCr/Cenosphere coating displayed lower rate of oxidation as compared to substrate implying its suitability in high-temperature applications. Protective oxides like Al2O3, Cr2O3, and NiCr2O4 are observed on the uppermost layer of the coating lowering the oxidation rate in the developed coating. © 2018 IOP Publishing Ltd.Item Effect of surface treatment on quasi-static compression and dynamic mechanical analysis of syntactic foams(Elsevier Ltd, 2019) Doddamani, M.Quasi static compression (10 ?1 , 10 ?2 and 10 ?3 s ?1 strain rates) and dynamic mechanical analysis (temperature sweep of 30–175 °C) of cenosphere/epoxy syntactic foams are investigated. Effect of cenosphere content (20, 40 and 60 vol %) and surface modification are presented. Quasi-static tests reveal lower modulus for neat epoxy samples as compared to all the syntactic foams. With increasing cenosphere content and strain rate, elastic modulus increases for all the tested conditions. Foams reinforced with surface modified cenosphere exhibit higher modulus as compared with untreated ones and neat epoxy. Energy absorption of samples increases with increasing cenosphere content and surface modification. Storage modulus of untreated and treated syntactic foams register higher values with increase in cenosphere content and are higher than the neat epoxy samples. Loss modulus of syntactic foams at room temperature are lower as compared with pure epoxy while damping of untreated and treated foams registered higher values as compared with neat resin. Scanning electron microscopy of the samples are performed for structure property correlations. Finally, property map for quasi-static compression is presented by comparing results of present work with the extracted values from literature. © 2019 Elsevier LtdItem Eco-friendly lightweight filament synthesis and mechanical characterization of additively manufactured closed cell foams(Elsevier Ltd, 2019) Patil, B.; Bharath Kumar, B.R.; Bontha, S.; Balla, V.K.; Powar, S.; Hemanth Kumar, V.H.; Suresha, S.N.; Doddamani, M.Environmentally pollutant fly ash cenospheres (hollow microballoons) are utilized with most widely consumed, relatively expensive high density polyethylene (HDPE) for developing lightweight eco-friendly filament for 3D printing of closed cell foams. Cenospheres (20, 40 and 60 by volume %) are blended with HDPE and subsequently extruded in filament to be used for 3D printing. Cenosphere/HDPE blends are studied for melt flow index (MFI) and rheological properties. MFI decreases with cenospheres addition. Complex viscosity, storage and loss modulus increase with filler loading. DSC results on the filament and printed samples reveal increasing crystallization temperature and decreasing crystallinity % with no appreciable change in peak melting temperature. Cooling rate variations exhibit crystallinity differences between the filament and the prints. CTE decreases with increasing cenosphere content resulting in lower thermal stresses and under diffusion of raster leading to non-warped prints. Micrography on freeze fractured filament and prints show cenospheres uniform distribution in HDPE. Intact cenospheres lower the foam density making it lightweight. Tensile tests are carried out on filaments and printed samples while flexural properties are investigated for 3D prints. Cenospheres addition resulted in improved tensile modulus and decreased filament strength. Tensile and flexural modulus of printed foams increases with filler content. Results are also compared with injection molded samples. Printed foams registered comparable tensile strength. Specific tensile modulus is noted to be increased with cenospheres loading implying weight saving potential of 3D printed foams. Property map reveals printed foams advantage over other fillers and HDPE composites synthesized through injection and compression molding. © 2019 Elsevier Ltd