Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
14 results
Search Results
Item Use of concrete wastes as the partial replacement of natural fine aggregates in the production of concrete(Springer, 2019) Saha, S.; C, C.; Vinay, K.Due to rapid development of construction industries in various dimensions, demand for construction materials is also gaining high momentum. Therefore, availability of natural sources of construction materials is going to be in decreasing trend to cope up with the high demand. Again currently, quantity of construction and demolition waste is also going too high day by day. Reuse of these construction and demolition waste is one of the promising solutions to protect natural fine aggregates. This study aims at investigations the possibility of the usage of these construction and demolition wastes to produce the fresh concrete with desirable properties. Natural fine aggregates (river sand) are replaced by the recycled fine aggregates by the different percentage levels for the production of fresh concrete. A comparative interpretation on the strength characteristics of the concrete produced with Ordinary Portland Cement and Portland Pozzolana Cement is also presented and discussed in this paper. © Springer Nature Singapore Pte Ltd. 2019.Item Use of foundry sand as partial replacement of natural fine aggregate for the production of concrete(Springer, 2019) Saha, S.; C, C.; More, A.P.The scarcity of natural fine aggregate becomes prominent in the present scenario due to high consumption of natural fine aggregate as the demand for concrete is increasing day by day. As a result, environmental degradation also becomes very significant. In this experimental study, an effort has been made to study the feasibility of using foundry sand as partial replacement for natural fine aggregate to produce concrete with desired properties. Physical and mechanical properties of the produced concrete were studied by incorporating foundry sand, 10, 20, 30, and 40% of the mass of total fine aggregate in the mixes. For achieving the desired strength of concrete mixes, 30% replacement of natural fine aggregates by foundry sand was observed in this work to be considered for the production of fresh concrete. Use of certain percentage of foundry sand as alternative for natural fine aggregate to produce concrete will lead to protect the natural resources, save the environmental system, and promote sustainability in concrete industries. © Springer Nature Singapore Pte Ltd. 2019.Item Strength characteristics of laterized mortars using processed laterite(Springer, 2019) Basavana Gowda, S.N.; C, C.; Yaragal, S.C.The rapid pace of population growth in India has enforced the construction industry to use construction materials at an accelerated rate leads to the exhaustion of natural resources. Large-scale constructions have a severe influence on the environment instigating many threats either directly or indirectly like exhaustion of the river due to unscientific sand mining being done at a frightening level, etc. To address this issue, it is required to find substitutes for river sand for producing mortars. One among the locally available marginal resource is laterite. In this study, an attempt is made to study the performance of cement mortars using laterite as fine aggregate in replacement levels of 0, 25, 50, 75 and 100% to natural fine aggregates (river sand). Studies were carried out in two stages, initially river sand is replaced with laterite quarry waste (unprocessed laterite), and then it is replaced with the processed laterite. The flowability and compressive strength characteristics of mortars are studied. Results indicate that, the decrease in compressive strength of mortars with increase in replacement levels of river sand by unprocessed laterite was more, when compared to mortars with processed laterite. However, there is only 13% reduction in strength for laterized mortar with 100% processed laterite when compared to control mortar is observed. © Springer Nature Singapore Pte Ltd. 2019.Item An experimental investigation to determine the properties of fly ash based geopolymers as per indian standards(Springer, 2019) Saha, S.; C, C.Production of ordinary Portland cement requires huge quantity of natural resources and also releases huge quantity of carbon dioxide into the atmosphere. Research efforts have been continuing to establish geopolymer as an alternative cementitious material for the replacement of ordinary Portland cement. This paper presents the study to find out the properties of fly ash based geopolymer paste and 28 days compressive strength of geopolymer mortar. Standard consistency, setting time of geopolymer paste has been determined using vicat’s apparatus (according to Indian Standards), which is followed for cement paste, varying the concentration of sodium hydroxide solution from 6 to 16 M. Results indicate higher standard consistency, more time required for setting for fly ash based geopolymer than that of cement paste. Compressive strength of the geopolymer paste and mortar 17 specimens increases with the increase