Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item An Improved Finite Element Based Approach to Predict Single Track Geometry During Laser Directed Energy Deposition(Springer Science and Business Media Deutschland GmbH, 2025) Chaurasia, J.K.; Gurugubelli, R.C.; Jinoop, A.N.; Bontha, S.; Paul, C.P.; Bindra, K.S.This paper reports development of a two-dimensional transient finite element based numerical model to predict dimensions of deposited single track during laser directed energy deposition (LDED) of Inconel 625 (IN625) superalloys. The numerical model in the paper is based on two steps where first melt pool dimensions are determined using a transient thermal simulation. The second step accounts for the material addition, where the elements are activated based on the calculation of excess enthalpy. The numerical model is based on the fundamental principles of energy and mass balance. The numerical model also incorporates the fluid dynamics effects by multiplying the correction factor to the thermal conductivity of the material above melting temperature and also compares the track dimensions without considering the correction factor. A comparison of the track height and width obtained from the numerical model at Cf = 1 and 2.5 with experimental measurements was done. The maximum absolute percentage error in the numerical model considering the fluid dynamics effects (Cf = 2.5) is 5% in track height and 9% in track width. The percentage errors in the case of numerical model without fluid dynamics effects (Cf = 1) is 13% in track height and 16% in track width. The numerical model without considering the fluid dynamics effect is found to overpredict the track dimensions in all the cases. © The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd. 2025.Item Study of melt pool geometry and solidification microstructure during laser surface melting of Inconel 625 alloy(Elsevier GmbH, 2021) Chaurasia, J.K.; Jinoop, A.N.; P, P.; Paul, C.P.; Bindra, K.S.; Bontha, S.The present study aims to comprehend thermo-fluid conditions during laser surface melting (LSM) of Inconel 625 (IN625) alloy using experimental and numerical modelling approaches. Nine tracks were melted on an IN625 plate at different laser powers and scan speeds. Melt pool geometry and grain morphology were evaluated using microscopy techniques. A 3-D finite volume model based on heat conduction solidification equation (HCS model) was used to simulate LSM process. Further, HCS model was expanded to include effects of fluid dynamics (HCS-FD model). Both the numerical models were used to predict melt pool geometry, peak temperatures, temperature gradients and cooling rates. The error in predictions of melt pool geometry from the HCS-FD model was lower when compared to the HCS model. The velocity vectors show a strong surface tension driven flow which has resulted in narrow and deeper melt pools in agreement with the cross sectional images of the melted tracks. Further, solidification characteristics were interpreted to obtain inferences about grain size and morphology. © 2021 Elsevier GmbHItem Effect of deposition strategy and post processing on microstructure and mechanical properties of serviced Inconel 625 parts repaired using laser directed energy deposition(Elsevier Ltd, 2024) Chaurasia, J.K.; Jinoop, A.N.; Paul, C.P.; Bindra, K.S.; Balla, V.K.; Bontha, S.In the present work, an attempt is made to understand and explore the repair capabilities of the Laser Directed Energy Deposition (LDED) process on Nickel based superalloy Inconel 625 (IN625). Samples were extracted from a wrought plate of IN625 and then were subjected to a fatigue test to mimic a component in service for repairing. Further, deposition was carried out on these fatigued tensile sample surfaces i.e., Top, Top & bottom, One side and Both sides. The samples were also solution-treated at 1200 °C for 90 mins. Microstructure and mechanical properties were evaluated and then compared between the different deposition strategies and sample heat-treatment conditions. Tensile properties were compared for all the three sample conditions viz. wrought alloy, as repaired and solution treated. Results indicate sound deposition with minimal porosity in all the four deposition strategies using the LDED process with a mean deposit height of 1.02 ± 0.25 mm. Microstructural analysis revealed mixed dendrite and columnar structure in the case of as-deposited samples whereas, solution treated samples exhibited recrystallized equiaxed grains with the presence of annealing twins. The as-deposited samples show a ductile mode of failure with a maximum ultimate strength of 830 MPa, yield strength of 350 MPa and elongation of 72%. For solution treated samples, a maximum ultimate tensile strength of 620 MPa, yield strength of 270 MPa and elongation of 73% were observed. The strength of the material was found to be highly influenced by the solution treatment. © 2023 Elsevier LtdItem Enhanced tribological performance of laser directed energy deposited Inconel 625 achieved through laser surface remelting(Elsevier B.V., 2024) Praharaj, A.K.; Chaurasia, J.K.; Gurugubelli, R.C.; Bontha, S.; Suvin, P.S.Inconel 625 (IN625) is an essential material for the manufacture of turbine blades and seals, aircraft ducting systems, engine