Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Development of glass microballoon/HDPE syntactic foams by compression molding(Elsevier Ltd, 2017) Jayavardhan, M.L.; Bharath Kumar, B.R.; Doddamani, M.; Singh, A.K.; Zeltmann, S.E.; Gupta, N.Thermoplastic resins are widely used in consumer products and industrial components. There is a significant interest in weight reduction of many of those components. Although glass hollow particle filled lightweight syntactic foams with thermoset matrices have been studied in detail, studies on thermoplastic syntactic foams are scarce. The present study is focused on developing a compression molding based processing method for glass microballoon/high density polyethylene (GMB/HDPE) syntactic foams and studying their mechanical properties to develop structure-property correlations. Blending of GMB in HDPE is carried out using a Brabender mixer with processing parameters optimized for minimal filler breakage. Flexural and tensile test specimens are compression molded with 20, 40 and 60 vol% of GMB. Particle fracture increases with increasing GMB content due to increased particle to particle interaction during processing. Additionally, increasing wall thickness makes GMBs stronger and results in reduced particle fracture. Flexural modulus increases while strength decreases with increasing filler content. Tensile strength decreases with increasing filler content, while tensile modulus is relatively unchanged. GMB volume fraction has a more prominent effect than the wall thickness on the mechanical properties of syntactic foams. Specific moduli of GMB/HDPE foams are superior while specific strength is comparable to neat HDPE. © 2017 Elsevier LtdItem 3D printing of functionally graded nanocomposites: An investigation of microstructural, rheological, and mechanical behavior(John Wiley and Sons Inc, 2024) Kumar, S.; Rajath, S.; Shivakumar, N.D.; Ramesh, M.R.; Doddamani, M.Manufacturing functionally graded material through 3D printing is challenging owing to the deposition of different materials with different thermal properties in each layer, leading to a higher thermal gradient between deposited and depositing layers, resulting in improper bonding between them and, hence, reduced mechanical properties. This study focuses on 3D printing of functionalized multi-walled carbon nanotubes (MWCNTs)/high-density polyethylene (HDPE)-based lightweight functionally graded nanocomposites (FGNCs) and their investigation for microstructural, rheological, physical, and mechanical properties. Functionalized MWCNTs (0.5% → 5%) are initially compounded with widely utilized HDPE to develop nanocomposites (H0.5→H5 pellets) for extruding filaments for 3D printing. 3D-printed FGNC samples are investigated through scanning electron microscopy (SEM), rheology, density, tensile, and flexural tests. SEM and rheology confirm the homogeneous dispersion of the filler in HDPE and the processing parameters suitability in blending, extrusion, and 3D printing. Complex viscosity (η*), loss modulus (E″), and storage modulus (E′) of FGNCs increase, while the damping decreases with the MWCNTs rise in the graded layers. Density results revealed the highest weight saving potential (~12%) of FGNC-2 (H1–H3–H5), showing great weight saving potential. Tensile and flexural properties rise when the MWCNTs content rises in the graded layer. The FGNC-2 showed the highest tensile strength and moduli, 37.12% and 90.41% higher than HDPE. Flexural strength and moduli are also found to be the highest for FGNC-2, 28.57%, and 26.83% higher than HDPE. The highest specific moduli and strength are found for FGNC-2, 46.16% and 44.14% higher than HDPE, respectively. Experimental findings are found to be strongly in agreement with numerical findings. 