Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Investigation of third-order nonlinear optical properties of nanostructured Ni-doped CdS thin films under continuous wave laser illumination(Springer, 2019) Bairy, R.; Arasalike, A.; Shivakumar, G.K.; Radhakrishnan, K.; Bhat K, U.K.We report the third-order nonlinear optical (NLO) properties and optical limiting (OL) thresholds of pure CdS and Ni-doped CdS thin films have been investigated with the Z-scan technique under continuous wave laser excitation. Nanocrystalline CdS thin films with various doping concentrations of Ni (0%, 1%, 3%, 5% and 10 at. %) are prepared by spray-pyrolysis technique. XRD patterns reveal that all the prepared films are polycrystalline and the incorporation of Ni does not lead to major changes in the crystalline phase of Cd1-xNixS thin films. The surface morphology of the prepared films is impacted by the Ni-doping and is indicated by Field Emission Scanning Electron Microscopy (FESEM) images. With an increase in Ni-doping concentration, the energy band-gap value decreased from 2.48 eV to 2.23 eV. From the Z-scan data, it is observed that the material show strong two-photon absorption (2PA) and with an increase in Ni-doping concentrations from 0 to 10 at. %, the nonlinear absorption coefficient (?) are enhanced from 0.92 x 10-5 to 4.46 x 10-5 (cm W-1), nonlinear refractive index (n2) from 0.2967 x 10-9 to 0.1297 x 10-8 (cm2 W-1) and thereby the third-order NLO susceptibility (?(3)) values also increased from 1.7075 x 10-6 to 7.4743 x 10-6 (esu). OL characteristics of the prepared films are studied at the experimental wavelength. The results propose that the Cd1-xNixS film is a capable material for nonlinear optical devices at 532 nm and optical power limiting applications. © Springer Science+Business Media, LLC, part of Springer Nature 2019.Item Enhancing the electrochemical performance of ZnO anode by novel additive of MoS2–SnO2 nanocomposite for the zinc alkaline battery application(Springer, 2022) Prabukumar, C.; Meti, S.; Bhat K, U.K.ZnO nanorods and ZnO microrods are synthesized as the anode material for the Zn alkaline battery application. The present work studies the electrochemical performance of ZnO with regard to its size, morphology and MoS2–SnO2 nanocomposite as its additive towards the alkaline battery application. The properties, such as oxidation–reduction reaction, anti-corrosion behaviour, charge-transfer resistance and suppression of hydrogen evolution reaction (HER), are studied in detail. The structural characterization of ZnO samples is performed by using X-ray diffractometry. The morphological analysis of ZnO and MoS2–SnO2 nanocomposite is performed by using field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM), respectively. The atomic absorption spectroscopy (AAS) is employed to determine the solubility of ZnO samples in KOH solution. The electrochemical properties of the bare ZnO and the ZnO with MoS2–SnO2 additive (MoS2–SnO2/ZnO) samples are characterized by using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), cathodic polarization and Tafel polarization techniques. The ZnO with nanorod morphology shows better electrochemical performance than ZnO microrods and ZnO nanoparticles with sphere-like or plate-like morphology. The addition of MoS2–SnO2 nanocomposite with the ZnO improved the electrochemical activity, suppressed the HER activity and improved the anti-corrosion behaviour of the ZnO samples. © 2021, The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature.Item High-speed face milling of AZ91 Mg alloy: Surface integrity investigations(KeAi Publishing Communications Ltd., 2022) Marakini, V.; Pai, S.P.; Bhat K, U.K.; Thakur, D.S.; Achar, B.P.Magnesium (Mg) alloys are popular in the aerospace and automotive sector owing to their light-weight aspects. Amongst various Mg alloys, AZ91 alloy behaviour under machining has been trending and needs to be completely explored. The selection of optimal machining parameters is an important decision making process to achieve highest quality along with reduced cost and time. In this regard, this article describes experimental investigations to evaluate the performance of face milling operations on the surface characteristics of AZ91 magnesium alloy. The experiments were carried out with uncoated and PVD (Physical Vapour Deposition) coated carbide inserts at three levels of cutting speed (500, 700 and 900 m/min), feed rate (0.1, 0.2 and 0.3 mm/teeth) and depth of cut (0.5, 1.0 and 1.5 mm) under dry machining conditions. Major surface integrity indicators, such as roughness, hardness, residual stresses and microstructure are analysed. Chip morphology is also analysed and the correlation between chips and machined surface roughness is established. Face milling operation significantly improved surface roughness and microhardness of this alloy. Roughness improvement up to 85% (0.067 μm) and hardness improvement up to 33% (91.8 HV) is observed from the use of uncoated carbide inserts. Whereas, from PVD coated inserts, roughness improvement up to 81% (0.083 μm) and hardness improvement up to 60% (111.2 HV) is achieved. A similarity in behaviour between the two types of insert conditions are observed with increase in roughness from feed increase and decrease in hardness from cutting speed increase. Microstructural analysis showed PVD coated insert conditions producing surface with no defects, when compared to the crack observed in the surface from the use of uncoated carbide inserts. Marginally higher compressive residual stresses are detected at the surfaces from use of the uncoated inserts. Overall, due to no surface defect and the significant improvement in hardness and roughness from the PVD coated inserts, they are recommended for use in face milling operation for the cutting conditions investigated in this study. © 2022 The AuthorsItem Improvement of third-order NLO properties of vacuum deposited Cd1-xPbxS nanostructured thin films for optoelectronic device applications(Elsevier Ltd, 2023) Bairy, R.; Vijeth, H.; Kulkarni, S.D.; Murari, M.S.; Bhat K, U.K.A polycrystalline nanostructured cadmium lead sulfide thin film was deposited using the thermal evaporation (PVD) technique (Cd1-xPbxS with x = 0.00, 0.01, 0.05 and 0.1 wt.% of Pb). Structural parameters of as-prepared Cd1-xPbxS thin films have been studied through X-ray diffraction. The optical investigation demonstrates that Cd1-xPbxS film's optical band gap (Eg) may be adjusted from the visible to the near-infrared region. (2.64 - 2.42 eV). The film is substantially more appropriate for absorbing layers in solar cells and optoelectronic applications due to the large decrease in ‘Eg.’ The enhanced Pb doping was found to have altered the surface morphology, verified by Field Emission Scanning Electron Microscopy (FESEM) images. The doped films also showed a significant red shift in the band edge and increased transmittance in the visible and NIR regions. The third-order nonlinear optical (TONLO) parameters of the samples were determined from the Q-switched Nd: YAG laser with 65-ps pulse duration at 1064 nm. The investigated TONLO components such as nonlinear absorption coefficient (β), nonlinear refractive index (n2) and the susceptibility χ(3)were found to be in the range from 1.16 × 10−3 to 4.12 × 10−3 (cmW−1), 1.06 × 10−8 to 3.32 × 10−8 (cm2 W−1) and 1.23 × 10−4 to 5.62 × 10−4 (esu) respectively. The results indicate that Pb-doping on CdS nanostructures on surface morphology can be used to modify NLO characteristics.Cd1-xPbxS thin film is a potential and able material for optoelectronic device applications, as seen by these encouraging NLO results. © 2023 Elsevier Ltd