Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Effect of equiaxed grains and secondary phase particles on mechanical properties and corrosion behaviour of CMT- based wire arc additive manufactured AZ31 Mg alloy(Elsevier Ltd, 2023) Manjhi, S.K.; Sekar, P.; Bontha, S.; Balan, A.S.S.Wire arc additive manufacturing (WAAM) has drawn tremendous attention for manufacturing large and complex components of lightweight material at a moderate cost due to its high deposition rate and energy efficiency. Generally, WAAM-Mg alloy comprises columnar and columnar dendrite grains due to high cooling rates and thermal gradients responsible for anisotropic mechanical properties. To overcome this challenge, in this work, CMT-WAAM, which generally uses comparatively low heat input (33% lower than conventional WAAM), was used to deposit AZ31 Mg thin wall. The metallurgical characterization of the deposited thin wall of the top (T), middle (M) and bottom (B) sections reveals equiaxed grains of average sizes ∼ 58, ∼ 63 and ∼ 38 µm, respectively. In addition, TEM results exhibit the formation of secondary phase particles, i.e., β-Mg17Al12 and ɳ-Al8Mn5. Further, the ultimate tensile strength (UTS) and % elongation (% EL) in the travel direction (UTS = 224 MPa, % EL= 23.47%) are superior to that obtained in the build direction (UTS = 217 MPa, % EL = 20.82%). The corrosion resistance of WAAMed AZ31 Mg alloy is higher than wrought (cold rolled) AZ31 Mg alloy in Hank's balanced salt solution (HBSS). The results of this study reveal the potential of CMT-WAAM to deposit different grades of Mg with desired microstructure, mechanical properties and corrosion resistance. © 2023 CIRPItem Evaluation of functionally graded YSZ - IN625 clad without bond coat using laser directed energy deposition(Elsevier B.V., 2023) Likhwar, J.; Thanumoorthy, R.S.; Bontha, S.; Balan, A.S.S.M-CrAlY or M-Cr-based bond coats are used as a buffer layer to apply ceramic thermal barrier coatings (TBCs) to metal turbine blades. However, due to oxygen diffusion, thermally grown oxides grow over the bond coat material, leading to coating failure in the components. Therefore, this study attempts to fabricate a novel TBC-coated IN625 without bond coat material using a Functional grading approach. The findings from this study may pave the way for processing functionally graded ceramic materials using Laser Additive manufacturing techniques. This study also evaluates the performance of functional grading in joining dissimilar materials using small spot-size laser sources. In the present study, samples were fabricated for three sample conditions: S1: direct clad, S2: 25% linear grading, and S3: 50% linear grading. The interface between Yttria Stabilized Zirconia (YSZ) and IN625 for the S1 sample showed discontinuous and horizontal cracks along the interface due to steep variations in thermal properties. However, the interface of S2 and S3 samples showed good adhesion and a smooth transition in microstructure between IN625 and YSZ as a result of functional grading. SEM micrographs showed homogeneous YSZ distributions without segregation within the IN625 matrix. This was attributed to strong Marangoni flow as a result of the small spot-size laser beam used in this study. © 2023 Elsevier B.V.Item Hybrid additive manufacturing of ER70S6 steel and Inconel 625: A study on microstructure and mechanical properties(Elsevier Ltd, 2023) Rodrigues, J.P.; Thanumoorthy, R.S.; Manjhi, S.K.; Sekar, P.; Arumuga Perumal, D.A.; Bontha, S.; Balan, A.S.S.Hybrid Additive Manufacturing (HAM) is currently being explored because of its potential to achieve trade-off between build capacity and feature resolution. The present study aims at fabricating ER70S6-Inconel 625 (IN625) bimetallic clad using hybrid Wire Arc Additive Manufacturing (WAAM) and Laser Directed Energy Deposition (LDED) processes. Microstructure evaluation was performed at the cross section of bimetallic clad for distinct materials as well as the interface. WAAM built ER70S6 revealed equiaxed ferritic grains, whereas laser deposited IN625 region showed columnar dendrites with under developed secondary arms. However, the first layer of IN625 exhibited columnar dendrite with secondary arms due to the influence of diffused Fe from the base ER70S6 steel under the action of concentrated laser heat source, which was revealed by energy dispersive spectroscopy (EDS) maps. The measured microhardness across the cross section of the deposit showed values corresponding to inherent material system. The interface did not reveal presence of any intermetallic phases which was confirmed by hardness results and X-Ray diffraction. Shear test revealed superior bond