Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Preparation and antifouling properties of PVDF ultrafiltration membranes with polyaniline (PANI) nanofibers and hydrolysed PSMA (H-PSMA) as additives(Elsevier, 2014) Pereira, V.R.; Isloor, A.M.; Bhat, K.U.; A.F., A.F.Polyaniline (PANI) nanofibers were used as hydrophilic additives to study their effect on the performance of polyvinylidene fluoride (PVDF) ultrafiltration (UF) membranes. PVDF UF membranes were prepared by the phase inversion method with hydrolyzed polystyrene-co-maleic anhydride (H-PSMA) and PANI nanofibers as additives. PANI nanofibers were synthesized by rapid mixing reaction and were used as a hydrophilic modifying agent with varying concentrations (0-1.5 wt.%) in the membranes. The synthesized PANI nanofibers were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis. Hydrolyzed PSMA was prepared by the hydrolysis of PSMA and was used as a novel pore forming additive. The addition of PANI nanofibers into the membranes increased the membrane hydrophilicity, porosity, water uptake and permeability. The membranes also showed good antifouling nature during BSA (bovine serum albumin) filtration when compared to the pristine membrane without PANI nanofibers. Membrane with 1.0 wt.% PANI content showed highest permeability among the synthesized membranes. The membrane having highest permeability was subjected to heavy metal ion rejection which showed high rejection of 98.52% and 97.38% for heavy metal ions Pb2+ and Cd2+ respectively. © 2014 Elsevier B.V.Item Optimised microwave-assisted biosynthesis of silver nanoparticles from Nothapodytes foetida leaf extracts and its anti-microbial activities(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2016) Roopesh, R.; Geedhika, G.; D'Souza, J.; Anandhan, S.; Bhat, K.U.; Jaya M, J.; Fathima B, S.; Mohan Balakrishnan, R.M.The present investigation reports the biogenesis of silver nanoparticles (Ag NPs) using extracts of a medicinal plant Nothapodytes foetida. Total phenolic content (TPC) and ferric reducing antioxidant power (FRAP) assay were carried out for the microwave-assisted extract (MAE) of N. foetida using methanol as solvent and the conditions for extraction were optimised by response surface methodology (RSM). The effects of operating variables such as extraction time, temperature and ratio of sample to solvent were studied using central composite design (CCD). A mathematical model with a high determination coefficient (R2) for TPC (0.991) and FRAP (0.995) was obtained. The optimal conditions of extraction for TPC were 48.6 ºC, 23.15 min and 2.04:30 (g/mL) and for FRAP 52.31ºC, 12.32 min and 1.67: 30 (g/mL). Under these conditions, the experimental yields of TPC and FRAP were 2.426 mg gallic acid equivalents (GAE)/g dry powder and 14.985mg of FeSO4·7H2O/g of dry powder, respectively. Ag NPs were characterised using UV–Vis spectroscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy. The synthesised Ag NPs have also shown potent activity against the human pathogenic Staphylococcus aureus. © 2016 Informa UK Limited, trading as Taylor & Francis Group.Item Biosynthesis of copper nanoparticles using copper-resistant Bacillus cereus, a soil isolate(Elsevier Ltd, 2016) Tiwari, M.; Jain, P.; Raghu Chandrashekar, R.; Narayanan, K.; Bhat, K.U.; Udupa, N.; Rao, J.V.Microorganisms are useful systems for the production of biocompatible metal nanoparticles. Copper, an essential element of life, has good therapeutic potential. However, copper lacks suitable form for effective in vivo delivery, which has diminished its applicability. In this study, we produced biosynthesized copper nanoparticles (BCuNps) using a copper-resistant bacterial isolate from copper mine. The organism was able to tolerate >10 mM of copper and when analysed by 16S rRNA technique, showed 100% similarity with Bacillus cereus. BCuNps, produced by this microorganism, in cell-free filtrate, were characterized for surface plasmon resonance (SPR), particle's characteristics, spectroscopic properties and morphology. SPR peaks for BCuNps were recorded between 570–620 and 350–370 nm. BCuNps characteristics, namely particle size distribution, polydispersity index and zeta potential were found to be 11–33 nm, 0.433 and (?) 19.6 mV, respectively. Scanning electron microscope (SEM), transmission electron microscope (TEM) and atomic force microscope (AFM) analyses confirmed the uniform morphology; X-ray diffraction (XRD) spectrum revealed the crystalline nature; and Fourier transform infrared (FTIR) spectrum disclosed the presence of protein with BCuNps. A comparative evaluation of BCuNps with copper sulphate to determine their antimicrobial and cell toxicity levels was undertaken. BCuNps showed better antimicrobial effect and found to be safer against normal cell lines, such as HaCat, Vero and hFOB, than the copper sulphate control. © 2016 Elsevier LtdItem Effect of current density during electrodeposition on microstructure and hardness of textured Cu coating in the application of antimicrobial Al touch surface(Elsevier Ltd, 2016) Augustin, A.; Huilgol, P.; Udupa, K.R.; Bhat, K.U.Copper is a well proven antimicrobial material which can be used in the form of a coating on the touch surfaces. Those coating can offer a good service as touch surface for very long time if only they possess good mechanical properties like scratch resistance and microhardness. In the present work the above mentioned mechanical properties were determined on the electrodeposited copper thin film; deposited on double zincated aluminium. During deposition, current density was varied from 2 A dm?2 to 10 A dm?2, to produce crystallite size in the range of 33.5 nm to 66 nm. The crystallite size was calculated from the X-ray peak broadening (Scherrer?s formula) which were later confirmed by TEM micrographs. The scratch hardness and microhardness of the coating were measured and correlated with the crystallite size in the copper coating. Both characteristic values were found to increase with the reduction in crystallite size. Reduced crystallite size (Hall–Petch effect) and preferred growth of copper films along (111) plane play a significant role on the increase in the hardness of the coating. Further, TEM analysis reveals the presence of nano-twins in the film deposited at higher current density, which contributed to a large extent to the sharp increase of coating hardness compared to the mechanism of Hall–Petch effect. The antimicrobial ability of the coated sample has been evaluated against Escherichia coli bacteria and which is compared with that of commercially available bulk copper using the colony count method. 