Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
16 results
Search Results
Item High stable zinc tungstate electrode for electrochemical supercapacitor(American Institute of Physics Inc. subs@aip.org, 2020) Dhanush, P.C.; Brijesh, K.; Vinayraj, S.This paper aims to develop a way for synthesising Zinc Tungstate (ZnWO4) by Microwave method. Which is simpler easier and better than hydrothermal synthesis. Formation of the crystal microstructures were verified with the aid of Powder X-Ray Diffraction (XRD), and further, morphologies were investigated upon using Field Emission Scanning Electron Microscope (FESEM). The implications in the energy storage devices were examined by preparing a pseudo capacitor. The electrochemical characteristics were analysed by using three-electrode system and its performance was evaluated with the assistance of Cyclic Voltammetry (CV) and Electrochemical Impedance Spectroscopy (EIS). The result presented the specific capacitance as 79 Fg-1 for a scan rate of 1mVs-1. The ZnWO4 as an active material retains 96.52% stability up to 1000 cycles. A significant increase in the impedance for lower frequencies can be observed for the material after 1000 cycles when compared to that of the first cycle. © 2020 Author(s).Item Advanced Electrolyte Additives for Lithium-Ion Batteries: Classification, Function, and Future Directions(American Chemical Society, 2025) Brijesh, K.; Jareer, M.; Lakshmi Sagar, G.; Mukesh, P.; Alagarsamy, A.; Mandal, D.; Nagaraja, H.S.; Shahgaldi, S.Lithium-ion batteries (LIBs) are widely employed as energy storage devices, particularly in portable electronics and electric vehicles, owing to their high energy density and efficiency. Among the key components of LIBs, the electrolyte plays a crucial role in determining capacity, cycling stability, rate performance, the electrode/electrolyte interface, and overall battery efficiency. However, traditional electrolytes face significant challenges, including severe structural degradation and interfacial side reactions under high-voltage and high-temperature conditions. Protective layers, such as the cathode-electrolyte interphase (CEI) and solid-electrolyte interphase (SEI), are essential for addressing these issues. These layers inhibit electron transfer while allowing lithium-ion (Li+) transport, preserving the structural and electrochemical integrity of the battery. A cost-effective strategy to further enhance the electrode-electrolyte interface and boost LIB performance is the incorporation of carefully designed electrolyte additives. While some articles discuss the use of electrolyte additives in LIBs, there is a lack of detailed studies classifying these additives based on their chemical composition-based grouping. Such a classification enables a more focused examination of the roles and mechanisms by which these additives improve LIB performance. This review paper bridges this gap by examining various electrolyte additives and their contributions to enhancing the safety and performance of next-generation LIBs. It provides valuable insights into the current progress and challenges associated with additives in liquid electrolytes. The article is organized into seven sections, addressing boron-based electrolyte additives (Section 2), sulfur-based electrolyte additives (Section 3), phosphorus-based electrolyte additives (Section 4), fluorine-based electrolyte additives (Section 5), and nitrogen-based electrolyte additives (Section 6). Each section discusses specific examples, the formation of SEI and CEI layers, and the electrochemical properties of these additives. Furthermore, the article concludes with a summary and outlook, advocating for continued advancements in electrolyte engineering for LIBs. © 2025 American Chemical Society.Item Chemically prepared Polypyrrole/ZnWO 4 nanocomposite electrodes for electrocatalytic water splitting(Elsevier Ltd, 2019) Brijesh, K.; Bindu, K.; Shanbhag, D.; Nagaraja, H.S.ZnWO 4 , PPy, and PPy/ZnWO 4 nanoparticles were prepared using chemical synthesis. The structural, compositional and morphological properties of the prepared samples have been investigated using XRD, FTIR, SEM, and HRTEM respectively. The powder XRD reveals the monoclinic wolframite structure for both ZnWO 4 and PPy/ZnWO 4 nanocomposite. SEM confirms the wrapping of ZnWO 4 with PPy. The electrodes of ZnWO 4 , PPy, and PPy/ZnWO 4 have been tested as bifunctional electrocatalyst towards HER and OER using constant current chronopotentiometry (CP) and Linear Sweep Voltammetry (LSV). The electrochemical surface area and the electrocatalytic activity