components, and pressure valves. Laser Directed Energy Deposition (LDED) process has shown the potential to fabricate IN625 parts with superior mechanical properties and higher corrosion resistance when compared to those fabricated using conventional manufacturing techniques. However, the poor surface quality limits the practical application of LDED fabricated parts, especially in sectors that demand high tribological performance. To this end, this study focuses on improving the surface quality and tribological performance of LDED fabricated IN625 components using Laser Surface Remelting (LSR) as a postprocessing operation. The tribological performance was evaluated using a linear reciprocating ball-on-flat wear test setup. The surface roughness, remelting depth (RD), microstructure, hardness, and tribological performance (coefficient of friction and wear rate) of the remelted (RM) samples were compared with that of as-deposited (AD) samples. Microstructural characterization revealed that LSR resulted in grain refinement, reduced dendrite size, and primary dendritic arm spacing (PDAS). Laser scanning speed effects RD, dendrite size and PDAS via its effect on cooling rates. SEM + EDS analysis confirmed the presence of Laves phase in both AD and RM samples. XRD analysis of RM samples showed an increase in the amount of Laves phase. The refinement in microstructural features and the increased amount of Laves phase among the RM samples led to improvement in microhardness when compared to AD samples. Wear test results revealed a reduction in the coefficient of friction (COF) and wear rate after LSR with wear mechanism being either abrasive or delamination. Reduction in the size of dendrites and refinement in grain size are attributed to the enhanced tribological performance after LSR. © 2023 Elsevier B.V.Item Effect of Build Orientation on Anisotropy in Tensile Behavior of Laser Powder Bed Fusion Fabricated SS316L(Springer, 2024) Thanumoorthy, R.S.; Chaurasia, J.K.; Anil Kumar, V.A.; Pradeep, P.I.; Balan, A.A.S.; Rajasekaran, B.; Sahu, A.; Bontha, S.In the present study, Stainless steel 316L (SS316L) cylindrical specimens were fabricated at two different build orientations and two different laser powers using Laser powder bed fusion process (LPBF). Microstructural characterization such as XRD, SEM, EBSD analysis and tensile testing were carried out on fabricated specimens in stress relieved condition to understand the anisotropic behavior of LPBF printed specimens. Horizontally oriented specimens showed higher tensile strength when compared to vertically oriented specimens for both laser powers. XRD and EBSD phase maps did not reveal the presence of any secondary phases. However, build orientation and laser power affected the crystallite size of the samples. Bimodal grain structure comprising coarse columnar grains and fine equiaxed grains were observed from the micrographs. With variation in build orientation, there was a significant change in the average grain size of the specimens. High dislocation density was observed in horizontally oriented samples built at low laser power because of dislocation annihilation that can occur at high temperatures. However, EBSD analysis revealed random weak crystallographic texture which does not vary significantly with laser power or build orientation. Variation in grain size, grain morphology, sub-grain features and dislocation density are the reasons for the anisotropic tensile behavior observed in LPBF printed SS316L coupons in stress relieved condition. © ASM International 2023.Item Effect of Heat Treatment on Microstructure and Dry Sliding Wear Behavior of Laser Directed Energy Deposited Inconel 625(Springer, 2025) Praharaj, A.K.; Chaurasia, J.K.; Suvin, P.S.; Narayanan, J.A.; Paul, C.P.; Balla, V.K.; Chakrapani, S.K.; Bontha, S.Laser directed energy deposition (LDED) is a promising technology for manufacturing and repair of Inconel 625 (IN625) components used in critical sectors requiring enhanced tribological performance due to harsh operating environments. Hence, the current work focuses on the evaluation of the tribological performance of LDED-built IN625 with the implementation of different heat treatment methods, i.e., solution treatment (ST), direct aging (AG), and solution treatment + aging (ST + AG). A detailed microstructural analysis, hardness, and wear testing were performed for the as-deposited (AD) and heat-treated (HT) samples, and the results were compared. The analysis revealed coarser grains in the case of ST and ST + AG samples, whereas finer grains for AD and AG samples, indicating grain coarsening after solution treatment. Further, the brittle laves phase gets dissolved after ST, whereas the AG and ST + AG samples resulted in the precipitation of metal carbides and strengthening phases. The microhardness of the ST sample (193.2 HV) was lower compared to the AD (211.6 HV) sample, whereas the AG and ST + AG samples exhibited 25.6 and 9.3% higher hardness than the AD sample. Considering tribological performance, the AG sample illustrated a maximum reduction of 61.4% in the coefficient of friction (COF) and 36.5% in wear rate when compared to the AD sample. This could be attributed to the presence of finer grains and strengthening phases. © ASM International 2025.