Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Enhancement of the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag(Elsevier Ltd, 2017) Saha, S.; C, C.Research efforts have been made continuously to establish fly ash based geopolymer as an alternative binder material for the production of fresh concrete because production of Ordinary Portland Cement degrades the environment by huge emissions of carbon-di-oxide and also by consuming lot of natural resources. But most of the study reveals, fly ash based geopolymer paste needs more time to get set when it is cured at ambient temperature. As a result, it is quite impractical to use fly ash based geopolymer paste as an alternative to Ordinary Portland Cement in faster construction. In this study, an effort has been made to enhance the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag at various percentage levels. Microstructure of the geopolymer paste is studied using Scanning Electron Microscopy. Result of this investigation shows that significant improvement on setting time and compressive strength can be obtained by adding ground granulated blast furnace slag in the mixes. © 2017 Elsevier LtdItem Investigation on the potential use of recycled fine aggregate to produce geopolymer mortar mix(ASTM International, 2019) Saha, S.; C, C.The utilization of construction and demolition waste (C&DW) partially or fully for various purposes in construction industries is one of the most significant solutions to overcome the scarcity of raw materials and disturbances of the environmental system. On the other hand, geopolymer is being tried to be established as an alternative sustainable binder material for ordinary portland cement. In the present study, with the thought of promoting of sustainability, an attempt has been made to use concrete wastes as recycled fine aggregate (RFA) partially to produce fly ash (FA)-based geopolymer mortar. The workability, water absorption, compressive strength at 3, 7, 28, and 56 days, volume change behavior, and chloride permeability of the produced FA-based geopolymer mortar were determined. The effects of RFA, the ratio of alkali liquid (AL) to FA, and different curing regimes on these properties of mortar mix also discussed. The morphology and microstructures of the samples taken from the mortar mix, which were observed having the highest strength under different curing regimes, were studied using scanning electron microscopy (SEM). The experimental results indicate lower workability, higher water absorption capacity, and higher drying shrinkage of geopolymer mortar mix that has more RFA content in the mix, but the compressive strength of the geopolymer mortar mix started decreasing after a certain percentage of RFA content in the mix. Utilization of that certain percentage of RFA will help us to minimize the consumption of natural fine aggregates and reduce the disturbances generated by unorganized dumping of C&DW. © 2019 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.Item Strength and shrinkage properties of heat-cured fly ash-based geopolymer mortars containing fine recycled concrete aggregate(ASTM International, 2020) Saha, S.; C, C.Geopolymer has obtained significant importance as an alternative eco-friendly binder material for ordinary portland cement (OPC) as it can be produced from the reaction between the industrial by-product materials rich in alumina, silica, and alkaline solutions. Therefore, usage of geopolymer effectively in the construction industry will help to reduce the consumption of a huge quantity of natural resources for the energy processes required for the production of OPC. It is also one of important solution to control carbon dioxides emission by the usage of OPC. On the other hand, using construction and demolition waste (C&DW) as the source of recycled aggregates in construction industry helps to reduce the huge consumption of natural aggregates and protect the environment from the disturbances caused by the unorganized dumping of C&DW. In this study, an attempt has been madeto produce fly ash (FA)-based geopolymer mortar mixes using C&DW effectively as fine aggregates partially. The effects of recycled fine aggregates (RFA), the ratio of alkaline liquid (AL) to FA, and duration of heat curing on the properties of the produced geo-polymer mortar mixes have been discussed in this article. To determine the influence of RFA on the strength and volume change behavior of mixes, natural fine aggregates were replaced by RFA at 0, 10, 20, 30, 40, and 50 % by mass. The AL/FA ratio was adopted as 0.4 and 0.6. Higher compressive strength was observed for most of the mortar mixes having RFA up to 20 %, and higher drying shrinkage value was found for the mixes with higher RFA content. Scanning electron microscopy (SEM) images were also studied for knowledge about the signature of the formed structures in the mortar mixes, which were observed having higher strength. © © 2019 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.Item