PPy/ZnWO 4 nanocomposite towards HER and OER are greater than that of pure ZnWO 4 and PPy. The Tafel slope of PPy/ZnWO 4 nanocomposite is 76 and 84 mV dec ?1 in 0.5 M H 2 SO 4 and 1 M KOH at room temperature for HER and OER respectively. The results suggest that PPy/ZnWO 4 nanocomposite is a good candidate for the bifunctional electrocatalyst for water splitting. © 2018 Hydrogen Energy Publications LLCItem Lower Band Gap Sb/ZnWO4/r-GO Nanocomposite Based Supercapacitor Electrodes(Springer New York LLC barbara.b.bertram@gsk.com, 2019) Brijesh, K.; Nagaraja, H.S.Sb/ZnWO4/r-GO nanocomposite has been prepared by a single step solvothermal method. The crystal structure of the prepared nanocomposite has been characterized using a powder x-ray diffractometer (XRD). The optical properties of the prepared nanocomposite were studied using UV–visible spectroscopy and photoluminescence. The energy band gap of 3.52 eV is obtained for the ZWS-5 nanocomposite using Tauc plots. For both Sb/ZnWO4 and Sb/ZnWO4/r-GO nanocomposite XRD shows the monoclinic Wolframite structure. The supercapacitor performance of the prepared samples was carried out using electrochemical techniques such as cyclic voltammetry, galvanostatic charge–discharge and electrochemical impedance spectroscopy. The nanocomposite ZWS-5 exhibits a specific capacitance of 102 F/g, which is higher than pristine ZWS specific capacitance of 64 F/g. Both ZWS and ZWS-5 electrodes show good capacitance retention proficiency even after 1000 cycles. © 2019, The Minerals, Metals & Materials Society.Item Dual electrochemical application of r-GO wrapped ZnWO4/Sb nanocomposite(Institute of Physics Publishing helen.craven@iop.org, 2019) Brijesh, K.; Bindu, K.; Amudha, A.; Nagaraja, H.S.ZnWO4/Sb nanorods and r-GO-ZnWO4/Sb nanocomposite have been prepared using a single step solvothermal method. The prepared nanocomposites have been characterized using x-ray diffractometer (XRD), Scanning Electron Microscope (SEM), High Resolution Transmission Electron Microscope (HR-TEM), Raman and Brunauer-Emmett-Teller (BET). The x-ray photoelectron spectroscopy (XPS) technique was used to determine the elemental composition of ZWS-5 (5 mg r-GO-ZnWO4/Sb) composite. The XRD reveals the monoclinic wolframite structure of ZnWO4/Sb and r-GO-ZnWO4/Sb. SEM and HRTEM confirms that the ZnWO4/Sb has been decorated on the r-GO sheets. The electrochemical performance of the prepared samples towards the Hydrogen Evolution Reaction (HER) and dopamine sensing has been tested using electrochemical techniques. Onset potential of 265 mV @10 mA cm-2, lower Tafel slope (95 mV dec-1), high electrochemical surface area (1383.216 m2g-1) and high specific site density (18.551 06 × 1021 g-1) of ZWS-5 reveals the high electrocatalytic activity of the composite towards HER. Chronoamperometric dopamine sensing shows that ZWS-5 has the superior sensing performance with highest specific sensitivity (723 ?A ?M-1 ?g-1), lowest limit of detection (0.9624 ?M), along with a good selectivity. Results suggest that the r-GO-ZnWO4/Sb nanocomposite is a good candidate for the HER and electrochemical dopamine sensor. The incorporation of r-GO nanosheets with ZnWO4/Sb (ZWS) nanorods enhances the specific and electrochemical surface area, which accounts for the high electrocatalytic activity of the composite. © 2019 IOP Publishing Ltd.Item ZnWO4/r-GO nanocomposite as high capacity anode for lithium-ion battery(Springer, 2020) Brijesh, K.; Nagaraja, H.S.The pristine ZnWO4 and ZnWO4/r-GO nanocomposite synthesized by the facile solvothermal method were tested as anode materials for lithium-ion battery. Ex situ X-ray photoelectron spectroscopy (XPS) confirms the elemental composition of the pristine ZnWO4 and ZnWO4/r-GO nanocomposite. The ZnWO4/r-GO nanocomposite shows mesoporous nature and exhibits 50.802 m2 g?1 BET specific surface area, which is higher than that of pristine ZnWO4. In addition, the electrochemical property of the pristine ZnWO4 and ZnWO4/r-GO nanocomposite investigated using 2032 half-cell reveals that GO enhances the electrochemical property of the ZnWO4. The ZnWO4/r-GO nanocomposite not only exhibits higher discharge capacity of 1158 mAh g?1 at 100 mA g?1 but also shows longer and stable cycle life at 300 mA g?1 current density. The ZnWO4/r-GO nanocomposite exhibits 80.74% capacity retention even after 500 cycles. The synergetic effect of r-GO and ZnWO4 improves the capacity, columbic efficiency, and stability of the material. The results indicate that ZnWO4/r-GO nanocomposite is an interesting anode material for Li-ion battery with higher capacity complemented with stability compared to pristine ZnWO4. [Figure not available: see fulltext.]