strength between the two materials, maintaining average strength of 452 MPa. The fractography images exhibited fine dimples along with cleavages indicating mixed fracture characteristics. This additive manufacturing method explores a new dimension in multi-material fabrication which, when customized for different materials, serve critical areas in the aerospace and defence sector. © 2023 Elsevier LtdItem Laser directed energy deposited Ti-48Al-2Cr-2Nb alloy: An investigation of high temperature oxidation behavior(Elsevier B.V., 2024) Gurugubelli, R.C.; Balla, V.K.; Rajasekaran, B.; Krishna, P.; Bontha, S.This study investigates high-temperature oxidation behavior and kinetics of Laser Directed Energy Deposited (LDED) Ti-48Al-2Cr-2Nb (Ti-48-2-2) alloy at 750 °C, 850 °C, and 950 °C, for 30, 60 and 100 h. Results reveal that the oxide-scale consists of alternating bands of TiO2 and Al2O3 and its stability is strongly dependent on the oxidation temperature and duration. At 850 °C and 950 °C, the oxide-scale delaminated following 100-h exposure. LDED Ti-48-2-2 exhibited an oxidation rate constant of 0.984 mg2 cm−4 h−1 at 850 °C (100 h) and 2.09 mg2 cm−4 h−1 at 950 °C (100 h), and an activation energy of 83.7 kJ mol−1 (850°–950 °C). LDED Ti-48-2-2 exhibited poor oxidation resistance compared to conventionally processed Ƴ-TiAl alloys. This can be attributed to the absence of N-rich layer and the typical nano-scale α2/γ banded lamellar microstructure observed in other processing routes. Post-process heat treatments can be utilized to obtain the desired microstructural features. © 2024 Elsevier B.V.Item Sequential hybridisation of wire and powder-based additive manufacturing of Inconel 718: Mechanical and microstructural characterization(Elsevier Ltd, 2024) Mudakavi, D.; B Sreesha, R.; Thanumoorthy, R.S.; Anar, S.; Krishnan R, A.; Suryakumar, S.; Bontha, S.; M Adinarayanappa, S.The present study combines the Wire-based DED (W-DED) and Powder-based DED (P-DED) to achieve a high deposition rate and higher feature resolution, respectively, within the single component. The research puts forward a novel Wire-Power (WP) Hybrid DED process, which is realized by sequential deposition of feedstock in Wire and then in Powder form. Based on the deposition-extraction combination, three sample configurations, C1 (Y-X), C2 (X-X) and C3 (Y-Z), were fabricated and characterized for the mechanical properties and microstructural aspects. OM images revealed defect-free P-DED and W-DED interface, while the EBSD analysis showed grain size variations owing to differences in the cooling rates. The Ultimate Tensile Strength (UTS) values of C1 and C2 configurations are about 132.2 and 139.7 % higher in comparison to C3. Low cycle fatigue results showed that the C2 sustained a higher number of completely reversed cycles to failure in comparison to the other configurations. The impact energy absorbed by C3 is the highest, affirming the strong W–P interface. © 2024 Elsevier B.V.Item Effect of CMT-WAAM Process Parameters on Bead Geometry, Microstructure and Mechanical Properties of AZ31 Mg Alloy(Springer, 2024) Manjhi, S.K.; Sekar, P.; Bontha, S.; Balan, A.A.S.Fabrication of Mg alloys using the additive manufacturing process is quite challenging owing to high oxidation and volatile nature at high temperatures. The present study investigates the effect of wire feed speed (WFS) and travel speed (TS) on single tracks of AZ31 Mg alloy fabricated using the cold metal transfer wire arc additive Manufacturing (CMT-WAAM) process. The WFS and TS of CMT-WAAM are optimized to achieve better deposition quality. An increase in WFS increased the width, height, penetration depth, and heat-affected zone of single tracks. In addition, increasing TS decreased the deposited tracks' contact angle and height. The average grain size at the interface zone, center and top portion of single tracks are 35, 42, and 60 μm. The x-ray diffraction results show only the presence of primary phase α-Mg; interestingly, the β-Mg17Al12 and η-Al8Mn5 secondary phases are identified by SEM + EDS and TEM images. The microhardness increased from the substrate to the top section of single tracks due to the increased volume fraction of secondary-phase particles. Based on the best-chosen process parameters obtained from single-track deposition, a multilayer AZ31 Mg thin wall is deposited. The UTS, YS, and % EL of the deposited thin wall in travel direction (TD) are 222 MPa, 102 MPa, and 18%, while in build direction are 202 MPa, 110 MPa, and 14%, respectively. The tensile strength and elongation % of TD and BD samples exhibited comparable properties and were higher than cast AZ31 Mg alloy. © ASM International 2023.