Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Filters

2021 - 20233

Settings

Author: search.filters.author.Bekinal, S.I.Subject: search.filters.subject.Damping

Search Results

Now showing 1 - 3 of 3
  • No Thumbnail Available
    Item
    A Review of Superconducting Magnetic Bearings and Their Application
    (Institute of Electrical and Electronics Engineers Inc., 2022) Supreeth, D.K.; Bekinal, S.I.; Shivamurthy, S.R.; Doddamani, M.
    Magnetic bearings are being researched for high-speed applications, such as flywheel energy storage devices, to eliminate friction losses. As per Earnshaw's theorem, stable levitation cannot be achieved for a static passive magnetic bearing system. Fully passive stable levitation can be achieved with the help of superconducting magnetic bearings (SMB). This article provides an in-depth review of the modeling, analysis, and development of SMB. The different SMB configurations are highlighted, together with essential methodologies for estimating and improving their performance. The advancements in mathematical models used and the optimization of bearing characteristics are thoroughly discussed. Further, key developments in the application of SMB in flywheel energy storage systems are also reviewed. © 2002-2011 IEEE.
  • No Thumbnail Available
    Item
    Analysis of novel eddy current damper for multi-ring permanent magnet thrust bearing
    (Electromagnetics Academy, 2021) Deshwal, D.; Bekinal, S.I.; Doddamani, M.
    —This paper deals with analyzing a novel eddy current damper for an axially magnetized multi-ring permanent magnet thrust bearing (MPMTB). Initially, the bearing is optimized for maximum axial force by selecting three general parameters (air gap, outer diameter of stator, and length) using a generalized optimization procedure. Then, the axial force of an optimized bearing is validated with the mathematical model results. Finally, the novel and conventional eddy current dampers (ECDs) for an optimized MPMTB are analyzed for damping forces and coefficients using three-dimensional (3D) finite element transient analysis in ANSYS. Based on the analysis results, the proposed novel structure could be selected to replace the conventional one for providing damping to MPMTB effectively without affecting the radial air gap between the rotor and stator rings. © 2021, Electromagnetics Academy. All rights reserved.
  • No Thumbnail Available
    Item
    Dynamic response of 3D printed functionally graded sandwich foams
    (Emerald Publishing, 2023) Bonthu, D.; Bharath, B.; Bekinal, S.I.; Jeyaraj, J.; Doddamani, M.
    Purpose: The purpose of this study was to introduce three-dimensional printing (3DP) of functionally graded sandwich foams (FGSFs). This work was continued by predicting the mechanical buckling and free vibration behavior of 3DP FGSFs using experimental and numerical analyses. Design/methodology/approach: Initially, hollow glass microballoon-reinforced high-density polyethylene-based polymer composite foams were developed, and these materials were extruded into their respective filaments. These filaments are used as feedstock materials in fused filament fabrication based 3DP for the development of FGSFs. Scanning electron microscopy analysis was performed on the freeze-dried samples to observe filler sustainability. Furthermore, the density, critical buckling load (Pcr), natural frequency (fn) and damping factor of FGSFs were evaluated. The critical buckling load (Pcr) of the FGSFs was estimated using the double-tangent method and modified Budiansky criteria. Findings: The density of FGSFs decreased with increasing filler percentage. The mechanical buckling load increased with the filler percentage. The natural frequency corresponding to the first mode of the FGSFs exhibited a decreasing trend with an increasing load in the pre-buckling regime and an increase in post-buckled zone, whereas the damping factor exhibited the opposite trend. Originality/value: The current research work is valuable for the area of 3D printing by developing the functionally graded foam based sandwich beams. Furthermore, it intended to present the buckling behavior of 3D printed FGSFs, variation of frequency and damping factor corresponding to first three modes with increase in load. © 2023, Emerald Publishing Limited.