Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
3 results
Search Results
Item Evaluation of wear resistance of magnesium/glass microballoon syntactic foams for engineering/biomedical applications(Elsevier Ltd, 2019) Manakari, V.; Parande, G.; Doddamani, M.; Gupta, M.Friction and wear behaviour of magnesium/glass microballoon (GMB) foams synthesized by Disintegrated Melt Deposition (DMD) were investigated under dry sliding conditions. The coefficient of friction (?) decreases with increasing GMB content. Mg-25wt.% GMB exhibits ?13% lower ? pure compared to magnesium. Wear resistance of magnesium showed a significant enhancement (?2.5 times) post GMB addition. Abrasion and oxidation were identified as dominant wear mechanisms post worn-surface analysis. Delamination wear, which has traditionally limited the advantages of composites with discontinuous reinforcements in sliding wear conditions for structural and biomedical applications can be effectively addressed by the development of these proposed syntactic foams. © 2019 Elsevier Ltd and Techna Group S.r.l.Item Mechanical behaviour of additively manufactured bioactive glass/high density polyethylene composites(Elsevier Ltd, 2020) Jeyachandran, P.; Bontha, S.; Bodhak, S.; Balla, V.K.; Kundu, B.; Doddamani, M.Bioactive glass (BAG) is a well-known biomaterial that can form a strong bond with hard and soft tissues and can also aid in bone regeneration. In this study, BAG is added to a polymer to induce bioactivity and to realize fused filament fabrication (FFF) based printing of polymer composites for potential orthopaedic implant applications. BAG (5, 10, and 20 wt%) is melt compounded with high density polyethylene (HDPE) and subsequently extruded into feedstock filament for FFF-printing. Tensile tests on developed filaments reveal that they are stiff enough to resist forces exerted during the printing process. Micrography of printed HDPE/BAG reveals perfect diffusion of raster interface indicating proper selection of printing parameters. Micrography of freeze fractured prints shows the homogeneous distribution and good dispersion of filler across the matrix. The tensile, flexural, and compressive modulus of FFF-printed HDPE/BAG parts increases with filler addition. BAG addition to the HDPE matrix enhances flexural and compressive strength. The tensile and flexural behaviour of FFF-prints is comparable to injection molded counterparts. Property maps exhibit the merits of present study over the existing literature pertaining to desired bone properties and polymer composites used in biomedical applications. It is envisioned that the development of HDPE/BAG composites for FFF-printing can lead to possible orthopaedic implants and scaffolds to mimic the bone properties in customised anatomical sites or injuries. © 2020 Elsevier LtdItem Additive Manufacturing of Short Silk Fiber Reinforced PETG Composites(Elsevier Ltd, 2022) Kn, V.; Bonthu, D.; Doddamani, M.; Pati, F.The growing demand for customized medical devices like prostheses, orthoses, and implants is the prime motive for a surge in the investigation of 3D printable biocomposites. PETG (Polyethylene terephthalate glycol) based composites can be a good choice for biomedical applications. Specific characteristics of this material like biocompatibility, ease of formability, stable thermomechanical properties, and high chemical, and abrasion resistance make it suitable for biomedical applications. However, there are very few studies on the 3D printing of PETG-based composites. Development of a robust 3D printing protocol is required for any novel natural fiber reinforced PETG composites. This study presents natural fiber-reinforced PETG biocomposite filament preparation and 3D printing with the developed composite filaments. Silk was used as a filler material due to its high thermal stability and high tensile strength. Composite filaments with 2 wt%, 5 wt%, and 10 wt% silk were prepared using the extrusion process. Further, we developed a protocol for 3D printing with the developed composites to fabricate various 3D structure. Both filaments and printed specimens were characterized morphologically, structurally, and mechanically. The melt flow rate of the filaments decreased with an increase in fiber content which was a bottleneck for printing 10% silk-PETG composites. Micro-CT results validate an increase in void content in filaments on filler addition. The highest flexural modulus and flexural strength were exhibited by 2% silk-PETG printed parts and a 60% increase in compressive modulus compared to pure PETG. Tensile tests show that 2 wt% fiber addition significantly increased elastic modulus (2466.72 MPa) compared to pure PETG (902.81 MPa), whereas the surface roughness of printed composites increased with filler content. Finally, a lower limb prosthetic socket prototype was printed with a desktop 3D printer to demonstrate its potential for biomedical applications. © 2022 Elsevier Ltd