Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Biodegradability of PMMA blends with some cellulose derivatives(2006) Bhat, D.K.; Muthu, M.S.High polymer blends of Polymethyl methacrylate (PMMA) with cellulose acetate (CA) and Cellulose acetate phthalate (CAP) of varying blend compositions have been prepared to study their biodegradation behavior and blend miscibility. Films of PMMA-CA, and PMMA-CAP blends have been prepared by solution casting using Acetone and Dimethyl formamide(DMF) as solvents respectively. Biodegradability of these blends has been studied by four different methods namely, soil burial test, enzymatic degradation, and degradation in phosphate buffer and activated sludge degradation followed by water absorption tests to support the degradation studies. Degradation analysis was done by weight loss method. The results of all the tests showed sufficient biodegradability of these blends. Degradability increased with the increase in CA and CAP content in the blend compositions. The miscibility of PMMA-CA and PMMA-CAP blends have been studied by solution viscometric and ultrasonic methods. The results obtained reveal that PMMA forms miscible blends with either CA or CAP in the entire composition range. Miscibility of the blends may be due to the formation of hydrogen bond between the carbonyl group of PMMA and the free hydroxyl group of CA and CAP. © Springer Science+Business Media, Inc. 2006.Item Miscibility, water uptake, ion exchange capacity, conductivity and dielectric studies of poly(methyl methacrylate) and cellulose acetate blends(2013) Jois, H.S.S.; Bhat, D.K.In the last few decades, polymer blends with good miscibility and conductivity have been the focus of study for material scientists. Here, polymer blends of Poly(methyl methacrylate) (PMMA) and Cellulose acetate (CA) of varying blend compositions have been prepared by solution casting method and their miscibility, water uptake, ion exchange capacity (IEC) proton conductivity, and dielectric properties have been studied. Dimethyl formamide (DMF) was used as solvent. Fourier transform infrared spectra (FTIR) and Differential scanning calorimetry (DSC) measurements have been used to analyze the miscibility of the blends. Up to 50/50 PMMA/CA, water uptake showed an increasing trend and for other compositions the value decreased. Ion exchange capacity and conductivity of the blends decreased with increase in PMMA content of the blends. The variations in the blend properties have been attributed to the presence of specific interactions and exchangeable groups in the blend system. The proton conductivity of the blends is in the order of 10-3 S cm-1. Impedance analysis of the blends indicated the absence of any relaxation phenomenon in the blend system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3074-3081, 2013 Copyright © 2013 Wiley Periodicals, Inc.Item Preparation and characterization of phosphoric acid-doped hydroxyethyl cellulose electrolyte for use in supercapacitor(SpringerOpen, 2015) Sudhakar, Y.N.; Muthu, M.; Bhat, D.K.A new borax cross-linked biodegradable solid polymer electrolyte based on hydroxyethyl cellulose and phosphoric acid (H3PO4) was prepared. Characterizations of doped and undoped SPE were done using Fourier transform infrared spectroscopic and electrochemical studies. The ionic conductivity of the films increased with increase in acid concentration and the ionic conductivity obtained at 303 K was 4.1 × 10-3 S cm-1. Furthermore, effects of acid concentration on ionic conductivity and activation energy were discussed. Dielectric studies showed long tail-like feature indicating capacitive nature. A supercapacitor was fabricated and its electrochemical characteristics were studied. The supercapacitor showed a fairly good specific capacitance of 83 F g-1 at 2 mV s-1 and galvanostatic charge-discharge studies showed the mirror-like pattern with 98 % columbic efficiency. Cyclic stability was measured up to 2000 cycles. © 2015 The Author(s).Item Enhancement and investigation of biodegradability of poly (methyl methacrylate) and poly (vinyl chloride) by blending with biodegradable polymer(Springer Science and Business Media Deutschland GmbH, 2023) Sudhakar, Y.N.; Muthu, M.; Bhat, D.K.Presently, society needs an eco-friendlier alternative for non-biodegradable polymers, nonetheless, synthetic polymers have established the market because of cost and easy to manufacture. To address the challenge of reducing the lifetime of degradation of these polymers, the scope of blending natural biopolymers is effective. This paper focuses on confirming the effectiveness of biodegradation in the molecular level of polymer blends between synthetic polymers and biopolymers. The synthetic polymers such as poly (methyl methacrylate) (PMMA) and poly (vinyl chloride) (PVC) were blended with varying compositions of biodegradable cellulose acetate butyrate (CAB). Using dimethylformamide (DMF) the films of PMMA/CAB, PVC/CAB blends were prepared by the solution casting method. Four different methods for studying biodegradability of these blends, namely soil burial test, enzymatic degradation, activated sludge degradation followed by microbial degradation were performed. The confirmation of degradation was done by NMR, FTIR, and Gel Permeation Chromatography (GPC) studies. Moreover, degradation analyses were determined by the weight loss method. Sufficient biodegradability was shown with an increase in CAB content in the blend. This work provides an approach for bringing about the degradation of synthetic polymers without much compromise on their properties. Also, the type of microorganisms that effectively degrades these polymer bends can be known. © 2022, The Author(s).