3D-printed FGNC-2 demonstrated the best flexural and tensile characteristics with the lowest weight and hence can be used to make practical parts and structures that need variable stiffness. Highlights: FGNCs functionally graded n anocomposites are concurrently 3D printed. FGNC-2 exhibited the highest weight saving potential of 12%. FGNC-2 showed 90.41% and 37.12% enhanced tensile modulus and strength. FGNC-2 displayed 28.57% and 26.83% improved flexural strength and modulus. FGNCs exhibited better mechanical performance than the homogeneous NCs. © 2024 Society of Plastics Engineers.Item 4D printing of heat-stimulated shape memory polymer composite for high-temperature smart structures/actuators applications(John Wiley and Sons Inc, 2024) Kumar, S.; Ojha, N.; Ramesh, M.R.; Doddamani, M.High temperature shape memory polymers (HT-SMPs) have great utilization in self-deployable hinges/morphing structures for space/aerospace, and high-temperature sensors/actuators for electronics. However, HT-SMPs have many drawbacks, such as low stiffness, strength, thermal stability, and dynamic mechanical properties. This work aims at improving these properties of highly utilized space grade HT-SMP, PEKK (polyether ketone ketone), by reinforcing it with low-cost carbon fibers (CFs), and developing its composite via additive manufacturing. The additively manufactured CF/PEKK composites are annealed at 200 °C (CF/PEKK-A200) and 250 °C (CF/PEKK-A250), and for the first time, investigated for shape memory effect (SME). The shape fixity and the shape recovery of the CF/PEKK-UNA (un-annealed), CF/PEKK-A200, and CF/PEKK-A250 are noted to be 95.97%, 88.95%, and 86.40%, and 88.70%, 92.70%, and 95.19%, respectively with a significant weight saving potential of ?21%. Dispersion of CFs in PEKK and suitability of processing parameters (blending, extrusion, and 3D printing) are confirmed through scanning electron microscopy (SEM). Thermal degradation temperature ((Formula presented.)) of the printed CF/PEKK composite (?568 °C) is found to be ?3.5% higher than PEKK (?549 °C). CF/PEKK-A250 exhibited the highest storage modulus (4438.23 MPa), ~158% higher than PEKK (1722.3 MPa), while CF/PEKK-A200 demonstrated the highest tensile modulus (10.9 GPa), which is 138.5% higher than PEKK (4.57 GPa) and 312.88% higher than CF/PEKK-UNA (2.64 GPa). Moreover, CF/PEKK-A200 exhibited 237.46%, 138.51%, 127.08%, 61.48%, 32.93%, and 50.35% higher tensile modulus than PEEK, PEKK, PEK, CF/PEK, CF/PEEK, and CF/PEKK composites, respectively, showing great potential to replace them. Highlights: Printed CF/PEKK composites are investigated for shape memory behavior. The printed composites exhibited outstanding shape memory properties. Printed-A200 exhibited 138.51% enhanced tensile modulus than pure PEKK. Also, the printed-A200 showed 313% enhanced modulus than printed-UNA. (Formula presented.) (568 °C) of the printed composites is found ?4% greater than pure PEKK. © 2024 Society of Plastics Engineers.Item A short banana fiber—PLA filament for 3D printing: Development and characterization(John Wiley and Sons Inc, 2025) Mohamed Shafeer, P.P.; Pitchaimani, J.; Doddamani, M.This study aims to develop a 3D printable composite filament using short banana fiber and polylactic acid (PLA). The filament was acquired through a single screw extruder, employing various blending techniques. Various fiber loadings were examined, impacting PLA's mechanical, thermal, and printability properties. The results revealed altered mechanical characteristics, with reduced tensile and flexural properties compared with pure PLA. However, these values are at an acceptable level for non-structural applications. Compared with previous works, the filament developed in the present work is found out to be second strongest among the cellulose fiber-reinforced PLA filaments. 3D printing with the composite filament encountered no significant issues. A modified mixing method improved mechanical characteristics, although 3D-printed samples showed deteriorated mechanical characteristics due to poor interfacial bonding. This research introduces an environmentally viable strategy for advancing 3D printing technology by integrating banana fibers into PLA filament. The proposed strategy can be effectively utilized in making cellulose/PLA filaments for 3D printing applications. This innovative approach preserves PLA's natural biodegradability while carefully managing the integration of banana fibers and their potential effects on mechanical properties. Highlights: Fiber loading influences mechanical, with minimal impact on thermal properties. Solution casting improved fiber/matrix bonding and filler homogeneity. Plasticizing effect reduces the tensile strength. Modified mixing resulted in even filament diameter and improved tensile properties. © 2024 Society of Plastics Engineers.