94% of E. coli cells were died after six hours of exposure to the copper coated surface. The morphology of the copper treated cells was studied using SEM. © 2016 Elsevier LtdItem Microstructural characterization of low temperature plasma-nitrided 316L stainless steel surface with prior severe shot peening(Elsevier Ltd, 2016) Jayalakshmi, M.; Huilgol, P.; Badekai Ramachandra, B.R.; Bhat, K.U.Surface nanocrystallization by severe deformation has proven beneficial as pre-treatment to plasma nitriding. It aids in achieving thicker nitride layers at lower temperatures thus making the process more economical. In austenitic stainless steels, severe deformation leads to formation of strain induced martensite on the surface while plasma nitriding alone forms expanded austenite. However, structural characteristics of surface layer of pre-deformed steel after plasma nitriding is still a matter of debate. In present study, 316L stainless steel was subjected to severe shot peening: followed by plasma nitriding at 400 °C for 4 h. Characteristics of sample surface before and after treatment were analyzed by scanning electron microscopy, X-ray diffractometry and transmission electron microscopy techniques. Results showed that, this duplex treatment leads to formation of about 45 ?m thick nitride layer; without CrN precipitation. This is significantly high compared to reported data considering the temperature and duration of nitriding treatment employed. Selected area electron diffraction pattern from topmost surface confirmed the co-existence of austenite and martensite while subsurface layer was predominantly consisting of lath martensite. This indicates that major phase in the nitrided layer is martensitic in nature and nitrogen supersaturation leads to transformation of small fraction of martensite to expanded austenite. © 2016 Elsevier LtdItem Metastable microstructures at the interface between AISI 321 steel and molten aluminum during hot-dip aluminizing(Elsevier B.V., 2018) Huilgol, P.; Udupa, K.R.; Bhat, K.U.The microstructure at the interface between AISI 321 stainless steel and molten aluminum was investigated which occurs during the process of hot-dip aluminizing. Microstructural characterization was carried out by scanning electron microscopy, transmission electron microscopy and X-ray diffraction. The study revealed the formation of metastable FeAlm and multiple twinned Al13Fe4 phases at the interface between steel and aluminum. Multiple twinned Al13Fe4 phase exhibits pseudo tenfold electron diffraction pattern. Another metastable phase Al3(NiFe) with an orthorhombic structure was formed as one of the eutectic phase mixture in the solidified aluminum topcoat. The Al3(NiFe) phase in the eutectic shares crystallographic orientation relationship with the Al matrix. Metastable intermetallic phases are being reported for the first time during hot-dip aluminizing. © 2018 Elsevier B.V.Item Precipitate evolution during severe plastic deformation of cast Al-Zn-Mg alloys and their thermal stability(Institute of Physics Publishing helen.craven@iop.org, 2019) Manjunath, G.K.; Huilgol, P.; Preetham Kumar, G.V.P.; Bhat, K.U.In the current investigation, an effort was made to understand the precipitate evolution process during equal channel angular pressing (ECAP) of an alloy composed of only aluminium, zinc and magnesium. For this purpose, three different compositions of cast Al-Zn-Mg alloys were selected and ECAP processed in route BC upto four passes. Microstructural observations indicated that, ECAP processing leads to refined structure possessing high density dislocations and large amount of grains with high angle grain boundaries. The precipitate volume in the alloys increased with increase in the zinc quantity in the alloy. Microstructural characterization through transmission electron microscope (TEM) and differential scanning calorimeter (DSC) revealed that, processing by ECAP results in structure having stable ? phase precipitates without the presence of GP zones and intermediate ?? phase precipitates. Thereby demonstrates that, ECAP process accelerates the precipitation kinetics and also shifts the morphology of the precipitates. Higher mechanical properties were noticed in the alloy containing large quantity of MgZn2 precipitates. © 2018 IOP Publishing Ltd.Item Microstructural investigations on the hot-dip aluminized AISI 321 stainless steel after diffusion treatment(Elsevier B.V., 2019) Huilgol, P.; Udupa, K.R.; Bhat, K.U.The microstructure of the hot-dip aluminized AISI 321 stainless steel was studied after diffusion treatment at 900 °C for 3 h. The microstructural characterization was carried out by scanning electron microscopy, transmission electron microscopy, and X-ray diffractometry. The microstructure of the as aluminized steel consisted of two regions, viz.; aluminum topcoat and aluminide layer. During the diffusion treatment, the coating transformed into a layered structure consisting of four layers. The Fe2Al5 phase was formed in the outermost layer and the presence of Al13Fe4 quasicrystalline approximant phase was observed. The innermost layer adjacent to the base metal transformed to ferrite phase with NiAl precipitates. Next, to this layer, a disordered FeAl phase was observed. The lattice parameter of the disordered FeAl phase was found to be larger than that of the ordered B2 FeAl phase. The layer between outer Fe2Al5 phase and disordered FeAl phase consists of a mixture of three phases, namely Fe2Al5, disordered FeAl and a new phase with the simple cubic structure. The phase with simple cubic structure shares cube on cube crystallographic orientation relationship with the disordered FeAl phase. © 2019 Elsevier B.V.