of the concentration of sodium hydroxide solution and decrease beyond 14 M. © 2019, Springer Nature Singapore Pte Ltd.Item Enhancement of the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag(Elsevier Ltd, 2017) Saha, S.; C, C.Research efforts have been made continuously to establish fly ash based geopolymer as an alternative binder material for the production of fresh concrete because production of Ordinary Portland Cement degrades the environment by huge emissions of carbon-di-oxide and also by consuming lot of natural resources. But most of the study reveals, fly ash based geopolymer paste needs more time to get set when it is cured at ambient temperature. As a result, it is quite impractical to use fly ash based geopolymer paste as an alternative to Ordinary Portland Cement in faster construction. In this study, an effort has been made to enhance the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag at various percentage levels. Microstructure of the geopolymer paste is studied using Scanning Electron Microscopy. Result of this investigation shows that significant improvement on setting time and compressive strength can be obtained by adding ground granulated blast furnace slag in the mixes. © 2017 Elsevier LtdItem Investigation on the potential use of recycled fine aggregate to produce geopolymer mortar mix(ASTM International, 2019) Saha, S.; C, C.The utilization of construction and demolition waste (C&DW) partially or fully for various purposes in construction industries is one of the most significant solutions to overcome the scarcity of raw materials and disturbances of the environmental system. On the other hand, geopolymer is being tried to be established as an alternative sustainable binder material for ordinary portland cement. In the present study, with the thought of promoting of sustainability, an attempt has been made to use concrete wastes as recycled fine aggregate (RFA) partially to produce fly ash (FA)-based geopolymer mortar. The workability, water absorption, compressive strength at 3, 7, 28, and 56 days, volume change behavior, and chloride permeability of the produced FA-based geopolymer mortar were determined. The effects of RFA, the ratio of alkali liquid (AL) to FA, and different curing regimes on these properties of mortar mix also discussed. The morphology and microstructures of the samples taken from the mortar mix, which were observed having the highest strength under different curing regimes, were studied using scanning electron microscopy (SEM). The experimental results indicate lower workability, higher water absorption capacity, and higher drying shrinkage of geopolymer mortar mix that has more RFA content in the mix, but the compressive strength of the geopolymer mortar mix started decreasing after a certain percentage of RFA content in the mix. Utilization of that certain percentage of RFA will help us to minimize the consumption of natural fine aggregates and reduce the disturbances generated by unorganized dumping of C&DW. © 2019 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.Item Characterization and performance of processed lateritic fine aggregates in cement mortars and concretes(Elsevier Ltd, 2019) Yaragal, S.C.; Basavana Gowda, S.N.; C, C.Availability of river sand is becoming scarce, due to rapid increase in infrastructure projects in India. Acute shortage of river sand, has led to indiscriminate sand mining. Adverse effect of sand mining includes river bank erosion, river bed degradation, loss of biodiversity and deterioration of river water quality and ground water availability. To address the above issues, research efforts are on, to find substitutes for river sand to be used as fine aggregate in mortars and concretes. One among the locally available resources is laterite. Laterite is a product of tropical or sub-tropical weathering, which is an abundant soil material in many parts of India. An attempt has been made to characterize the processing technique to obtain good quality lateritic fine aggregates (lateritic FA). Experiments were designed and conducted to study the performance of lateritic FA as replacement to river sand, in cement mortars and concretes. Processed lateritic FA in replacement levels of 0, 25, 50, 75 and 100 wt% to river sand at all fineness levels (Zone I to Zone IV as per Indian standards) is considered. Microstructure studies were conducted to understand the arrangement of river sand and lateritic FA with cement matrix and their Interfacial Transition Zones (ITZ) using Scanning Electron Microscope (SEM). The workability and compressive strength characteristics of cement mortars and concretes are evaluated. Laterized mortars with Zone III and Zone IV fine aggregates, at all replacement levels, result in the same compressive strengths as those of control mortars. Suitable strength enhancement technique has been attempted to achieve strengths of Zone I and Zone II lateritic fine aggregates based mortars at 100 wt% replacement, to achieve strength at least equal to or more than those of control mortars. Laterized concretes have achieved nearly the same