. © 2020, Springer-Verlag GmbH Germany, part of Springer Nature.Item Monoclinic Wolframite ZnWO4/SiO2 nanocomposite as an anode material for lithium ion battery(Elsevier B.V., 2020) Brijesh, K.; Dhanush, P.C.; Vinayraj, S.; Nagaraja, H.S.Herein, we report the preparation and characterization of the ZnWO4 and ZnWO4/SiO2 nanocomposite. The ZnWO4/SiO2 nanocomposite exhibits 570 mAh g?1 discharge capacity and 314 mAh g?1 charge capacity at 10 mA g?1 for the primary cycle. The increasing amount of SiO2 in the ZnWO4/SiO2 nanocomposite increases the overall performance of the composite. The synergetic effect between the ZnWO4 and SiO2 enhances the rate capability, specific capacity, cycle stability and coloumbic efficiency of the composite. The good electrochemical performance of ZnWO4/SiO2 nanocomposite makes it a promising anode for Lithium ion battery. © 2020 Elsevier B.V.Item ZnWO4/SnO2@r-GO nanocomposite as an anode material for high capacity lithium ion battery(Elsevier Ltd, 2020) Brijesh, K.; Vinayraj, S.; Dhanush, P.C.; Bindu, K.; Nagaraja, H.S.Lithium ion battery (LIB) is widely used energy storage device. Herein, we report the preparation of ZnWO4/SnO2 nanocomposite and ZnWO4/SnO2@r-GO nanocomposite via solvothermal method. The structural, elemental and morphological properties of the prepared samples are characterized using x-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDAX), high-resolution transmission electron microscopy (HR-TEM), Brunauer-Emmett-Teller (BET) measurements, Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) techniques. The prepared samples are tested as an anode for LIB. The ZnWO4/SnO2 (5%) nanocomposite delivers initial discharge capacity of 882 mAh g?1 at a current density of 100 mA g?1, while, the specific capacity increases with the increase of SnO2 upto 10% tested in present case. Further, ZnWO4/SnO2@r-GO nanocomposite exhibits a discharge capacity of 1486 mAh g?1 which is higher than that of ZnWO4/SnO2 nanocomposite. In addition, after 500 cycles ZnWO4/SnO2@r-GO nanocomposite exhibits 89.8% cycle life and 98% of discharge capacity retention. These results indicate that, ZnWO4/SnO2@r-GO nanocomposite is a promising anode material for LIB. © 2020 Elsevier LtdItem GeO2/ZnWO4@CNT nanocomposite as a novel anode material for lithium-ion battery(Springer, 2020) Brijesh, K.; Nagaraja, H.S.Single-walled carbon nanotube (SWCNT) wrapped GeO2/ZnWO4 nanocomposite was prepared by single-step solvothermal method. In this work, GeO2/ZnWO4 nanocomposites were prepared by varying the molar percentage of GeO2 and by further adding SWCNT for the composite to boost the electrochemical performance. The prepared GeO2/ZnWO4 nanocomposites and GeO2/ZnWO4@CNT nanocomposite are used as anode material for lithium-ion battery (LIB). As expected, GeO2/ZnWO4@CNT nanocomposite exhibits higher capacities and good rate capability than the GeO2/ZnWO4 nanocomposite. The GeO2/ZnWO4@CNT nanocomposite exhibits 930 mAh g?1 discharge capacity and 533 mAh g?1 charge capacity for the initial cycle at 100 mAh g?1 in the voltage range of 0.01–3 V (vs. Li+/Li). Even at high current density of 500 mAh g?1, GeO2/ZnWO4@CNT nanocomposite shows 231 mAh g?1 and 257 mAh g?1 charge/discharge capacity which are higher than that of GeO2/ZnWO4 nanocomposite. The GeO2/ZnWO4@CNT nanocomposite delivers 75.8% capacity retention and 100% coulombic efficiency even after 400 cycles at 300 mAh g?1. These results direct that GeO2/ZnWO4@CNT nanocomposite is a good negative electrode for lithium-ion battery. [Figure not available: see fulltext.]. © 2020, Springer-Verlag GmbH Germany, part of Springer Nature.Item ZnWO4/SnO2 composite for supercapacitor applications(Elsevier B.V., 2020) Vinayaraj, S.; Brijesh, K.; Dhanush, P.C.; Nagaraja, H.S.The pristine ZnWO4 and ZnWO4/SnO2 composite was synthesized by solvothermal method. The crystal structure of the ZnWO4 and ZnWO4/SnO2 composite is determined by powder X-ray diffraction (XRD) pattern. The morphology of the samples investigated using SEM and found to be agglomerated structure. The samples are tested as an electrode material for supercapacitor using electrochemical techniques like cyclic Voltammetry (CV), Galvanostatic Charge-Discharge (GCD) and Electrochemical Impedance Spectroscopy (EIS). The ZnWO4/SnO2 composite reveals 56.7 F/g specific capacitance at 1 mV/s scan rate which is higher than that of pristine material and also ZnWO4/SnO2 composite exhibits good cyclic stability than pure ZnWO4. © 2020 Elsevier B.V.