Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
10 results
Search Results
Item Biodegradability of PMMA blends with some cellulose derivatives(2006) Bhat, D.K.; Muthu, M.S.High polymer blends of Polymethyl methacrylate (PMMA) with cellulose acetate (CA) and Cellulose acetate phthalate (CAP) of varying blend compositions have been prepared to study their biodegradation behavior and blend miscibility. Films of PMMA-CA, and PMMA-CAP blends have been prepared by solution casting using Acetone and Dimethyl formamide(DMF) as solvents respectively. Biodegradability of these blends has been studied by four different methods namely, soil burial test, enzymatic degradation, and degradation in phosphate buffer and activated sludge degradation followed by water absorption tests to support the degradation studies. Degradation analysis was done by weight loss method. The results of all the tests showed sufficient biodegradability of these blends. Degradability increased with the increase in CA and CAP content in the blend compositions. The miscibility of PMMA-CA and PMMA-CAP blends have been studied by solution viscometric and ultrasonic methods. The results obtained reveal that PMMA forms miscible blends with either CA or CAP in the entire composition range. Miscibility of the blends may be due to the formation of hydrogen bond between the carbonyl group of PMMA and the free hydroxyl group of CA and CAP. © Springer Science+Business Media, Inc. 2006.Item Miscibility of poly(methylmethacrelate) and cellulose acetate butyrate blends in dimethyl formamide(2008) Muthu, M.S.; Bhat, D.K.The miscibility of poly(methylmethacrelate) (PMMA) and cellulose acetate butyrate (CAB) blends in dimethyl formamide (DMF) have been investigated by viscosity, density, refractive index and ultrasonic velocity studies. The polymer-solvent and blend-solvent interaction parameters and heat of mixing have been calculated using the viscosity, density and ultrasonic velocity data. The results indicated the existence of positive interactions in the blend polymer solutions and that they are miscible in dimethyl formamide in the entire composition range between 303-323 K. The study also revealed that variation in the temperature does not affect the miscibility of PMMA and CAB blends in DMF significantly. The presence of hydrogen bonding in the blends in the solid state has also been indicated by FTIR studies. SEM images also supported the miscibility of blends.Item Miscibility of polymethylmethacrylate and polyethyleneglycol blends in tetrahydrofuran(2009) Muthu, M.S.; Bhat, D.K.; Renganathan, N.G.The miscibility of polymethylmethacrylate (PMMA) and polyethyleneglycol (PEG) blends in tetrahydrofuran. (THF) has been investigated by viscosity, density, refractive index, and ultrasonic velocity studies. Various interaction parameters such as polymer-solvent and blend-solvent interaction parameters and heat of mixing have been calculated using the viscosity, density, and ultrasonic velocity data. The results indicated the existence of positive interactions in the blend polymer solutions and that they are miscible in THF in the entire composition range. The study also revealed that variation in the temperature does not affect the miscibility of PMMA and PEG blends in THF significantly. The presence of hydrogen bonding in the blends in the solid state has also been indicated by FTIR studies. © 2008 Wiley Periodicals, Inc.Item Polyvinyl alcohol-polystyrene sulphonic acid blend electrolyte for supercapacitor application(2009) Muthu, M.S.; Bhat, D.K.A new polymer blend electrolyte based on poly vinyl alcohol and poly styrene sulphonic acid has been studied as an electrolyte for supercapcitors. A carbon-carbon supercapacitor has been fabricated using this electrolyte and its electrochemical characteristics and performance have been studied. The conductivity has been calculated using the bulk impedance obtained through impedance spectroscopy. The real and imaginary parts of the electrical modulus of samples show a long tail feature, which can be attributed to high capacitance of the material. The super capacitor showed a fairly good specific capacitance of 40 F g- 1 and a time constant of 5 s. © 2008 Elsevier B.V. All rights reserved.Item Miscibility of poly(vinylidene fluoride) and cellulose acetate blends in dimethyl formamide(Chemical Publishing Co., 2011) Muthu, M.S.; Bhat, D.K.The miscibility of poly(vinylidene fluoride) (PVDF) and cellulose acetate blends in dimethyl formamide has been investigated by viscosity, density, refractive index and ultrasonic velocity studies. The polymer-solvent and blend-solvent interaction parameters and heat of mixing have been calculated using the viscosity, density and ultrasonic velocity data. The results indicated the existence of positive interactions in the blend polymer solutions and that they are miscible in dimethyl formamide in the entire composition range between 303-323 K. The study also revealed that the variation in the temperature does not affect the miscibility of poly(vinylidene fluoride) and cellulose acetate blends in DMF significantly. The presence of hydrogen bonding in the blends in the solid state has also been indicated by FTIR studies. SEM images also supported the miscibility of blends.Item Electrochemical properties of chitosan-Co3O4 nanocomposite films(Elsevier B.V., 2011) Bhatt, A.S.; Bhat, D.K.; Santosh, M.S.Chitosan-Co3O4 composite films have been prepared by solution casting method. The obtained films have been characterised by XRD and FESEM. The electrical properties of the films are examined by impedance spectroscopy in the temperature range 303-343 K. The impedance plot of the films pronounces the role of temperature in charge-transfer resistance of the composite. Frequency as well as temperature dependencies of dielectric constant and dielectric loss exhibit the general trend followed by carrier dominated