strengths as those of control concretes, at all replacement levels and for all fineness levels (Zone I to Zone IV). © 2018 Elsevier LtdItem Performance of eco-friendly mortar mixes against aggressive environments(Techno-Press info@techno-press.com, 2020) Saha, S.; C, C.; Gupta, P.Past research efforts already established geopolymer as an environment-friendly alternative binder system for ordinary Portland cement (OPC) and recycled aggregate is also one of the promising alternative for natural aggregates. In this study, an effort was made to produce eco-friendly mortar mixes using geopolymer as binder and recycled fine aggregate (RFA) partially and study the resistance ability of these mortar mixes against the aggressive environments. To form the geopolymer binder, 70% fly ash, 30% ground granulated blast furnace slag (GGBS) and alkaline solution comprising of sodium silicate solution and 14M sodium hydroxide solution with a ratio of 1.5 were used. The ratio of alkaline liquid to binder (AL/B) was also considered as 0.4 and 0.6. In order to determine the resistance ability against aggressive environmental conditions, acid attack test, sulphate attack test and rapid chloride permeability test were conducted. Change in mass, change in compressive strength of the specimens after the immersion in acid/sulphate solution for a period of 28, 56, 90 and 120 days has been presented and discussed in this study. Results indicated that the incorporation of RFA leads to the reduction in compressive strength. Even though strength reduction was observed, eco-friendly mortar mixes containing geopolymer as binder and RFA as fine aggregate performed better when it was produced with AL/B ratio of 0.6. © 2020 Techno-Press, Ltd.Item Strength and shrinkage properties of heat-cured fly ash-based geopolymer mortars containing fine recycled concrete aggregate(ASTM International, 2020) Saha, S.; C, C.Geopolymer has obtained significant importance as an alternative eco-friendly binder material for ordinary portland cement (OPC) as it can be produced from the reaction between the industrial by-product materials rich in alumina, silica, and alkaline solutions. Therefore, usage of geopolymer effectively in the construction industry will help to reduce the consumption of a huge quantity of natural resources for the energy processes required for the production of OPC. It is also one of important solution to control carbon dioxides emission by the usage of OPC. On the other hand, using construction and demolition waste (C&DW) as the source of recycled aggregates in construction industry helps to reduce the huge consumption of natural aggregates and protect the environment from the disturbances caused by the unorganized dumping of C&DW. In this study, an attempt has been madeto produce fly ash (FA)-based geopolymer mortar mixes using C&DW effectively as fine aggregates partially. The effects of recycled fine aggregates (RFA), the ratio of alkaline liquid (AL) to FA, and duration of heat curing on the properties of the produced geo-polymer mortar mixes have been discussed in this article. To determine the influence of RFA on the strength and volume change behavior of mixes, natural fine aggregates were replaced by RFA at 0, 10, 20, 30, 40, and 50 % by mass. The AL/FA ratio was adopted as 0.4 and 0.6. Higher compressive strength was observed for most of the mortar mixes having RFA up to 20 %, and higher drying shrinkage value was found for the mixes with higher RFA content. Scanning electron microscopy (SEM) images were also studied for knowledge about the signature of the formed structures in the mortar mixes, which were observed having higher strength. © © 2019 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.Item Compressive strength prediction of SCC containing fly ash using SVM and PSO-SVM models(Structural Engineering Research Centre, 2021) Rajeshwari, R.; Mandal, S.; C, C.Self-Compacting Concrete (SCC), is a highly workable material, compacted by its self weight without observable segregation and bleeding. In this study, Support Vector Machine (SVM) and particle swarm optimization based SVM models are employed to predict the 28 days compressive strength of individual SCC mix. A database of 62 no’s of SCC compressive strength from literature with cement partially replaced by fly ash is used for training the models. The test data consists of two groups, an individual study consisting of 9 datasets and other combination of three studies with 19 datasets tested separately. Similar input parameters from the train data is extended for testing the models prediction accuracy. Statistical parameters such as correlation coefficient, root mean square error and scatter index are used to evaluate the models’ prediction results. The particle swarm optimization based SVM model is capable of selecting appropriate SVM parameters to increase the prediction accuracy. From the results, it is seen that both SVM and particle swarm optimized SVM models have good capability in predicting the SCC compressive strength. © 2021, Structural Engineering Research Centre. All rights reserved.