Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
3 results
Search Results
Item The influence of the addition of 4.5 wt.% of copper on wear properties of Al-12Si eutectic alloy(Hashemite University huniv@hu.edu.jo, 2015) Channappagoudar, S.; Kiran Aithal, K.; Sannayallappa, N.; Desai, V.; Mukunda, P.G.The influence of 4.5 wt.% copper addition on wear behavior of as-cast Al-12Si alloy prepared by gravity casting is investigated in dry sliding against a steel counterface using a pin-on-disk apparatus. The microstructures of test alloys and worn surfaces were examined by scanning electron microscopy and energy dispersing X-ray spectroscopy. The addition of copper to the binary Al-12Si alloy led to the precipitation of CuAl2 phase. Copper addition resulted in a refinement of ?-Al and a minor modification of eutectic Si. The Al-12Si-4.5Cu alloy showed a higher wear resistance as compared to Al-12Si binary eutectic alloy. © 2015 Jordan Journal of Mechanical and Industrial Engineering. All rights reserved.Item Tribological behaviour of monolayer and multilayer Ti-based thin solid films deposited on alloy steel(Institute of Physics Publishing helen.craven@iop.org, 2019) V Badiger, P.V.; Desai, V.; Ramesh, M.R.; Joladarashi, S.; Gourkar, H.The fretting wear and adhesive wear resistance of Ti-based thin solid films deposited on MDN121 steel substrate are evaluated. Plasma-assisted cathodic arc evaporation technique is used to develop the TiC-C monolayer coating and Ti/TiN/TiCN/TiN/TiCN multilayer coatings used in the study. FESEM-EDS, nanoindentation, Raman spectroscopy, optical profiler, and confocal microscope are used to characterise the coatings and wear tracks. Diamond-like carbon is observed in the microstructure of both the coatings. During the fretting analysis, the coefficient of friction (COF) is reduced by 68.49% in the case of the TiC-C monolayer coating and 42.46% in the Ti multilayer coatings as compared to the substrate. The volumetric wear loss of the TiC-C monolayer coating is lower than the multilayer coating. The wear surface morphology reveals the abrasive form of the fretting wear mechanism in both the monolayer and multilayer coatings whereas the galling failure in the substrate. During adhesive wear, the COF is reduced by 71.73% in the monolayer coating and 59.33% in the multilayer coatings compared to the substrate. The monolayer coating exhibits low friction and low wear rate as compared to the multilayer coating. © 2018 IOP Publishing Ltd.Item Microstructural evolution and cyclic oxidation behavior of HVOF-sprayed NiCrSi and NiCrC coatings on T11 steel(Elsevier Inc., 2024) Medabalimi, S.; Hebbale, A.M.; Singh, R.; Desai, V.; Ramesh, M.R.This study analyzes NiCrSi and NiCrC coatings developed on low alloy ferritic stainless steel (grade T11) through the HVOF spraying technique. The coatings were characterized by their phase constitution, microstructure, cyclic oxidation behavior, and hardness. X-ray diffraction (XRD) analysis confirmed the presence of the NiCr solid solution matrix as the primary phase in both coatings. Moreover, the microstructure of the NiCrSi coating included the hard intermetallic compounds like Cr?Si and Ni?Si and the NiCrC coating contained the hard phases like Cr?C? and Ni?C which improved the hardness and the wear resistance of the coatings. Microhardness measurements revealed that the coatings had an average hardness of 300 ± 50 HV, significantly greater than the substrate hardness of 225 ± 25 HV. Cyclic oxidation tests were carried out at 700 °C revealed that both the coatings showed a lower weight gain than the uncoated substrate, suggesting enhanced oxidation resistance. This was because the protective oxide layers like Cr?O? and SiO? in the NiCrSi coating and Cr?O? and NiO in the NiCrC coating were formed. X-ray analysis establish ed. the presence of these oxides, which inhibited oxygen penetration through the coatings and provided additional protection against oxidation. Therefore, the study revealed that both NiCrSi and NiCrC coatings have good mechanical and oxidation resistance properties, which make them suitable for high-temperature applications where there is a need for improved durability, wear resistance, and protection against oxidation. © 2024