EXPERIMENTAL INVESTIGATIONS ON THE PROPERTIES OF CONCRETE CONTAINING PRE-SOAKED RECYCLED FINE AGGREGATE(Associated Cement Companies Ltd., 2022) Saha, S.; C, C.; Ganiger, M.S.; Sajjan, S.Recycled fine aggregate (RFA) becomes very significant and promising alternative materials for natural fine aggregate (river sand) to be used in the production of concrete. But, most of the past research works indicated higher water absorption capacity of RFA as one of the key factor to affect the properties of fresh concrete. Therefore, an experimental attempt has been made to address the issues related to water absorption capacity of RFA by soaking it in water for 24 hours prior to use as alternative fine aggregate for the production of the fresh concrete. Mechanical properties of concrete such as compressive strength, splitting tensile strength, and flexural strength, and durability properties such as resistance against acidic and alkaline environment, chloride permeability test for ordinary Portland cement (OPC) and Portland pozzolana cement (PPC) based concrete mixes made with soaked recycled fine aggregates (SRFA) are determined, and analysed. For OPC, and PPC based concrete, respectively 4.32, and 20.75 % in compressive strength at 28 days; 2.69, and 27.24 % increase in flexural strength; 6.38, and 40 % increase in splitting tensile strength at 28 days were observed for the concrete mixes with SRFA compared to the mixes with RFA. Experimental results indicated notable improvement of the mechanical, and durability properties of concrete mixes when recycled fine aggregates were soaked in water prior to use. © 2022, Associated Cement Companies Ltd.. All rights reserved.Item PERFORMANCE ASSESSMENT OF STEEL SLAG AGGREGATES AS PARTIAL REPLACEMENT OF RIVER SAND IN CONCRETE(Associated Cement Companies Ltd., 2023) Sundaramoorthi, S.; Hemalatha, T.; C, C.In order to bring sustainability in construction, nowadays, many industrial solid wastes are used as a partial replacement for cement as well as aggregates. Using industrial wastes in construction solves dual problem of waste disposal and depletion of natural resources. Steel aggregate is one such industrial solid waste having potential to replace the conventional river sand. In this study, an attempt has been made to investigate the performance of steel slag aggregates in concrete as a partial replacement for conventional river sand. Three mixes were made for this study, first mix made of ordinary Portland cement (OPC) and 100 % river sand (0M0), second mix (0M50) made of OPC and 50 % river sand replaced by slag aggregates and third mix (25M50) made of 25 % fly ash and 75 % OPC, and 50 % slag aggregates. Tests for assessing the mechanical and durability properties were conducted. The results showed that the strength and durability of concrete made with steel slag aggregate and river sand were comparable. This study shows the suitability of using 50% steel slag aggregates as a partial replacement for river sand in concrete. © 2023, Associated Cement Companies Ltd.. All rights reserved.Item Performance and microstructural investigations of processed lateritic fine aggregates in blended cement mortars exposed to elevated temperatures(Emerald Publishing, 2023) Basavana Gowda, S.N.; Yaragal, S.C.; C, C.; Goudar, S.K.Purpose: In recent years, fire accidents in engineering structures have often been reported worldwide, leading to a severe risk to life and property safety. The present study is carried out to evaluate the performance of Ground Granulated Blast Furnace Slag (GGBS) and fly ash–blended laterized mortars at elevated temperatures. Design/methodology/approach: This test program includes the replacement of natural river sand with lateritic fine aggregates (lateritic FA) in terms of 0, 50 and 100%. Also, the ordinary Portland cement (OPC) was replaced with fly ash and GGBS in terms of 10, 20, 30% and 20, 40 and 60%, respectively, for producing blended mortars. Findings: This paper presents results related to the determination of residual compressive strengths of lateritic fine aggregates-based cement mortars with part replacement of cement by fly ash and GGBS exposed to elevated temperatures. The effect of elevated temperatures on the physical and mechanical properties was evaluated with the help of microstructure studies and the quantification of hydration products. Originality/value: A sustainable cement mortar was produced by replacing natural river sand with lateritic fine aggregates. The thermal strength deterioration features were assessed by exposing the control specimens and lateritic fine aggregates-based cement mortars to elevated temperatures. Changes in the mechanical properties were evaluated through a quantitative microstructure study using scanning electron microscopy (SEM) images. The phase change of hydration products after exposure to elevated temperatures was qualitatively analyzed by greyscale thresholding of SEM images using Image J software. © 2023, Emerald Publishing Limited.