dielectrics. Electric modulus parameters give an insight on the ionic conductivity and relaxation phenomena of the composite films. The dielectric parameters along with modulus data have been exploited to discuss the conduction mechanism in the material. The minimum activation energy of 3.9 kJ mol -1 and maximum room temperature conductivity of 1.94 × 10 -2 S cm-1 were found for composite film with 8% Co 3O4 content. © 2011 Elsevier B.V. All rights reserved.Item Miscibility studies of chitosan and starch blends in buffer solution(2012) Sudhakar, Y.N.; Holla, S.R.; Muthu, M.; Bhat, D.K.The miscibility of chitosan (CS) and starch in buffer solution (CH 3COOH and CH 3COONa) has been investigated by viscosity, density and refractive index methods at 303K, 313K, and 323K. Various interaction parameters such as polymer-polymer and blend-solvent interaction parameters and heat of mixing have been calculated using viscosity and density data. The results indicated the existence of positive interactions in the blend polymer solutions and that they are miscible below 40% of starch compositions. The study also revealed that variation of temperature does have significant effect on the miscibility of chitosan and starch blends. © 2012 Copyright Taylor and Francis Group, LLC.Item LiClO4-doped plasticized chitosan and poly(ethylene glycol) blend as biodegradable polymer electrolyte for supercapacitors(Institute for Ionics, 2013) Sudhakar, Y.N.; Muthu, M.; Bhat, D.K.Biodegradable polymer electrolyte comprising the blend of chitosan (CS) and poly(ethylene glycol) (PEG) plasticized with ethylene carbonate and propylene carbonate, as host polymer, and lithium perchlorate (LiClO4), as a dopant, was prepared by solution casting technique. The ionic conductivity has been calculated using the bulk impedance obtained through impedance spectroscopy. The variation of conductivity and dielectric properties has been investigated as a function of polymer blend ratio, plasticizer content and LiClO4 concentration at temperature range of 298-343 K. The DSC thermograms show two broad peaks for CS/PEG blend and increased with increase in the LiClO4 content. The maximum conductivity has been found to be 1. 1 × 10-4 S cm-1 at room temperature for 70:30 (CS/PEG) concentration. The electric modulus of the electrolyte film exhibits a long tail feature indicative of good capacitance. The activation energy of all samples was calculated using the Arrhenius plot, and it has been found to be 0. 12 to 0. 38 eV. A carbon-carbon supercapacitor has been fabricated using this electrolyte, and its electrochemical characteristics and performance have been studied. The supercapacitor showed a fairly good specific capacitance of 47 F g-1. © 2012 Springer-Verlag.Item Miscibility, water uptake, ion exchange capacity, conductivity and dielectric studies of poly(methyl methacrylate) and cellulose acetate blends(2013) Jois, H.S.S.; Bhat, D.K.In the last few decades, polymer blends with good miscibility and conductivity have been the focus of study for material scientists. Here, polymer blends of Poly(methyl methacrylate) (PMMA) and Cellulose acetate (CA) of varying blend compositions have been prepared by solution casting method and their miscibility, water uptake, ion exchange capacity (IEC) proton conductivity, and dielectric properties have been studied. Dimethyl formamide (DMF) was used as solvent. Fourier transform infrared spectra (FTIR) and Differential scanning calorimetry (DSC) measurements have been used to analyze the miscibility of the blends. Up to 50/50 PMMA/CA, water uptake showed an increasing trend and for other compositions the value decreased. Ion exchange capacity and conductivity of the blends decreased with increase in PMMA content of the blends. The variations in the blend properties have been attributed to the presence of specific interactions and exchangeable groups in the blend system. The proton conductivity of the blends is in the order of 10-3 S cm-1. Impedance analysis of the blends indicated the absence of any relaxation phenomenon in the blend system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3074-3081, 2013 Copyright © 2013 Wiley Periodicals, Inc.Item Enhancement and investigation of biodegradability of poly (methyl methacrylate) and poly (vinyl chloride) by blending with biodegradable polymer(Springer Science and Business Media Deutschland GmbH, 2023) Sudhakar, Y.N.; Muthu, M.; Bhat, D.K.Presently, society needs an eco-friendlier alternative for non-biodegradable polymers, nonetheless, synthetic polymers have established the market because of cost and easy to manufacture. To address the challenge of reducing the lifetime of degradation of these polymers, the scope of blending natural biopolymers is effective. This paper focuses on confirming the effectiveness of biodegradation in the molecular level of polymer blends between synthetic polymers and biopolymers. The synthetic polymers such as poly (methyl methacrylate) (PMMA) and poly (vinyl chloride) (PVC) were blended with varying compositions of biodegradable cellulose acetate butyrate (CAB). Using dimethylformamide (DMF) the films of PMMA/CAB, PVC/CAB blends were prepared by the solution casting method. Four different methods for studying biodegradability of these blends, namely soil burial test, enzymatic degradation, activated sludge degradation followed by microbial degradation were performed. The confirmation of degradation was done by NMR, FTIR, and Gel Permeation Chromatography (GPC) studies. Moreover, degradation analyses were determined by the weight loss method. Sufficient biodegradability was shown with an increase in CAB content in the blend. This work provides an approach for bringing about the degradation of synthetic polymers without much compromise on their properties. Also, the type of microorganisms that effectively degrades these polymer bends can be known. © 2022, The Author(s).