Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Surface design of Mg-Zn alloy temporary orthopaedic implants: Tailoring wettability and biodegradability using laser surface melting(Elsevier B.V., 2018) Manne, B.; Thiruvayapati, H.; Bontha, S.; Motagondanahalli Rangarasaiah, R.; Das, M.; Balla, V.K.Magnesium-based alloys have attracted significant attention for biomedical applications due to its biodegradability as well as density and elastic modulus which are close to those of human bone. However, the uncontrolled biodegradation and hydrogen evolution are of major concern. In this work, laser surface melting (LSM) has been carried out to tailor initial corrosion rates of Mg-2.2Zn alloy implants. Melt pool dimensions, microstructure and surface topography of the LSM samples were analysed. The wettability and in vitro degradation characteristics of untreated and treated alloy were compared. LSM resulted in much finer cellular microstructural features than as-cast alloy and the melted region depths between 65 and 115 ?m. Higher treatment depths helped to extend the corrosion protection time by suppressing the corrosion front movement. Polished LSM samples resulted in overall corrosion rates of 0.5–0.62 mm/year which was about 40%–50% reduction compared to the as-cast alloy. Accelerated biomineralisation of the surface via enhancements in the surface energy due to microstructural refinement as well as microstructural homogeneity and Zn enrichment in ?-Mg, favoured improvement of the overall corrosion performance of LSM-treated alloy. © 2018 Elsevier B.V.Item Effect of age hardening precipitates on the corrosion performance of laser Powder-Directed energy deposited CuNi2SiCr(Elsevier B.V., 2024) Urs, S.S.; Thanumoorthy, R.S.; Aswith Babu, I.; Doddamani, M.; Bontha, S.; Balan, A.S.S.This study explores Laser Powder ? Direct Energy Deposition (LP-DED) processing of CuNi2SiCr and the effect of heat treatment on corrosion behavior. The findings pave the way to increasing the life of the components and the possibility of refabrication upon failure. LP-DED manufactured CuNi2SiCr was subjected to solution treatment followed by age-hardening at 500? for 1,3,5 and 7 h. The microstructure analysis showed the formation of Cr3Ni precipitates due to a higher cooling rate in the LP-DED process. Upon aging, Ni3Si, Ni2Si, and CrSi2 precipitates evolved. Due to the Orowan phenomenon, microhardness increases with the aging time as the number of precipitates along the grain boundary increases with the aging time. The 5-hour aged sample exhibited the best corrosion resistance due to precipitation coherency in the matrix and the medium-sized precipitates with uniform precipitation-free zones (PFZ) in the grain boundary. © 2024 Elsevier B.V.Item Microstructure - corrosion performance correlation of laser directed energy deposited Inconel 625(Elsevier Ltd, 2025) Praharaj, A.K.; Bontha, S.; Balla, V.K.; Chakrapani, S.K.; Suvin, P.S.The primary objective of the current work is to understand the influence of process parameters on the corrosion performance of laser directed energy deposited Inconel 625 (IN625). In this regard, IN625 bulk samples were deposited using optimized laser power and three different scanning speeds. The as-deposited (AD) samples are named as AD-L, AD-M, and AD-H corresponding to low, medium, and high scanning speeds, respectively. Comprehensive microstructural characterization, microhardness evaluation, and electrochemical corrosion testing (medium: 3.5 wt% NaCl solution) were performed to correlate the process parameters with the microstructural features and corrosion performance. The results revealed that average grain size of the AD-H sample was lowered by 22.8 % and 19 %, respectively than the AD-L and AD-M samples, resulting in an enhancement of 8.4 % and 3.3 % in microhardness. Electrochemical corrosion tests indicated that AD-H sample possessed a higher corrosion potential (Ecorr) and a lower corrosion current density (Icorr) when compared to other samples, confirming the corrosion resistance of the samples in the order of AD-H > AD-M > AD-L. The higher scanning speed resulted in finer grains, high dislocation density, and lowered volume fraction of secondary phases, which are attributed to superior corrosion resistance of the AD-H sample. Surface analysis of the corroded samples suggested a greater susceptibility to localized corrosion over pitting corrosion. The current work provides valuable insights to the correlation between process parameters, microstructure, and corrosion performance of LDED fabricated IN625, confirming notable influence of scanning speed on the corrosion behavior. © 2025 Elsevier B.V.Item Unveiling the role of heat treatment approaches in tailoring corrosion performance of laser powder-directed energy deposited SS304(Elsevier B.V., 2025) Sasindran, J.; Narayanan, J.A.; Babu, I.A.; Balan, A.S.S.; Hebbar, H.S.; Bontha, S.This study investigates the effect of different post-processing heat treatment approaches on the corrosion behavior of Laser Powder-Directed Energy Deposited (LP-DED) SS304. Samples were fabricated using optimized LP-DED parameters: laser power of 400 W, scan speed of 800 mm/min, feed rate of 4 g/min, 0.6 mm beam diameter, and 33 % track overlap.Electrochemical analysis revealed significant differences in corrosion performance depending on the applied heat treatment approach. This treatment resulted in changes to residual stress, microstructure, and oxide layer characteristics which together influence the corrosion rate (CR). The stress-relief annealed (SRA) samples significantly improved corrosion resistance by up to 90 % compared to the as-built condition, while preserving the fine microstructure formed during the LP-DED process and maintaining a stable protective oxide layer. Solution treated and different quenched samples exhibited varying CR depending on the cooling rate and resulting coarse grain structure. These findings highlight the significant influence of post-processing heat treatments on corrosion behavior and microstructural characteristics. © 2025 Elsevier B.V.